WH 2.1 SYSTEM
WH-C
WH-SR1
WH-SR2
USER INSTRUCTIONS: WH2.1 SYSTEM
Important Safety Caution
This symbol indicat es that there are important
operating and maintena nce instr uctions in the
literature accompanying this unit.
This symbol in di cates th at da ng erous vo ltage
constituting a risk of electric shock is present within
this unit.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including ampliers) that
produce heat.
Do not defeat the safety purpose of the polarised or grounding
plug. A polarised plug has two blades with one wider than the
other. A grounding plug has two blades and a third grounding
prong. The wide blade or the third prong is provided for your
safety. If the provided plug does not t into you outlet, consult
an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched
particularly at the plugs, convenience receptacles, and at the
point where they exit from the apparatus.
On ly us e at ta chmen ts /acce ss or ies spe ci fi ed b y th e
manufacturer.
Use only with the cart, stand, tripod, bracket, or
table specied by the manufacturer - or sold with
the apparatus. When a cart or rack i s used, use
caution when moving the cat/apparatus combination to avoid
injury from tip-over.
Unp lug this ap parat us durin g l ightn ing stor ms or whe n
unused for long periods of time.
Refer all serving to qualied personnel. Servicing is required
when the appa ratus has been damaged in any way, such
as power supply cord or plug is damaged, liquid has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
CAUTION: These serving instructions are for use by qualied
service personnel only. To reduce the risk of electric shock,
do not perform any serving other than that contained in the
operating instructions unless you are qualied to do so.
WARNING: To reduce the risk of re or electric shock, do not
expose this apparatus to rain or moisture. The apparatus shall
not be exposed to dripping or splashing and that objects
filled with liquids, such as vases, shall not be places on the
apparatus.
No naked flame sources, such as lighted candles, should be
placed on the apparatus.
CAUTION: Changes or modications not expressly approved
by the manufacturer could void the user’s authority to operate
this device.
WARNI NG: The mains power switch for thi s ap plianc e is
located on the rear panel. To permit free access to this switch,
the apparatus must be located in an open area without any
obstruction.
Correct disposal of this products. This marking
indicates th at this prod uct shoul d not be
di sp ose d wi th ot her hou se hol d wa stes
th rou gho ut the E U. To prev ent p oss ibl e
harm to the environment or h uma n health
from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse
of material resources. To return your used device, please use
the return and collection systems or contact the retailer where
the product was purchased. They can take this product for
environmental safe recycling.
USER INSTRUCTIONS: WH2.1 SYSTEM
CENTRE FRONTREAR
LEFTLEFT RIGHTRIGHT
Introduction
WH-C Centre Loudspeaker
The Wharfed ale WH-C centre speaker is a dedicated centre channel unit designe d for mounting
preferably above a TV screen (as show is position A) or below a TV screen (as show in postion B). If
the unit is mounted on top of the television, move it forward so that the front grilles are level with or
slightly in front of the screen. This will reduce reections from the screen and the top of the cabinet.
The loudspeaker should be located on a stable at surface to avoid any danger of movement when it is
vibrated by high sound levels.
The speaker is supplied with four self-adhesive feet. Apply one to each bottom corner of the unit before
mounting.
CONNECTION
You will need a single length of twin core cable. Connect the red (+) terminal of the centre unit to the
red (+) terminal of the ampliers centre channel output. Connect the black (-) terminal of the centre
unit to the corresponding black (-) terminal of the amplier. The connection panel uses screw terminals
- the drawing below illustrates the connection method.
Leaving a stub of 5mm protruding from the wall. Align the hole in the mounting bracket over the screw head and carefully lower
the unit onto the screw. The speaker should now be securely attached with the feet against the wall. Now connect the speakers to
the amplier.
Preparing Speaker Cables Connecting Speaker Cables
Centre Speaker
Positioning
Centre Channel Connections
USER INSTRUCTIONS: WH2.1 SYSTEM
CENTRE FRONTREAR
LEFTLEFT RIGHTRIGH T
REAR LEFT
REAR RIGHT
AV AMPLIFIER
WH-SR1 and WH-SR2 Loudspeakers
The Wharfedale WH-SR1 and WH-SR2 are bipolar units designed for wall mounting and intended for use solely as rear eects
speakers.
