Wharfedale Titan Sub A15 User Manual

PROFESSIONAL SOUND SYSTEMS

Series

OPERATING MANUAL AND USER GUIDE

Titan™ 8 Passive

Titan™ 12 Passive

Titan™ 15 Passive

Titan™ 8 Active

Titan™ 12 Active

Titan™ 15 Active

Titan™ Sub A12

Titan™ Sub A15

www.wharfedalepro.com

OPERATING MANUAL AND USER GUIDE

IMPORTANT WARNINGS & SAFETY INSTRUCTIONS - GENERAL

READ ALL INSTRUCTIONS

1.

products before operating them.

RETAIN THESE INSTRUCTIONS

2.

COMPLY WITH ALL WARNINGS

3.

USE WITH AMPLIFIERS

4.

establish and follow a routine for powering up and powering down a sound system. With all system

components connected, turn on source equipment (mixers, signal processors, record and playback

units, etc.) BEFORE powering up amplifiers. Transient voltages from powering up source equipment

can damage speakers if amplifiers are already turned on. Make sure that amplifier volumes are

set to their minimum settings and power up any system amplifiers LAST. It is recommended that

all system components be allowed to stabilize for several seconds before any source signals are

introduced or level setting adjustments are made. Similarly, when shutting systems down, turn all

amplifiers off first, before powering down any other system components. This also applies to active

or self-powered speakers, Switch them on LAST and off FIRST.

CABLES

5.

6.

7.

8.

– Do not use shielded or microphone cables for connection between amplifiers and

speakers. Use only approved speaker cables with proper connectors.

RIGGING – SUSPENDING – MOUNTING

systems can expose members of the public to serious health risks and even death.

CIRCUMSTANCES ATTEMPT TO RIG, SUSPEND OR OTHERWISE MOUNT THESE SPEAKERS UNLESS

YOU ARE FULLY QUALIFIED AND CERTIFIED TO DO SO BY RELEVANT LOCAL, STATE AND NATIONAL

AUTHORITIES. ALL RELEVANT SAFETY REGULATIONS MUST BE FOLLOWED. IF YOU ARE NOT PROPERLY

QUALIFIED OR DO NOT KNOW OF PERTINENT REGULATIONS, CONSULT QUALIFIED PERSONNEL FOR

ADVICE.

CAUTION

pressure levels. Use care with placement and operation to avoid exposure to excessive volume levels.

Permanent hearing damage can result when operated to extreme levels.

SERVICE

service this product. Warranty nullification could result if this is attempted.

– These professional loudspeaker systems are capable of generating very high sound

– There are no user serviceable parts inside this product. Users should not attempt to

carefully and become familiar with the features and functions of these

for future reference.

– All warnings and instructions for this product should be adhered to.

– In order to avoid damage to drivers and other equipment, it is advisable to

– Rigging, suspending and mounting of these speaker

UNDER NO

1

Wall Mounting Titan Speaker System

WPB-1 Wall Mounting Bracket (Titan™ 12 / 15)

WHARFEDALE PRO LIMITED WARRANTY

Wharfedale Pro Titan™ Series speakers are warranted of manufacturing or material defects for a
period of one year from the original date of purchase. In the event of malfunction, contact your
authorized Wharfedale Pro dealer or distributor for information.

*Be aware that warranty details may differ from country to country. Contact your dealers or
distributor for information. These terms do not infringe your statutory rights.

30

OPERATING MANUAL AND USER GUIDE

TABLE OF CONTENTS

1……………………………..Important Warnings & Safety Instructions

2……………………………..Important Safety Information Powered Products

4……………………………..What about the Titan™ Series?

5……………………….…….Introduction/Overview

6……………………….…….Features

7……………………………..Setting up/ Speaker Placement

7……………….…………….Connections/ Wiring - Passive

8……………….…………….Rear Panel Layout - Passive

8……………….…………….Connection Diagram Passive

12……………….…………….Rear Panel Layout - Active

15…………..……………..….Connection Diagram Active

16…………..……………..….Rear Panel Layout - Sub A12

17……………….…………….Connection Diagram Sub A12

19……………….…………….Rear Panel Layout - Sub A15

20……………….…………….Connection Diagram Sub A15

22……………………….…….Specifications - Titan™ Passive

23……………………….…….Specifications - Titan™ Active

25……………………….…….Specifications - Titan™ Subwoofers

26……………………………..Dimensional Drawings - Titan™ 8/ 12

27…………..…………………Dimensional Drawings - Titan™ 15/ 8A

28…………..…………………Dimensional Drawings - Titan™ 12A / 15A

29…………..…………………Dimensional Drawings - Titan™ Sub A12/A15

30…………………………..…Wall Mounting Titan Speaker System

30…………………………..…Warranty

3

DIMENSIONS

12.28"

312mm

21.88"

556mm

O

MIX

_

-­OPTIMIZER

BR

O

)

O

(BALANCED)

NCED)

(BALA

A

OUTPU

INPUT

T

A

15.11"

384mm

12.28"

312m

m

7.1"
m

180m

15.83”

402mm

27.87”

708mm

15.83”

402mm

18.81”

478mm

28

OPERATING MANUAL AND USER GUIDE

TITAN™ SERIES OVERVIEW

The Titan™ Series are powerful, accurate, high quality loudspeaker systems with low

distortion that were designed to deliver high quality sound for the best value. From the

Titan™ 8 (passive) to the Titan™ 15 Active models plus two powered subs, you have what it

takes to assemble the system that your music deserves.

An important factor in loudspeakers is the smoothness of the sound coverage. Many

speakers that may sound acceptable in the horizontal plane have problems in the vertical

plane. Due to an integral high frequency Elliptical Wave Guide (EWG), the Titan™ speakers

exhibit very smooth and well behaved sound dispersion characteristics in both the horizontal

and vertical planes making positioning and set-up less critical. Everyone in the room will

hear the same quality sound.

The Titan™ Active Series has many features to allow you greater flexibility in your sound:

“BRO™ ” Bass Response Optimizer circuit, when engaged, allows for enhanced low

frequency response at lower volume levels. This is very similar to a loudness switch on your

home stereo amplifier.

Starting with the Titan™ 12 Active speaker, two-band EQ (equalization) is added. These

tone controls provide +/-10dB in each frequency range.

Sometimes, in live performance, it is not easy to know if your speakers are working or not;

they may be ahead of you when performing or they are not so close to you. To remedy this

problem, there is a POWER ‘ON’ indicator LED on the back panel as well as in the throat of

the horn to give you a visual indication that there is power to the speaker. There is also a

LIMIT indicator LED on the back panel. The LIMIT LED illuminates when the signal limiter is

actively limiting the level of the signal to prevent distortion and overload.

