ENGINEERING COMPANY INC.
2.60
3.64
MFG
LABEL
-00 (28VDC) Connector Wiring
-50 (14VDC) Connector Wiring
POS 1
POS 2
POS 1
POS 2
(+) 28VDC
(-) GROUND
(+) 14VDC
(-) GROUND
White
Black
Red
Black
(-) GROUND BLACK
20AWG(14VDC) ” ±1.0”
or
18
5.5
AWG(28VDC) 12” ±1.0”
(+) 14VDC RED
20
or
(+) 28VDC WHITE
18AWG 12” ±1.0”
AWG 5.5” ±1.0”
51 Winthrop Road
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-2009
Internet: www.whelen.com
Sales/Service e-mail: aviation@whelen.com
Installation Guide:
Model 71080( )-series
Model(s) 7108000, 7108050
P/N(s):01-0771080-00
01-0771080-50
LED Flashing Anti-Collision
Light Assembly
TSO-C96a
CLASS I, III;
APPROVED
OPERATING INSTRUCTIONS:
Operational Voltage: . . . . . . . . . 14 / 28 VDC nominal
Average Input Current: . . . . . . . 0.90 / 0.45 Amps
Peak Input Current: . . . . . . . . . . 4.0 / 2.0 Amps @ .3 Seconds
The Model 71080 series LED anti-collision light assembly meets the
requirements of FAR 91.205(c)(3).
EQUIPMENT LIMITATIONS: An approved anti-collision light assembly
should be located so that the light will not impair the crew’s vision or
detract from the conspicuity of the position lights. The baseplate must be
mounted parallel to the vertical and horizontal centerlines of the aircraft
to project the patterns properly.
Certain types of installations may require additional testing.
CONTINUED AIRWORTHINESS: The 71080 series LED anti-collision
light assembly is designed with 8 vertical columns consisting of 4 LEDs
each. Should any one LED or any vertical column fail, the unit must be
repaired or replaced. Inspect the lens and replace if there is excessive
scratching, discoloration or cracking. NOTE: To reduce eye strain, use
an optical filter such as dark glasses or a blue covering dome during
LED inspection.
INSTALLATION PROCEDURES: The following information is to assist
in the installation of a Whelen LED Anti-collision Light System.
1. Using the mounting detail information provided, prepare the aircraft
for means to secure the light assembly.
2. Carefully remove the #4 Phillips screw and lens retainer. Remove
the lens. CAUTION! Do not touch the LEDs with either fingers or
sharp objects. This could soil and/or damage the LED and effect
the optical performance of the LEDs.
3. Connect the light inputs according to the chart shown. Connect the
power lead to an appropriately sized breaker. Connections to be in
accordance with FAA approved methods.
4. Install the light assembly and insure that all leads are clear of any
obstructions and secured as required.
5. Install gasket, lens and lens retainer. Confirm proper gasket fit.
Reinsert screws and tighten firmly.
6. All inverted (bottom) mounted units shall require waterproofing of
the base assembly to the aircraft. NOTE: Drill a 1/8” hole in the
center of the lens for bottom mount units.
7. Check all avionics systems for interference from this installation.
8. A flight check should be performed by a properly certified pilot.
9. Update aircraft records, complete Form 337 and obtain FAA field
approval for installation as required.
Aviation
©2008 Whelen Engineering Company Inc.
Form No.14159B (060314)
The conditions and tests required for TSO approval of this article are minimum
performance standards. It is the responsibility of those installing this article either on
or within a specific type or class of aircraft to determine that the aircraft installation
conditions are within the TSO standards. TSO articles must have separate approval
for installation in aircraft. The article may be installed only if performed under 14 CFR
part 43 or the applicable airworthiness requirements.
Page 1
Suggested Mounting Hole Pattern
4 x #6-32 MTG holes
equally spaced on
a 2.170 bolt circle
#6-32 Pan Head
#6 Lock Spring
Washer
(typ)
1
1
4
1
ITEM
PART NUMBER DESCRIPTION
MODEL 7108000 (28V)
MODEL 7108050 (14V)
ASSY, 28V LED ANTI COLLISION LIGHT 71080
ASSY, 14V LED ANTI COLLISION LIGHT 71080
GASKET, LENS MODEL 71055 SERIES
LENS, CLEAR LED ANTI-COLLISION HARDCOAT
RETAINER, LENS IRIDITE COMPLETE
WASHER, #4 LOCK-SPRING MS35338-135
SCREW, 4-40 X 5/16 PPHMS MS51957-14
01-0771080-00
01-0771080-50
01-0271848-02
01-0271848-50
38-0250885-00
68-4971082A30
19-171047-100
16-0050506135
140050505-14
QTY QTY
1
1
4
4
1
4
2
3
4
5
6
7
11
12
3
4
5
6
7
Page 2