In a Home Theatre System, the directional cues come from the front and centre channels. The rear channels provide ambience
and rear perspective and for this purpose a bipolar design with its mix of direct and reected sounds ideal. To aid this eect we
recommend placing the WH-SR1 and WH-SR2 speakers in a high position behind the listener.
PREPARATION
Each speaker is supplied with four self-adhesive feet. Apply one to each rear corner before mounting.
CONNECTIONS
You will need one length of twin core cable per speaker. Connect the red (+) terminal of the Left rear unit to the red (+) terminal
of the ampliers Left rear channel output. Connect the black (-) terminal of this unit to the corresponding black (-) terminal of the
amplier. Repeat for the Right speaker. The connection panel uses screw terminals - the drawing above illustrates the connection.
MOUNTING
Connect the cable to the speaker. Site the speakers about 600 mm above the listening position and 2.5-3.5 metres apart, central
to the listener and behind the listening position. Ensure that the wall is sound and can support the product. Fix a suitable screw
rmly to the wall.
Preparing
Speaker
Cables
Wall- moun ting th e
WH-SR1 and WH-SR2
Loudspeakers
2
Connecting
Speaker
Cables
1
Rear Channel Connections
3
USER INSTRUCTIONS: WH2.1 SYSTEM
REAR
RIGHT
FRONT
LEFT
REAR
LEFT
CENTRE
FRONT
RIGHT
SUB
WOOFEER
REAR
RIGHT
FRONT
LEFT
REAR
LEFT
CENTRE
FRONT
RIGHT
SUB
WOOFEER
System Using WH-SR1 and WH-SR2
Surround Speakers
A Home Theatre System using WH surround speakers
System using conventional rear speakers
FRONT AND CENTRE CHANNELS
The front channel loudspeakers should be placed on either
side of the television screen, 2 to 3 metres apart, and rotated
slightly towards the listeners.
As the centre speaker carries the dialogue effects, it should
be placed central to the listening position and close the T V
screen.
Operating height is important. Ideally, the front and centre
channel speakers should be operated at the same height and
with the tweeters at ear level to a seated listener.
REAR CHANNELS
If the rear channels are WH-SR1 or SR2 surround units, mount
them as alr eady describ ed. We recom mend placing th e
speakers in a high position, angled towards the listener.
SUBWOOFER
As the ear is unab le to det ect the direction from whic h
deep bass originates, this allows freedom in positioning the
subwoofer. Varying the distance from the wall will alter the
amount of bass. Some prefer to place the subwoofer against a
corner of the room. This arrangement gives more bass at the
possible expense of clarity.
LOUDSPEAKER SIZES
Many digital AV processors require you to specify the size of
speakers in the various channels. These are usually 'Large' or
'Small'.
Unless your loudspeakers are large floor standing units, you
should choose 'Small' for the front channels, as the subwoofer
is going to be better at provid ing clean, deep, and louder
bass. Choose 'Small' for the surround channels and also for the
centre channel.
Set the subwoofer options on the processor to 'On' or 'Yes'.
This will route all the deep bass to the subwoofer.
SETTING LEVELS
Once the loudspeaker setting have been finalised, put the
AV amplifier in to its test mode (see instructions supplied
with your processor.). Adjust the levels until all channels are
reproduced at equal loudness.
NOTE: On some programme material the surround channel
may seem lower than the front. Do not readjust this level.
You may, however, need to adjust the subwoofer output level.
Avoid setting too high a level or you will swamp the sound
with bass which may be tiring to listen to and may limit the
subwoofer's ability to respond to large bass transients. Set a
sensible level going into the subwoofer from the AV processor.
The volume control on the subwoofer should be between 12
o'clock and 3 o'clock.
LFE
The Low Frequ ency Effec ts chann el was desi gned as an
additional bass channel with its own dedicated subwoofer. In
practice however, if all the speakers are set to 'Small', the LFE
channel will be combined with the bass from other channels
and all this feeds into the subwoofer. When you set the LFE
level from your AV processor, use care with this setting as the
LFE channel may contain powerful low frequencies which,
alt hough norm al in a cine ma, may overload a dom estic
subwoofer.
If, during a progr amme, you hear poppi ng or thu mping
noises coming from the subwoofer, immediately turn the AV
processor volume level down and then back o the LFE level.
USER INSTRUCTIONS: WH2.1 SYSTEM
Symptom
Possible Cause
System not switched on; Speaker cables shorting terminals out; Wrong source selected.