The Titan™ Series rugged cabinet features moulded in handles, feet, cord wrap and cable

anchors moulded into the lightweight Polypropylene cabinet. It also accommodates a bottom

mounted OmniMount® 60.0 bracket for wall mounting.

To make installation easier and safe, mounting and hanging brackets are available. The

diagrams at the end of this manual have rigging / hanging suggestions to get the most out

of your system.

5

DIMENSIONS

8.7”

221mm

15.59"

396mm

2

10.47”

266mm

8.7”

221mm

12.28”

312mm

21.89”

556mm

2

15.11”

384mm

12.28”

312mm

26

OPERATING MANUAL AND USER GUIDE

SETTING UP/ SPEAKER PLACEMENT

The uniform dispersion of the Titan™ Series makes it easy to place the speakers where you

need them, rather than trying to rearrange the room to accommodate the sound system. For

the best coverage and highest quality sound, the speakers should be located above head

level. Mounting hardware (M6/M8) and an integral tripod stand socket make installation

easy and safe. The Titan™ Series accommodates a bottom mounted OmniMount® 60.0

(Titan™ 12, 15) and OmniMount® 30.0 (Titan™ 8) bracket and has optional rigging /

hanging brackets.

Before turning on the Titan™ Series, or any powered loudspeaker, be sure that the power

switch is in the off position, volume controls are all the way down (at 0 level) and all audio

connections are made.

After power-up, speak into your mic or start the CD or MP3 player or other line level device

and slowly increase the volume to the desired level. Always remember that a speaker will

do what you tell it to do (i.e. deliver sound to the audience), but if the audience is too large

and your system too small, you will not achieve the desired sound level without a lot of

distortion. Avoid distortion as it can damage your speakers in the long term. If you cannot

achieve the desired SPL, you must add more speakers or a subwoofer to the system.

CONNECTIONS/ WIRING

Titan™ 8 / Titan™ 12 / Titan™ 15 Passive

Connecting the Titan™ Series to your system is easy. The rear panels include NL4 and 1/4”

phone connectors in parallel. Run your speaker wires from your amplifier to the speaker.

You can use either input connector. Use the correct gauge of speaker cable according to

the power handling ability of your Titan™ Series cabinet. Use stranded insulated cable for

speaker runs. It is always advisable to use heavier gauge (lower number) cables on longer

runs. Be sure to connect your speakers in proper polarity (what many refer to erroneously,

as phase). This means that in normal operation; connect one end of the same wire to the

Red terminal on the amplifier and the other end to the + (tip) connector on the speaker.

Black is always the ground or common.

Although the location of the speakers is not often critical to your sound, there are some

guidelines to follow, especially with powered speakers, to make the sound the best it can

be.

• Try to plug the amplifiers (a/k/a powered speakers) into a circuit that does not have light

dimmers or refrigerators on it. When these devices are in the circuit , it is almost certain

you will get a 50Hz hum in your system that cannot be removed with a EQ.

• Make sure the speakers are above head level to make the projection of the sound as

good as it can be. Keep the speakers out of the corner of the room. Place them away from

boundaries and the microphones. Do not place them too far apart.

• When using the hanging bracket or another apparatus, use a cable safety line attached to

the speaker and a solid part of the wall - not the bracket. If the bracket fails, the speaker

will not fall down.

• If the speakers will be hanging above the audience, it often is a good idea to turn the

speakers upside down and aim the horn 2/3 of the way back in the room.This will provide

good coverage of the audience.

7

SPECIFICATIONS - Titan™ ACTIVE (Con't)

Inputs

Input A – type

Input Sensitivity

Maximum Input Level

Input Connector

Input Impedance

Maximum Input Level

Input B – type

Input Sensitivity

Maximum Input Level

Input Connectors

Line Output

Line Output Connector

Impedance:

Sensitivity

AC Power details

Power Supply

AC Power Options

Power On Indicator

Rigging / Bracket / Mounting

Options

Enclosure Material

Colours

Dimensions H x W x D (mm)

Dimensions H x W x D (in)

Net Weight (kg / lbs)

Gross Weight (kg / lbs)

Titan™ 8 ACTIVE

Switchable balanced mic or line

level input

Mic: -36dBu (-38.2dBv or

12.28mVrms)

Line: +4dBu (1.78dBv or 1.228Vrms)

+22dBu

XLR - 1/4” Combo jack

Balanced: 20k ohms

+22dBu

High Efficiency Switching Mode

Power Supply

AC100~120V / 220~240V, 50 /

60Hz

LED

8 M6 threaded inserts including 4

M6 threaded

inserts on bottom in OmniMount

30.0-type footprint

Pole-mount receptacle with lock

screw

1 carry handles ( on each side)

Optional wall-mount bracket

Injection Moulded Polypropylene

Grey or white or black

396 x 266 x 221

15.6 x 10.5 x 8.7

5.7kg / 12.54lbs

7.70kg /16.94lbs

Titan™ 12 ACTIVE

Switchable balanced mic or line

level input

Mic: -36dBu (-38.2dBv or

12.28mVrms)

Line: +4dBu (1.78dBv or

1.228Vrms)

+22dBu

XLR - 1/4” Combo jack

Balanced: 20k ohms Unbalanced:

10k ohms

+22dBu

Line level input

XLR - 1/4” Combo jack: 1.78dBv

or 1.228Vrms

RCA: 0dBu (-2.2dBv or

0.775Vrms)

+22dBu

Combo jack: 1/4" - XLR / Summed

dual RCA jacks

Switchable LOOP / MIX Balanced

Male XLR

Balanced: 1k ohm Unbalanced:

500 ohm

+4dBu (1.78dBv or 1.228Vrms)

High Efficiency Switching Mode

Power Supply

AC100~120V / 220~240V, 50 /

60Hz

LED

10 M8 threaded inserts including

4 M8 threaded

inserts on bottom in OmniMount

60.0-type footprint

Pole-mount receptacle with lock

screw

2 carry handles (one on each

side)

Optional wall-mount bracket

Injection Moulded Polypropylene

Grey or white or black

556 x 384 x 312

21.9 x 15.1 x 12.3

12.8kg / 28.16lbs

14.8kg / 32.56lbs

Titan™ 15 ACTIVE

Switchable balanced mic or line

level input

Mic: -36dBu (-38.2dBv or

12.28mVrms)

Line: +4dBu (1.78dBv or

1.228Vrms)

+22dBu

XLR - 1/4” Combo jack

Balanced: 20k ohms Unbalanced:

