Whelen 7101501 User Manual
0.25
1.33
0.25
1.33
1.875
3 x 0.150 THRU
(countersink .281” dia. x 100°)
0.656
1.837 2.41
0.656
Model(s):
7101501 (Green)
7101502 (Red)
7101507 (Green
7101508 (Red)
Pin 1 - White (+) 28VDC
Pin 2 - Black (-) Ground
Pos. A - White/Blue (+) 28 VDC
Pos. B - White (-) Ground
(Shroud)
Model(s):
7101503 (Green)
7101504 (Red)
7101505 (Green)
7101506 (Red)
Model(s):
All
MADE IN THE U.S.A.
®
ENGINEERING COMPANY INC.
51 Winthrop Road
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-2009
Internet: www.whelen.com
Sales/Service e-mail: aviation@whelen.com
Installation Guide: 71015( )-series
Models 7101501, 02, 03, 04, 05, 06, 07, 08
P/N: 01-0771015-01, -02, -03, -04,
-05, -06, -07, -08
LED Forward Position
Light Assembly
OPERATING INSTRUCTIONS:
Operational Voltage:
(Operational from 22VDC - 32VDC)
. . . . . . . . . . 28 VDC nominal
Input Current:. . . . . . . . . . . . . . .0.3 Amps
EQUIPMENT LIMITATIONS: An approved forward position
lighting system consists of two lights, one located on each
wingtip, mounted behind a clear lens. The base plate must be
mounted parallel to the vertical and horizontal centerlines of
the aircraft to project the patterns properly.
Certain types of installations may require additional testing.
CONTINUED AIRWORTHINESS: The 71015 series LED
wingtip position light assembly is designed with 6 Green or 7
Red LED’s. If any one LED fails, the unit must be repaired or
replaced. Note: To reduce eye strain, use an optical filter such
as dark glasses or a blue covering dome during LED
inspection.
INSTALLATION PROCEDURES: The following information is
to assist in the installation of a Whelen LED Forward Position
Light System.
1. Choose the appropriate light assembly.
2. Using the mounting detail information provided, prepare
3. Connect the light inputs according to the chart shown.
4. Carefully remove the #4 Phillips screw (qty. 2) and
5. Using the appropriate hardware, install the unit to the
6. Reinstall the shroud.
7. Check all avionics systems for interference from the
the aircraft for means to secure the light assembly.
Connect the power lead to an appropriately sized
breaker. Connections to be in accordance with FAA
approved methods.
remove the shroud. CAUTION: Do not touch the LED
with either fingers or sharp objects. This could soil and/or
damage the lens and affect the optical performance of
the LEDs.
aircraft. Insure that all leads are clear of any obstructions
and secured as required.
installation.
Aviation
©2005 Whelen Engineering Company Inc.
Form No.14001B (010714)
TSO-C30c
TYPES I & II
APPROVED
Page 1
The conditions and tests required for TSO approval of this
article are minimum performance standards. It is the
responsibility of those installing this article either on or
within a specific type or class of aircraft to determine that
the aircraft installation conditions are within the TSO
standards. TSO articles must have separate approval for
installation in aircraft. The article may be installed only if
performed under 14 CFR part 43 or the applicable
airworthiness requirements.
8. A flight check should be performed by a properly certified pilot.
9. Update aircraft records, complete Form 337 and obtain FAA field
approval for installation, as necessary.
ITEM PART NUMBER DESCRIPTION
7101501 LED FORWARD POS. LIGHT (GRN)
7101507 LED FORWARD POS. LIGHT w/WHITE HOUSING (GRN)
7101502 LED FORWARD POS. LIGHT (RED)
7101508 LED FORWARD POS. LIGHT w/WHITE HOUSING (RED)
7101503 LED FORWARD POS. LIGHT (GRN) w/SHIELD CABLE
7101505 LED FORWARD POS. LIGHT (GRN) w/SHIELD CABLE
7101504 LED FORWARD POS. LIGHT (RED) w/SHIELD CABLE
7101506 LED FORWARD POS. LIGHT (RED) w/SHIELD CABLE
01-0771015-01
01-0771015-07
01-0771015-02
01-0771015-08
01-0771015-03
01-0771015-05
01-0771015-04
01-0771015-06
QTYQTYQTYQTYQTY QTY QTY QTY
FINAL ASSEMBLY, LED POS. LIGHT (RED) w/SHIELD CABLE
FINAL ASSEMBLY, LED POS. LIGHT (RED) w/SHIELD CABLE
FINAL ASSEMBLY, LED POS. LIGHT (RED) w/WHITE HOUSING
01-0271718-04
01-0271718-06
01-0271718-08
1
1
1
FINAL ASSEMBLY, LED POS. LIGHT (GREEN) w/SHIELD CABLE
FINAL ASSEMBLY, LED POS. LIGHT (GREEN) w/SHIELD CABLE
FINAL ASSEMBLY, LED POS. LIGHT (GREEN) w/WHITE HOUSING
01-0271718-03
01-0271718-05
01-0271718-07
1
1
1
FINAL ASSEMBLY, LED POS. LIGHT (RED)
01-0271718-02
1
FINAL ASSEMBLY, LED POS. LIGHT (GREEN)
01-0271718-01
1
1
SCREW, 4-40 x 3/16 (FLAT HEAD/CSNK MS24693-C1)
14-0050581-01
22222222
3
4
5
7
9
6
8
10
11
2
SHROUD (WHITE)
11-671024-200
11
SHROUD
11-671024-100
111111
Mounting Dimensions
Models: 7101501, 7101502
7101507, 7101508
11
23
5
1110
4
Models: 7101505, 7101506Models: 7101503, 7101504
1.177
1.837
.340
1.312
.656
1.00 MIN.
0.150 DIA.
(3 PLCS.)
Mounting hardware is not
included.
2
76
Mounting hardware is not
included.
1
2
98
Mounting hardware is not
included.
Page 2
Loading...