Front loudspeaker out of phase. Check all system connections and rectify. Subwoofer not
switched on; Subwoofer phase incorrect; Subwoofer crossover control too low.
No Sound
Sound lacks bass content
Bass reproduction indistinct
System level set too high; Bass control set too high; Speakers too close to room corners.
System level set too high; Objects on speakers/subwoofer; Objects too close to subwoofer.
System level set high; Subwoofer level set too high; LFE level see too high.
One or more loudspeakers is out of phase. Check all system connections and rectify.
(Read the manual for correct connection procedure.)
Subwoofer too close to TV. (Switch o system and TV. Move units away. Leave 15 mins.
Switch on.)
Subwoofer level set too high; LFE level set too high; Subwoofer incorrectly wired.
Excessive bass distortion at low
volumes
Excessive or distorted bass at
high levels
Distorted / rattling sound at
high levels
Popping or thumping from
the subwoofer
Indistinct sound;
Poor localisation of eects.
Poor localisation of dialogue
Television picture colour is
distorted
If this does cure the problem, back o the volume level at the
subwoofer.
Please read the relevant sections of your AV amplier manual
and fami liarise yourself with the various issues. If you are
unsure, consult your dealer for help.
CONNECTING WIRES
When wall mounting a loudspeaker the connec ting cables
may be unacceptably obvious.
It may be less obstrusive to route cables from the loudspeaker
to the ceiling and then within or immediately underneath the
ceiling or covering. The cable may then return to oor level at
a convenient room corner.
Service and Warranty
CARE & MAINTENANCE
If you play the speakers with the grilles o exercise great care.
NEVER touch the drive units which can easily be damaged.
The loudspeaker cabinets can be cleaned with a damp cloth
or with a spray furniture polish and a soft cloth. Apply the
spray sparingly to the cloth and then polish the cabinet. Never
apply spray directly to the cabinet.
GUARANTEE & SERVICE
In the unlikely event that your unit develops a fault you should
return it to your Wharfedale dealer using the original packing
to ensure safe shipping.
The terms of your guarantee may vary from country to country
but in all locations the guarantee excludes:
All da mage cause d t hroug h a ccident , m isuse, wear and
tear, neglect, incorrect installation, adjustment or repair by
unauthorised personnel.
Liability for damage or loss occurring in transit to or from the
purchaser.
Wharfedale will not be liable for any consequential damage,
lo ss or inju ry, ar ising from or in con junct io n wi th thi s
equipment.
Troubleshooting
If your system is not working properly please work through this checklist before returning a unit to your dealer.
Specications and Service
WH-SR1 WH-SR2 WH-C
USER INSTRUCTIONS: WH2.1 SYSTEM
Nominal Impedance
Power Handing
Sensitivity (1W@1m)
Frequency Response
Bass Unit
Treble Unit
Dimensions Overall
H×W×D (mm)
6 Ohms
80 W (programme)
85dB
140Hz – 20kHz
100mm
28mm Dome
235×221×80
AUTHORISED SERVICE CENTRE
UK:
IAG Service Centre,
Unit 4, St Margaret’s Way,
Stukeley Meadows Industrial Estate,
Huntingdon, Cambs,
PE29 6EB
England
Tel: +44 (0) 1480 45256
Fax: +44 (0) 480 413403
6 Ohms
120 W (programme)
88dB
80Hz – 20kHz
100mm x 2
28mm x 2 Dome
235×262×126
6 Ohms
120 W (programme)
89dB
80Hz – 20kHz
100mm x 2
28mm Dome
150×390×135
For information on the authorised se rvice cent res worldw ide conta ct Wharfed ale Intern ational in the UK. A worldwide
distributor list is available on the Wharfedale website: www.wharfedale.co.uk
Wharfedale has a policy of continuous product development and reserves the right to change specification without notice.
IAG Hous e, Sover eign Cou rt, Ermi ne Busin ess Park , Huntin gdon, Ca mbs, PE2 9 6XU, U K
Tel: +44(0 )1480 447700 F ax: +4 4(0)14 80 431 767 http ://www.w harfed ale.c o.uk
IAG reserves the right to alter the design and sepcications without noctice. All rights reserved IAG Group Ltd.
Wharfedale is a member of the International Audio Group. CODE: WH11-MNL0015
Loading...