10k ohms

+22dBu

Line level input

XLR - 1/4” Combo jack: 1.78dBv

or 1.228Vrms

RCA: 0dBu (-2.2dBv or

0.775Vrms)

+22dBu

Combo jack: 1/4" - XLR /

Summed dual RCA jacks

Switchable LOOP / MIX Balanced

Male XLR

Balanced: 1k ohm Unbalanced:

500 ohm

+4dBu (1.78dBv or 1.228Vrms)

High Efficiency Switching Mode

Power Supply

AC100~120V / 220~240V, 50 /

60Hz

LED

10 M8 threaded inserts including

4 M8 threaded

inserts on bottom in OmniMount

60.0-type footprint

Pole-mount receptacle with lock

screw

2 carry handles (one on each

side)

Optional wall-mount bracket

Injection Moulded Polypropylene

Grey or white or black

708.3 x 477.8 x 401.8

27.9" x 18.8" x 15.8

23.94kg / 52.67lbs

26.94kg / 59.27lbs

24

OPERATING MANUAL AND USER GUIDE

4

CONNECTION DIAGRAM # 2

Titan™ 8/12/15 MONO SYSTEM
WITH TWO MONITORS

CONNECTING MULTIPLE
Titan™ 8/12/15 SPEAKERS TOGETHER
IN A MONO-MAIN AND STAGE
MONITOR CONFIGURATION USING A
SINGLE, DUAL CHANNEL AMPLIFIER

MAIN SPEAKERS

STAGE MONITORS

OHM

LOAD

Left

OUTPUT OF STEREO POWER

AMPLIFIER OR POWERED MIXER

NOTE7KLVFRQ¿JXUDWLRQUHSUHVHQWVDRKPORDGWRHDFKRXWSXWFKDQQHORIWKHDPSOL¿HU

9

4OHM

LOAD

Right

SPECIFICATIONS - Titan™ PASSIVE SERIES

Loudspeaker Type:

Frequency Response (+/–3dB):

Sensitivity (1W@1M):

Peak SPL:

HF Coverage (H x V):

System Impedance:

POWER (WATTS)

Continuous:

Music:

Peak:

LF DRIVER

Size:

Coil Size:

HF DRIVER/ HORN

Coil Size:

Exit Size:

Diaphragm Material:

HF Driver Protection:

Long-Throw EQ Compensation:

Horn Type:

Throat Size:

CROSSOVER

Type/Frequency/Filter:

ENCLOSURE

Shape/ Material:

Rigging:

Titan™ 8

8" 2-way

70 - 20kHz

96dB

124dB

Ý[Ý

8 ohm

150W

300W

600W

203mm/ 8"

38.86mm / 1.53"

Compression Driver

25mm/1"

30mm/1.2"

Cloth

Bulb

N/A

EWG™ - Elliptical Waveguide

25mm/1"

2-way 2.4KHz / Linkwitz-Riley

Trapezoidal/ Polypropylene

(8) M6 threaded rigging points

+ (4) M6 threaded rigging points

on bottom in Omnimount®

30.0-type footprint + Speaker pole-

mount receptacle with lock screw

+ 1 built-in carry handle + Optional

wall-mount bracket + Optional

dual-unit array speaker stand

hardware

Titan™ 12

12" 2-way

55 - 20kHz

98dB

128dB

Ý[Ý

8 ohm

250W

500

1000

305mm/ 12"

64.26mm / 2.5"

Compression Driver

44mm/1.75"

25mm/1"

Titanium

DTF™ Dynamic Thermal Filament

3dB boost (long-throw) / Flat

(near-field)

EWG™ - Elliptical Waveguide

25mm/1"

2-way 2.2KHz / Linkwitz-Riley

Trapezoidal/ Polypropylene

(10) M8 threaded rigging points

+ (4) M8 threaded rigging points

on bottom in Omnimount®

60.0-type footprint + Speaker

pole-mount receptacle with lock

screw + Optional wall-mount

bracket + Optional dual-unit

array speaker stand hardware

Titan™ 15

15" 2-way

50 - 20kHz

97dB

129dB

Ý[Ý

8 ohm

400W

800W

1600W

381mm/ 15"

75mm / 3.0"

Compression Driver

51mm/ 2.0"

25mm/1"

Titanium

DTF™ Dynamic Thermal Filament

N/A

25mm/1"

2-way 1.8KHz / Linkwitz-Riley

Trapezoidal/ Polypropylene

(10) M8 threaded rigging points

+ (4) M8 threaded rigging points

on bottom in Omnimount®

60.0-type footprint + Speaker

pole-mount receptacle with lock

screw + Optional wall-mount

bracket + Optional dual unit

array speaker stand hardware

COLOURS

OUTPUT CONNECTORS

DIMENSIONS/WEIGHTS

Weight:

Dimensions (H x W x D):

Grey or Black or White

2 x 1/4" jacks + 2 x NL4

5.5kg / 12.1lbs

396 x 266 x 221mm/

15.59" x 10.47" x 8.7"

Grey or Black or White

2 x 1/4" jacks + 2 x NL4

12kg / 26.4lbs

556 x 384 x 312mm/

21.88" x 15.1" x 12.3"

Grey or Black or White

2 x 1/4" jacks + 2 x NL4

22kg / 48.4lbs

708.3 x 477.8 x 401.77mm/

27.9" x 18.8" x 15.8

22

OPERATING MANUAL AND USER GUIDE

CONNECTION DIAGRAM # 4

USING THE Titan™ 8/12/15
WITH A PASSIVE SUBWOOFER

AMPLIFIER OUTPUTS

OUTPUTAOUTPUT

B

TITAN™ 8/12/15 INPUT

INPUT:

+1Positive

-1N egative

PARALLEL INPUTS

WWW.WHARFEDALEPRO.COM

CONNECTION DIAGRAM # 5

USING THE Titan™ 8/12/15 IN A
BI-AMP SYSTEM

PASSIVE S UBWOOFER INPU T

PARALLEL
INPUT S

HI-PASSOUTPUT

(TOMID /HI SP EAKE R)

Hi-Pass Output to

Titan™ 8/12/15

PASSIVE SUBWOOFER

HI-PASS OUTPUT

MIXE R OUTPUT

ELECTRONIC CROSSOVER

Low Frequ ency Crossover Output High Frequency Crossover Outp ut

Low Frequency Amplifier Input

OUTPUTAOUTPUT

B

Low F requency Amplifier Output

High Frequ ency Amplifier Inpu t

OUTPUTAOUTPUT

B

High Frequency Amplifier Ou tput

Subwoofer Titan™ 8/12/15

INPUT:

+1Positive

-1Negative

PARALLEL INPUTS

PARALLEL

INPUT S

HI-PASSOUTPUT

(TOMID /HI SPEAKE R)

