Whelen 7141008 User Manual

CONNECTOR MS3102E10SL-3P
2.60
5.14
FRONT
Mounting Gasket
Ø2.60
5.43
®
ENGINEERING COMPANY INC.
MADE IN THE U.S.A.
51 Winthrop Road Chester, Connecticut 06412-0684 Phone: (860) 526-9504 Fax: (860) 526-2009 Internet: www.whelen.com Sales/Service e-mail: aviation@whelen.com
Installation Guide:
Model 71410( )-series
Model(s) 7141008, 7141018
P/N:01-0771410-08, 01-0771410-18
LED Flashing Anti-Collision
Light Assembly
TSO-C96a CLASS III APPROVED
OPERATING INSTRUCTIONS:
Operational Voltage: . . . . . . . . . . . 28 VDC nominal
Average Input Current:. . . . . . . . . 0.32 Amps
Pulse Input Current: . . . . . . . . . . . 1.4 Amps @ .3 Seconds
The Model 71410 series LED anti-collision light assembly meets the requirements of FAR 91.205(c)(3).
CONTINUED AIRWORTHINESS: The 71410 series LED anti-collision light assembly is designed with 8 vertical columns consisting of 3 white LEDs each. Should any one LED or any vertical column fail, the unit must be repaired or replaced. NOTE: To reduce eye strain, use an optical filter such as dark glasses or a blue covering dome during LED inspection. Inspect the lens and replace if there is excessive scratching, discoloration or cracking.
INSTALLATION PROCEDURES: The following information is to assist in the installation of a Whelen LED anti-collision light system.
1. The installation procedure described in the following text will be confined to a single light installation, but is identical for multiple light installations.
2. Using the “suggested mounting hole pattern” prepare the aircraft for means to secure the LED anti-collision light assembly. Remove any existing mounting adapters.
3. 28 VDC (+) and (-) ground leads equipped with an appropriate sized breaker to be supplied to the LED anti-collision light assembly system. Both leads must be connected by an approved FAA connection. Insure that the wire leads are clear of any obstructions and ty-wrap as required.
4. Install the light assembly by securing to the aircraft using
5. All inverted (bottom) mounted units shall require waterproofing of
6. Check all avionics systems for interference from this installation.
7. A flight check should be performed by a properly certified pilot.
8. Update aircraft records, complete Form 337 and obtain FAA field
appropriate approved hardware. Refer to page 2. CAUTION! Do not touch the LEDs with either fingers or sharp objects. This could soil and/or damage the LED and effect the optical performance of the LEDs.
the flasher base assembly to the aircraft.
approval for installation, as required.
The conditions and tests required for TSO approval of this article are minimum performance standards. It is the responsibility of those installing this article either on or within a specific type or class of aircraft to determine that the aircraft installation conditions are within the TSO standards. TSO articles must have separate approval for installation in aircraft. The article may be installed only if performed under 14 CFR part 43 or the applicable airworthiness requirements.
Aviation
©2009 Whelen Engineering Company Inc. Form No.14356A(052914)
Page 1
1
1
1
4
1
1
1
1
1
1
1
1
4
4
4
1
1
1
1
ITEM PART NUMBER DESCRIPTION
MODEL 7141008 (28V) UPPER
MODEL 7141018 (28V) LOWER
ASSY, 28V WHITE LED ANTI COLLISION LIGHT
GASKET, LENS
SEAL, HR LT SERIES
LENS, CLEAR LED ANTI-COLLISION HARDCOAT
LENS, CLEAR LED ANTI-COLLISION HARDCOAT W/DRAIN
ADAPTER, 5-HOLE LENS RETAINER
WASHER, #4 LOCK-SPRING MS35338-135
SCREW, 4-40 X 5/16" PPHMS MS51957-14
SCREW, 6-32 X 1 1/4" PPHMS MS51957-35
CONNECTOR, MS3102E10SL-3P
HOUSING, MACHINED
NUTPLATE
01-0771410-08
01-0771410-18
01-0271852-00
38-0250885-00
38-0250225-00
68-4971082A30
68-4971082A31
07-571304-100
16-0050506135
14-0050505-14
14-0050503-35
39-5903711-25
11-450845-300
07-750976-100
QTY QTY
4
4
2
3
4
5
6
7
8
9
10
11
12
1
1
3
2
1
7 8
LED
MODULE
A
WIRING DIAGRAM
CONNECTOR MS3102E10SL - 3P
BLACKWHITE
AC
B
MS CONNECTOR WIRING
(REAR VIEW)
+28VDC
B
N/C
C
GND
5 x .156 thru Countersink to .281x100° on a 4.656 bolt circle
Ø
Ø
SUGGESTED MOUNTING HOLE PATTERN
#6-32 Flat Head 100° Countersink (typ)
FRONT
2.70 Wire Passage Hole
75°
75°
75°
75°
60°
6
5
4
9
10
11
12
Page 2
Loading...