Whelen 7117203 User Manual

®
ENGINEERING COMPANY INC.
51 Winthrop Road Chester, Connecticut 06412-0684 Phone: (860) 526-9504 Fax: (860) 526-2009 Internet: www.whelen.com Sales/Service e-mail: aviation@whelen.com
Installation Guide: 71172( )-series
Models 7117203, 7117204
P/N: 01-0771172-03, -04
LED Forward Position Light/
Red Strobe Assembly
MADE IN THE U.S.A.
POSITION LIGHT:
Operational Voltage: . . . . . . . 28 VDC (nominal)
Input Current: . . . . . . . . . . . . . 0.25 Amps
EQUIPMENT LIMITATIONS: A lighting system
consists of two lights, one located on each wingtip. The baseplate must be mounted parallel to the vertical and horizontal centerlines of the aircraft to project the patterns properly. The strobe tube assembly must be connected to a strobe power supply, such as Whelen model 70888, 70879 or other approved models. CONTINUED AIRWORTHINESS: The 71172 series LED wingtip position light assembly is designed with 3 LED’s. If any one LED fails, the unit must be repaired or replaced. Inspect the lens. Replace if there is excessive scratching, discoloration or cracking. INSTALLATION PROCEDURES: The following information is to assist in the installation of a Whelen 71172 LED Forward Position Light/Strobe System.
1. Choose the appropriate 71172( ) series replacement light assembly.
2. The installation procedure described in the following text will be confined to a single light installation, but is identical for multiple light installations.
3. Remove the old light, locate and save the existing +VDC lead and (-) ground lead. Clean and prep ends as required.
3.88
7117203 7117204
1.78
7117203 7117204
2.35
1.08
1.15 MIN
Ø1.25
4. Make sure the existing system is equipped with an appropriate sized breaker. Connect the existing +28 VDC lead to the POSITIVE wire on the input cable assembly (supplied with the light assembly). Connect the existing ground lead to the GROUND wire on the input cable assembly or use the supplied connector as shown in the illustrations. Both leads must be connected by an approved FAA connection. Insure that the wire leads are clear of any obstructions and ty-wrap as required. Connect the strobe, J1, to the strobe power supply as shown in the figure.
5. Remove the shroud from the light assembly.
6. Position the base of the new light assembly onto the mounting surface. Insert three (3) #6-32 pan head screws into the mounting hole and tighten firmly.
7. Reinstall the lens so that the two notches are positioned under the shroud, with each notch equidistant to the centerline.
8. Check all avionics systems for interference from the installation.
9. A flight check should be performed by a properly certified pilot.
10. Update aircraft records, complete Form 337 and obtain FAA field approval for installation, as required.
WHITE (+28VDC) BLACK (-) GROUND Length - 6.00" ±1.00"
.17
POS 3 - WHITE (TRIGGER) POS 2 - BLACK (CATHODE) POS 1 - RED (ANODE) Length - 6.00" ±1.00"
Aviation
©2008 Whelen Engineering Company Inc. Form No.14203 (061808)
Page 1
9
8
MOUNTING DIMENSIONS
1.75
.56
1.31 DIA.
1.00
.36
.50
7
.820
.82
3 x 0.140 DIA MOUNTING HOLE FOR #6-32 SCREWS
6
4
5
3
12
QTY. QTY.
*
*
-
1
-
1
11
11
11
11
11 111
1
ITEM
01-0771172-03
01-0771172-04
1
01-0271179-03
2
01-0271179-04
3
38-0230021-00
4
68-3950902A30
5
38-0130107-00
6
36-0050626-01
7
68-2290005-54
8
19-171122-100
14-0050508-27
9
PART NUMBER
7117203 POS/STROBE LIGHT, 28V (GRN)
DESCRIPTION
7117204 POS/STROBE LIGHT, 28V (RED)
71110 ASS'Y, POSITION/STROBE LIGHT 28V (GRN)
71110 ASS'Y, POSITION/STROBE LIGHT 28V (RED)
GASKET, W-1283/W-1285/A650
LENS, CLEAR FWD POSITION LIGHT HARDCOAT
GASKET, A427-4 1/4" THICK
ASS'Y, FLASHTUBE 6.00" LEADS W/GROMMET
LENS, RED/COATED A612 RC RETAINER, LENS MODEL 71110 IRIDITE/COMPLETE
SCREW, 6-32 5/16 PFHMS CSINK MS51959-27
Page 2
Loading...