WWW.WHARFEDALEPRO.COM

11

CONNECTION DIAGRAM # 1

TWO CHANNEL SYSTEM WITH
HIGHPASS OUTPUT

Left

Output

Right

Output

TO LEFT ACTIVE SPEAKER

OR AMPLIFIER INPUT

A

THRU /

HIGHPASS

switch in
“HIGHPASS”
(down) mode

B

(BALANCED)

(BALANCED) (BALANCED)

INPUT

SPEAKER
LEVELIN

THRU

(100Hz)
HIGHPASS

(BALANCED)

OUTPUT

OUTPUT

INPUT

I

_

I

I

I

I

8

VOLUME

PHASE

0

I

I

I

I

+6

I

0°

180°

AVIS: RISQUEDE CHOC ELECTRIQUE

LIMIT

ON

OFF

TO RIGHT ACTIVE SPEAKER

OR AMPLIFIER INPUT

WWW.WHARFEDALEPRO.COM

CAUTION

RISK O F ELEC TRIC SHO CK

DO NO T OPEN

WARNING: SHOCK HAZARD

POWER

DONOT OPEN

-NEPAS OUVRIR

N2082

AC2 20-240V~50Hz 400W

FUSET4AL250V

!

MIXER

SERIALNUMBER

POWER

6ZLWFKLQ³21´

XSPRGH

POWER

CORD

NOTE: This same connection configuration can be used with OUTPUT A and B used in a
full-range mode when the THRU/HIGHPASS switch is in the "THRU" (up) position.

20

OPERATING MANUAL AND USER GUIDE

Titan™ 12/15 ACTIVE REAR PANEL LAYOUT

HI / LOW EQ

2

(HTXDOizDWion

4

conWUoO A&B

RCA INPUT L & R

6

(LHIW DQG RiJhW

MIC / LINE swiWch

8

XLR / ¼" combo

10

jDcks IoU INPUT

conWUoOs

VOLUME

A&B

O O

MAX

HIGH

LOW

GAIN

(BALANCED)

INPUT

A

CD/TAPE

HHDW Sink

POWER ON

LED inGicDWoU

0

MAX

+10dB

-10dB

0

ON

OFF

-10dB +10dB

MIX

LOOP

(BALANCED)

OUTPUT

DQG LIMIT LED

POWER ON /

OFF swiWch

ciUcXiW swiWch

OUTPUT soXUFH

LOOP / MIX

POWER

connHcWoU

OUTPUT

connHcWoU

inGicDWoU

³BRO™”

swiWch

XLR

1

3

5

7

9

11

12

13

Titan™ Sub-A12 CONNECTION DIAGRAM # 2

USING TWO Titan™ Sub-A12 WITH
TWO POWER SPEAKERS

L

(BAL/UNB AL (BALANC ED 

R

INPUT

120Hz 150Hz

100Hz 180Hz

200Hz

80Hz

0

180

MAX

LOW

PASSFILTER

AC220

240V50Hz

250W

OUTPUT

FUSE

T3.15AL250V

120Hz 150Hz

100Hz 180Hz

200Hz

80Hz

0

PASSFILTER

180

LOW

MAX

L

(BAL/UNB AL (BALANC ED 

R

INPUT

AC220

240V50Hz

250W

OUTPUT

FUSE

T3.15AL250V

18

OPERATING MANUAL AND USER GUIDE

Titan™12A / 15A CONNECTION DIAGRAM # 1

Basic microphone / playback hookup

MP3 Player

Titan™12A / 15A CONNECTION DIAGRAM # 2

Connecting two Titan™ 12 ACTIVE speakers together

%HDZDUHRI0,&/,1(VZLWFKVHWWLQJ

,QSXWIURP DPLFURSKRQHRU

WKHRXWSXWRI DPL[HU

0

-

+6 +6



VOLUME

HIGH

LOW

GAIN

(BALANCED)

INPUT

INPUT

INPUT

A

Microphone

-



VOLUME

-

GAIN



VOLUME

L

R

CD/TAPE

0

HI

0

0

MAXMAX

-12dB +12dB

+10dB-10dB

LOW

0

INPUT

-12dB +12dB

+10dB-10dB

EQ

MIX

LOOP

LIMIT

OFF

POWER

BASSRESPONSE

OPTIMIZER

AC INPUT

ON

OFF

ON

Place switch

down in

“MIX”

position

AC Power Cord

AC220-240V~60Hz

AC220-240V~50Hz

400W

FUSET4AL 250V

(BALANCED)

OUTPUT

B

Connect to power outlet

HI

0

0

MAXMAX

-



VOLUME

L

HIGH

INPUT

LOW

R

CD/TAPE

-10dB

LOW

-12dB +12dB

-10dB

LOOP

+10dB

0

+10dB

EQ

MIX

LIMIT

OFF

POWER

BASSRESPONSE

OPTIMIZ ER

AC INPUT

ON

OFF

ON

Place switch

down in

“MIX”

position

AC220-240V~60Hz

AC220-240V~50Hz

400W

(BALANCED)

OUTPUT

0

-12dB +12dB

+10dB-10dB

0

-10dB

-12dB+12dB

+10dB

EQ

MIX

(BALANCED)

OUTPUT

FUSET4AL 250V

LIMIT

POWER

OFF

BASSRESPONSE

OPTIMIZER

AC INPUT

AC220-240V~60Hz

AC220-240V~50Hz

400W

FUSET4AL 250V

ON

OFF

ON

Place switch

down in

“MIX”

position

-



VOLUME

(BALANCED)

INPUT

INPUT

INPUT

INPUT

A

0

MAX

+6 +6

HIGH

LOW

(BALANCED)

INPUT

INPUT

OUTPUT

INPUT

A

-



L

R

VOLUME

INPUT

CD/TAPE

B

HI

0

MAX

LOW

LOOP

B

15

Titan™ Sub A12 Rear Panel Features

HEAT SINK -

1.

VOLUME CONTROL -

2.

INPUT L -

3.

INPUT R -

4.

OUTPUT R -

5.

OUTPUT L -

6.

POWER SOCKET -

7.

LIMIT LED -

8.

POWER LED -

POWER SWITCH -

9.

PHASE SWITCH -

10.

CROSSOVER

11.

FREQUENCY

CONTROL-

Cooling fins for amplifier. Do not obstruct.

Adjusts the volume.

Balanced line level input via a XLR/ ¼” combo connector.

Balanced line level input via a XLR/ ¼” combo connector.

Balanced male XLR connector provides output HIGHPASS signal.

Balanced male XLR connector provides output HIGHPASS signal.

This is the connection for the IEC AC power connector.

LED indicator illuminates when the signal limiting function is activated.

LED indicator illuminates when the unit is powered up

Turns the power on and off to the subwoofer amplifier module.

Selects the polarity of the signal being sent to the subwoofer.

0° selects the signal polarity as it appears at the input.

The 180° selection inverts the polarity of the signal.

Adjustable 80Hz/100Hz/120Hz/150Hz/180Hz/200Hz.

1

2

CONTROL

3

4

HHDW Sink

VOLUME

INPUT L

INPUT R

MAX

L

(BAL/UNBA L (BALANCE D

R

INPUT

120Hz 150Hz

100Hz 180Hz

80Hz

LOW

PASSFILTER

OUTPUT

CROSSOVER FREQUENCY

CONTROL

200Hz

0

180

AC220

240V50Hz

250W

FUSE

T3.15AL250V

PHASE SWITCH

POWER SWITCH

LIMIT LED AND

POWER LED

POWER SOCKET

OUTPUT L

OUTPUT R

11

10

9

8

7

6

5

16

OPERATING MANUAL AND USER GUIDE

Titan™ Sub-A12 CONNECTION DIAGRAM # 1

TWO CHANNEL SYSTEM WITH HIGHAPASS OUTPUT

/HIW

2XWSXW

5LJKW

2XWSXW

MAX

L

(BAL/UNBA L (BALANCE D

R

INPUT

120 H z 150 Hz

100 H z 180 Hz

80H z

LOW

PASSFILTER

OUTPUT

200 H z

0

180

AC220

240V50Hz

250W

FUSE

T3.15AL250V

17

Titan™ 8/12/15 ACTIVE Rear Panel Features

Heat Sink:

1.
via air cooling at the rear of the enclosure.

HI and LOW EQ (equalization) controls:

2.
the overall output signal providing +/- 10dB in each frequency range.

POWER ´ON´ indicator LED and LIMIT indicator LED:

3.
of the POWER switch illuminates when the power switch is in the´ON´ position.

The
the signal to prevent distortion and overload.

VOLUME controls for INPUT A and INPUT B:

4.

each input channel (Titan

POWER ON / OFF switch:

5.

RCA L / R (Left and Right) input jacks:

6.
signal (left and right). The signal is actively combined or “summed” providing a
mono signal to the amplifier.

“BRO™” Bass Response Optimizer circuit switch:

7.
engaged, allows for enhanced low frequency response at lower volume levels.

The heat sink allows for dissipation of heat built up from the amplifier

These knobs control the equalization of

LIMIT LED

illuminates when the signal limiter is actively limiting the level of

8 VOLUME controls is MAIN) .

™

This switch: tums the power on and off.

These jacks provide for the input of a stereo

The bracketed LED to the left

These knobs control the volume of

The BRO™ circuit, when

GAIN selection switch:

8.
a microphone is connected to
source is anything other than a microphone (playback device, keyboard or mixer
output, for instance) use the

Output source “LOOP / MIX” switch:

9.
signal of

volume control. When in the MIX mode, this switch routes the combined (or

“mixed”) signals of both

XLR / ¼” COMBO input jacks for INPUT A and INPUT B:

10.
provide for either XLR or ¼” balanced input connections to

(Titan™ 8 XLR ¼” COMBO

POWER cord jack:

11.
electrical connection cord. Be sure that you are plugging into the correct source
voltage that matches what is indicated just below the power cord jack.

XLR line level OUTPUT jack:

12.

INPUT A

for connection to additional Titan™ 12 / 15 ACTIVES, powered subwoofers or

amplifiers.

INPUT B

and

INPUT B

This switch selects the proper gain structure for

INPUT A

LOW

to the line level XLR

INPUT A

input jacks for

This is a jack for a standard IEC, three prong, grounded AC

This jack provides a balanced line level output of

signals (in

, use the

selection (down) .

In the “

OUTPUT

INPUT B

and

MIX

mode) or

HIGH

selection (up). If the signal

LOOP

” mode, this switch routes the

jack, bypassing the EQ section and

to the line level XLR

These convenient jacks

INPUT A

INPUT

).

INPUT B

signal only (in

INPUT A

OUTPUT

INPUT B

and

LOOP

jack.

mode)

. If

14

OPERATING MANUAL AND USER GUIDE

Titan™ Sub-A15 - REAR PANEL FEATURES

. INPUT A

1

OUTPUT A

2.
(depending on switch setting).

SPEAKER LEVEL INPUT

3.
use the Titan™ Sub-A15 as a passivesubwoofer.

NOTE:

INPUT B -

4.

OUTPUT B -

5.
nding on switch setting).

HEATSINK -

6.

VOLUME CONTROL -

7.

- Balanced line level input via a XLR / ¼” combo connection.

- Balanced male XLR connection provides output “THRU” or HIGHPASS signal

Disconnect the power cord when using the Titan™ Sub-A15 in this mode.

Balanced line level input via a XLR / ¼” combo connection.

Balanced male XLR connection provides output “THRU” or HIGHPASS signal

Cooling fins for amplifier. Do not obstruct.

- Allows for connection of the output of an external amplifier to

Adjusts volume level of the subwoofer.

THRU / HIGHPASS SWITCH -

8.

Selects the signal type that is routed to the OUTPUT jacks.

“THRU” sends the unprocessed signal to the outputs. “HIGHPASS” filters the signal and

only sends signals above 100Hz to the outputs.

PHASE SWITCH -

9.

Selects the polarity of the singal being sent to the subwoofer. 0° selects
the signal polarity as it appears at the input. The “180°” selection inverts the phase of
the signal.

LIMIT LED -

10.

POWER LED -

11.

POWER SOCKET -

12.

POWER SWITCH -

13.

INPUT A

1

OUTPUT A

2

SPEAKER

3

LEVEL INPUT

INPUT B

4

OUTPUT B

5

LED indicator illuminates when the singal limiting function is activated.

LED indicator illuminates when the unit is powered up.

This is the connection for the IEC AC power connector.

Turns the power on and off to the subwoofer amplifier module.

HEATSINK

INPUT

(BALANCED)

A

SPEAKER
LEVELIN

B

(BALANCED) (BALANCED)

INPUT

THRU

(100Hz)
HIGHPASS

OUTPUT

(BALANCED)

OUTPUT

I

_

I

I

I

8

VOLUME

PHASE

0

I

I

I

MAX

I

0°

180°

I

I

WARNING: SHOCK HAZARD

AVIS: RISQUEDE CHOCELECTRIQUE

LIMIT

ON

OFF

POWER

WWW.WHARFEDALEPRO.COM

CAUTION

RISK OF ELECTR IC SHO CK

DONOT OPEN

N2082

AC220-240V~50Hz400W

FUSET4AL250V

DONOT OPEN

!

-NEPASOUVRIR

VOLUME

CONTROL

THRU/HIGHPASS

SWITCH

PHASE SWITCH

LIMIT LED

POWER LED

POWER SOCKET

POWER SWITCH

6

7

8
9

10

11

12

13

SERIALNUMBER

19

Titan™ 8 / Titan™ 12 / Titan™ 15 ACTIVE

Connecting the Titan™ Active Series to your system is just as easy, with a couple more things to do. Plug
in the electrical cable and your audio cables and switch the unit on. Always be sure there is a good
electrical ground. The Titan™ Series rear panel has one combo XLR / TRS Jack input. Be sure to use high
quality shielded cable and high quality connectors. The volume control is conveniently located above
the input sensitivity switch (mic/line). Be sure you have that switch in the correct position.

The Loop / Mix Switch - Titan™ 12A / 15A ONLY

The LOOP/MIX switch allows you to control the signal content going to the XLR OUTPUT jack. In the
“LOOP” mode, this switch routes the signal of INPUT B to the line level XLR OUTPUT jack, bypassing the
EQ section and volume control. When in the MIX mode, this switch routes the combined (or “mixed”)
signals of both INPUT A and INPUT B to the line level XLR OUTPUT jack. This signal can then be sent to
additional powered speakers or powered subwoofers.

Titan™ 8 ACTIVE - REAR PANEL FEATURES

4

VOLUME conWUoOs

MIC/ LINE swiWch

8

XLR oU 1/4”

10

combo jDcksIoU
INPUT

HHDW Sink

POWER ON

LED iQGicDWoU

DQG LIMIT LED

iQGicDWoU

POWER ON/OFF

swiWch

POWER

cRQQHcWoU

1

3

5

11

12

OPERATING MANUAL AND USER GUIDE

CONNECTION DIAGRAM # 2

USING TWO Titan™ Sub-A15's
WITH TWO POWERED SPEAKERS

INPUT

FROM

MIXER

OUTPUT

LEFT

(BALANC ED)

A

SPEAKER
LEVELIN

B

(BALANCED) (BALANCED)

INPUT

THRU

(100Hz)
HIGHPASS

OUTPUT

(BALANCED)

OUTPUT

0

I

I

I

I

I

I

I

I

_

I

8

MAX

I

VOLUME

0°

180°

PHASE

TO INPUT OF 2

SUBWOOFER

WWW.WHARFEDALEPRO.COM

CAUTION

RISK OF ELECTRIC SHO CK

DONOT OPEN

WARNING: SHOCK HAZARD

AVIS: R ISQUE DE CHOCEL ECTRIQU E

nd

ON

OFF

AC220-240V~50Hz400W

POWER

DONOT OPEN

N2082

FUSET4AL250V

-NEPASOUVRIR

TO LEFT

MAIN

POWERED

SPEAKER

!

POWER

CORD

POWER

CORD

POWER

CORD

SERIALNUMBER

LEFT SIDE

SUBWOOFER

FROM
MIXER

OUTPUT

RIGHT

TO RIGHT

MAIN

POWERED

SPEAKER

INPUT

(BALANC ED)

A

SPEAKER
LEVELIN

B

(BALANCED) (BALANCED)

INPUT

SERIALNUMBER

THRU

(100Hz)
HIGHPASS

OUTPUT

(BALANCED)

OUTPUT

RIGHT SIDE

SUBWOOFER

0

I

I

I

I

I

I

I

I

_

I

8

MAX

I

VOLUME

0°

180°

PHASE

LIMIT

ON

OFF

WWW.WHARFEDALEPRO.COM

CAUTION

RISK OF ELECTRIC SHO CK

DONOT OPEN

WARNING: SHOCK HAZARD

POWER

DONOTOPEN

N2082

AC220-240V~50Hz400W

FUSET4AL250V

AVIS: RISQUEDE CHOCELECTRIQUE -NEPASOUVRIR

!

POWER

CORD

21

CONNECTION DIAGRAM # 3

Titan™ 8/12/15 MONO MAIN
SYSTEM WITH TWO MONITORS
(another view)

FROM MIXER

MAIN OUT

FROM MIXER

MONI TOR OUT

INPUT:

+1 Positive

-1 Negative

PARALLEL INPUTS

WWW.WHARFEDALE PRO.COM

PARALLEL

CONNECTION TO

SECOND MAIN

EAKER

SP

OR

(CHANNEL 1)

TWO CHANNEL

AMPLIFIER OUTPUTS

MODELS-SERIES

ProfessionalPowerAmplifier

WWW.WHARFEDALEPRO.COM

MAIN SPEAKER #2MAIN SPEAKER #1

AMPLIFIER INPUTS

(CHANNEL 2)

MONITOR SPEAKER #1 MONITOR SPEAKER #2

INPUT:

+1 Positive

-1 Negative

PARALLEL INPUTS

PARALLEL

CONNECTION

TO SECOND

MONITOR
SPEAKER

OR

INPUT:

+1 Positive

-1 Negative

PARALLEL INPUTS

WWW.WHARFEDALEPR O.COM

=NL4Connection

= ¼” Connection

INPUT:

+1 Positive

-1 Negative

PARALLEL INPUTS

WWW.WHARFEDALE PRO.COM

WWW.WHARFEDALE PRO.COM

NOTE7KLVFRQ¿JXUDWLRQUHSUHVHQWVDRKPORDGWRHDFKRXWSXWFKDQQHORIWKH

DPSOL¿HU

10

OPERATING MANUAL AND USER GUIDE

SPECIFICATIONS - Titan™ ACTIVE SERIES

System Type

Frequency Response (+/-3dB)

Low Frequency Driver (mm/in.)

High Frequency Driver

Exit Size (mm / inches)

Dispersion (H x V)

Impedance (ohms)

Amplifiers

Low Frequency (Class D)

High Frequency (Class A/B)

Electronic Crossover:

Crossover Frequency

Equalization:

Bass Response Optimizer (BRO™)

circuit

Subsonic Filter

Amplifier Protection

Power On

Thermal

Low Line Voltage Shut Down

Driver Protection

DC Protection

Short Protection

Clip Limiter:

Limiter Indicator

Power Indicator

Titan™ 8 ACTIVE

Active 8” 2-way Bi-Amplified

70-20kHz

205mm / 8”

Compression Driver

30mm / 1.2"

90° x 60°



Rated 150W RMS, 300W Peak

Rated 30W RMS, 60W Peak

24dB/octave Linkwitz-Riley

2.4kHz

30Hz, Second-order filter

Power switch on / off mute

Amplifier shutdown, auto reset

60% Nominal line voltage

Independent LF and HF limiters

Ye s

Ye s

Turns on approx 150W output

Red LED

Blue LED

Titan™ 12 ACTIVE

Active 12” 2-way Bi-Amplified

55-20kHz

305mm / 12”

Titanium Compression Driver

25mm / 1"

90° x 60°



Rated 250W RMS, 500W Peak

Rated 50W RMS, 100W Peak

24dB/octave Linkwitz-Riley

2.3kHz

High (±10dB) 10kHz Shelving

Low (±10dB) 100Hz Shelving

+5dB at 60Hz

30Hz, Second-order filter

Power switch on / off mute

Amplifier shutdown, auto reset

60% Nominal line voltage

Independent LF and HF limiters

Ye s

Ye s

Turns on approx 250W output

Red LED

Blue LED

Titan™ 15 ACTIVE

Active 15” 2-way Bi-Amplified

50-20kHz

381mm / 15”

Titanium Compression Driver

25mm / 1"

90° x 60°



Rated 350W RMS, 700W Peak

Rated 70W RMS, 140W Peak

24dB/octave Linkwitz-Riley

1.8kHz

High (±10dB) 10kHz Shelving

Low (±10dB) 100Hz Shelving

+5dB at 60Hz

30Hz, Second-order filter

Power switch on / off mute

Amplifier shutdown, auto reset

60% Nominal line voltage

Independent LF and HF limiters

Ye s

Ye s

Turns on approx 350W output

Red LED

Blue LED

23

Titan™ REAR PANEL LAYOUT

TM

INPUT:

+1 Positive

-1Ne gative

INPU TS

PARALLEL

POWERH ANDLING:

150W attsContinuous

300 WattsP rogram

500 Watts Peak

Impedance: 8 Ohms

INPUT:

+1Positi ve

-1Negative

POWERH ANDLING

00Watts Continuou

2

500Watts Program
1000Watts Peak
mpedanc e: 8 Ohms

I

:

s

WWW.WHARF EDALEPRO.COM

CONNECTION DIAGRAM #1

Titan™ 8/12/15 TWO - CHANNEL
SOUND SYSTEM CONNECTION

MIXER

AMP

INPUTS

MICROPHONES

MIXER OUTPUTS

AMPLIFIER OUTPUTS

Professional PowerAmplif i er

WWW.WHARFEDALEPRO.COM

WWW.WHARFEDALEPR O.COM

RIGHT SPEAKER

NL4

MODELS-SERIES

NL4

INPUT:

+1 Positive

-1 Negative

PARALLEL INPUTS

INPUT:

+1 Positive

-1 Negative

PARALLEL INPUTS

LEFT SPEAKER

8

OPERATING MANUAL AND USER GUIDE

SPECIFICATIONS - Titan™ SUB SERIES

System Type

Frequency Response (+/-3dB)

Enclosure Material

Enclosure Colour

Frame material

Size (mm / inches)

Coil Size (mm / inches)

Impedance

Speaker Pole Adapter

Inputs A & B - Type / Connection

Output A & B Type / Connection

Input Sensitivity

High Pass Frequency Selection

Phase Switch Selection

Crossover Frequency (HZ)

Speaker Level Input Impedance

Speaker Level Input Connection

Amplifier Power: Continuous

Amplifier Power: Peak

Power On Indicator

Power On Protection

Thermal Protection

Low Line Voltage Shut Down

Driver Protection

DC Protection

Short Protection

Clip Limiter:

Limiter Indicator

Power Indicator

Dimensions H x W x D: (mm)

Dimensions H x W x D (in)

Weight (Net) kg / lbs

TITAN™ Sub-A15

Band-pass subwoofer

45-150Hz

18mm Plywood

Grey or Black

Die-cast aluminium frame

404mm / 15”

75 / 3”

4 ohm

Ye s

Balanced Line Level inputs via two

combo connectors

Balanced Line Level inputs via two

combo connectors

0.775V

100Hz

0° / 180°

150

1/4” TS Phone input



400W

600W

LED

Power switch on / off mute

Amplifier shutdown, auto reset

60% Nominal line voltage

Independent LF limiters

Ye s

Ye s

Turns on approx 400W output

Red LED

Blue LED

630.0 x 478.0 x 640.0

24.8 x 18.8 x 25.2

45.48kg / 100.0lbs

Titan™ Sub-A12

Reflex subwoofer

55-200Hz

15mm MDF

Grey or Black

steel frame

305mm / 12”

64.26mm / 2.5”

4 ohm

Ye s

Balanced Line Level inputs via

two combo connectors

Balanced Line Level inputs via

two combo connectors

0.37V

150Hz

0° / 180°

80/ 100/ 120/ 150/ 180/ 200

(adjustable)

250W

500W

LED

Power switch on / off mute

Amplifier shutdown, auto reset

60% Nominal line voltage

Independent LF limiters

Ye s

Ye s

Turns on approx 250W output

Red LED

Blue LED

360.0 x 493 x 431.0

14.2 x 19.4 x 16.9

22.31kg /49.0lbs

25

FEATURES

ʍ

ʍ

ʍ

ʍ

ʍ

ʍ

ʍ

ʍ

ʍ

ʍ

ʍ

ʍ

ʍ

ʍ

ʍ

ʍ

ʍ

ʍ

ʍ

ʍ

2-way reflex systems

Passive (3) and Active (3) + Powered Subs (2)

Low distortion, high power woofers

25.4mm Titanium high frequency compression drivers

BRO™ Bass Response Optimizer (Titan™ 12/15 Active)

Class D Low Frequency Amplifier (Active)

Class A/B High Frequency Amplifier (Active)

XLR output for connecting to another powered speaker

RCA inputs for MP3, CD or other inputs

Integral Elliptical Wave Guide (EWG) 90° x 60°

Power On LED indicator in horn throat and back panel

Active signal limiting system with LED indicator

DTF™ Dynamic Thermal Filament HF driver protection (Titan

Light weight, high strength Polypropylene cabinet

Integral 35mm (1-3/8”) stand socket

M6, M8 hanging points

NL4 & 1/4” speaker inputs (Passive)

Combo XLR/ 1/4” input jacks (Active)

Internal crossover passive outputs (Sub-A12/15)

Accommodates OmniMount

®

60.0 bracket

™

8,12,15 Passive)

6

OPERATING MANUAL AND USER GUIDE

DIMENSIONS

15.83”

402mm



27.87”

708mm

2

18.81”

478mm

15.83”

402mm

8.7”

221mm

15.59"
396mm

2

10.47”

266mm

8.7"

221mm

27

WHAT ABOUT THE Titan™ SERIES?

Wharfedale Pro Titan™ Series of passive and self-powered foreground/back-ground music
and sound reinforcement speakers are designed for demanding professional applications
such as reproduction and reinforcement of music and sound in venues as diverse as live
performance venues, airports, houses of worship, A/V presentations, schools, retail shops,
restaurants and public houses.

The Titan™ Series loudspeakers are high quality speaker systems designed to provide the
best sound in a compact, feature laden, easy to use package. It is designed to provide
transparent and accurate sound reproduction or reinforcement. The 25mm Exit Titanium
high frequency drivers project crystal clear high frequencies . A proprietary 90° x 60°
Elliptical Wave Guide (EWG) delivers the high frequencies in a well defined, even coverage
pattern. Dynamic passages, such as the crack of a snare drum or the report of a cannon,
come through just like the real thing.

The Titan™ Series are also ideal in Audio/Visual applications. The rich accurate sound is a
great complement to any visual performance or presentation. Easy to transport and quick to
set up, the Titan™Active Series is the ideal choice for the serious professional.

Accessory wall brackets and rigging components available.

INTRODUCTION

Wharfedale Pro Titan™ Series loudspeakers are the result of many years of experience in

the use, design and manufacturing of professional loudspeaker products. We take great

pride in engineering and building every Wharfedale Pro loudspeaker and wish to thank you

for entrusting us with your sound.

From the time Gilbert Briggs built his first loudspeaker in 1932, to the present, Wharfedale

Loudspeakers have maintained the same standard of quality in components, workmanship

and performance. Actually, Wharfedale is one of a few present day manufacturers that

design, engineer and build all of their own transducers.

Please take a few minutes to read this manual completely in order to ensure that you get

the most out of your Titan™ Series Loudspeaker system.

4

OPERATING MANUAL AND USER GUIDE

DIMENSIONS

49

3.0

431.0

.0
60

3

TOP VIEW

463.0

FRONT VIEW

Titan SUB A12

360.0

431.

0

S

I

DE VIE

W

REAR VIE

Titan SUB A15

120Hz 150Hz

100Hz 180Hz

200Hz

80Hz

0

180

MAX

LOW
PASSFILTER

L

(BAL/UNBAL) (BALANCED)

R

AC220

240V50Hz

250W

INPUT

OUTPUT

FUSE

T3.15AL250V

W

29

LEFT SIDE VIEW

TOP VIEW

FRONT VIEW

OUTPUT

INPUT

(BALANCED)

(BALANCED)

0

I

I

I

I

I

I

A

I

I

WWW.WHARFEDALEPRO.COM

_

I

8

MAX

I

VOLUME

CAUTION

RISKOFELECTRICSHOCK

!

DONOTOPEN

THRU

0°

DONOTOPEN

WARNING:SHOCKHAZARD

180°

(100Hz)

-NEPASOUVRIR

AVIS:RISQUEDECHOCELECTRIQUE

HIGHPASS

SPEAKER

PHASE

LEVELIN

LIMIT

N2082

B

ON

(BALANCED) (BALANCED)

OFF

OUTPUT

INPUT

AC220-240V~50Hz400W

POWER

FUSET4AL250V

SERIALNUMBER

RIGHT SIDE VIEW BACK VIEW

IMPORTANT SAFETY INFORMATION POWERED PRODUCTS

Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been exposed to rain or moisture,
does not operate normally, or has been dropped.

This symbol indicates that there are
important operating and maintenance
instructions in the literature accompanying
this unit.

This symbol indicates that dangerous
voltage constituting a risk of electric shock
is present within this unit.

Read these instructions.
Keep these instructions.
Head all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the manufacturer's
instructions.
Do not install near any heat sources such as radiators,
heat registers, Stoves, or other apparatus(including
amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or
grounding type plug. A polarized plug has two blades
with one wider than the other. A grounding type
plug has two blades and a third grounding prong.
The wider blade or the third prong are provided for
your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the
obsolete outlet.

Protect the power cord from being walked on
or pinched, particularly at Plugs, convenience
receptacles, and the point where they exit from the
apparatus.

Use only attachments/accessories specified by the
manufacturer.

Unplug this apparatus during lightning storms or
when unused for long periods of time.

Refer all servicing to qualified service personnel.

Warning: To reduce the risk of fire or electrical
shock, do not expose this product to rain or moisture.
The product must not be exposed to dripping and
splashing and no object filled with liquids such as a
vase of flowers should be placed on the product.

No naked flame sources such as candles should be
placed on the product.

Caution: Changes or modifications not expressly
approved by the manufacturer could void the user's
authority to operate this device.

Warning: The mains power switch for this appliance
is located on the rear panel. To permit free access to
this switch, the apparatus must be located in an open
area without any obstructions.

ESSENTIAL INFORMATION FOR UK USERS
The power cord on your subwoofer may be supplied
with a plug incorporating a fuse, the value of which
is indicated on the pin face of the plug. Should the
fuse need to be replaced, an ASTA or BSI approved
BS1362 fuse must be used of the same rating. If the
plug is cut off it must NOT be re-used. Dispose of any
such plug safely. There is a danger of electric shock if
a cut-off plug is inserted into a mains socket.

The wires in the mains lead are coloured in
accordance with the following code: Green and
Yellow - Earth: Blue - Neutral: Brown - Live.
As the colours of the wires in the mains lead may
not correspond with the markings identifying the
terminals in the replacement mains plug, proceed as
follows:
The wire coloured Blue must be connected to the
terminal marked with the letter ¨N¨ or coloured
Black. The wire coloured Brown must be connected
to the terminal marked with the letter ¨L¨ or coloured
Red. The wire coloured Green and Yellow must be
connected to the terminal marked with the letter ¨E¨
, or coloured Green, or Green and Yellow, or marked
with the Earth symbol.

Use only with a cart, stand, tripod, bracket,

or table specified by the manufacturer, or

sold with the apparatus. When a cart is

used, use caution when moving the cart/

apparatus combination avoid injury from

tip-over.

2

Wharfedale Professional

IAG HOUSE Sovereign Court, Ermine Business Park Huntingdon, Cambs, PE29 6XU, England

Wharfedale Professional reserves the right to alter or improve specifications without notice

www.wharfedalepro.com

All rights reserved © 2008 Wharfedale Pro. Wharfedale Pro is a member of the International Audio Group (IAG).

ᥦ⠜ᮍᓣ

ᇕᑩ

28
26
24
22
20
18

16

14

12
10
8

6
4
2

ᇕ䴶

130
3
5

7

9
11
13
15

17
19
21
23

25
27

29