Wharfedale SI Series User Manual

SI SERIES LOUDSPEAKERS
INSTRUCTION MANUAL
WHARFEDALE SYSTEMS DIVISION
Unpacking
All Wharfedale Pro products are fully checked before leaving the factory. After unpacking please inspect cabinets for any physical
Operating/Use
1. The SI Series accept cables with Speakon™ and bare wire and
feature two Speakon™ type connectors and a barrier strip situated at the rear of each cabinet. These are connected in parallel. Take care to avoid adding too many SI speaker systems in series (this does not apply to 64T). Each series connected speaker increases the load on the amplifier and can add up to a total load that may exceed the amplifier’s capabilities, leading to possible damage. Two 8 loudspeakers in series make a 4total load. Four 8series connected loudspeakers make a total load of 2, which is too low for many amplifiers.
2. Attach the speaker cable securely to your SI Series unit and power amplifier (the amplifier should be off, power down mode). Where possible use Speakon™ connectors as they are professional high current connections specifically designed for this application. Try to use the correct type of speaker cable according to the handling ability of your SI Series Cabinet. Use 2 core equal stranded insulated cable for speaker runs. It is always advisable to use heavier conductor cables on longer runs.
3. If using Speakon™, insert the speakon and rotate 1/8 of a turn until locked in. If using the barrier strip ensure the correct phase connection and secure with a Pozi-drive™/flat head screw driver.
4. Power up amplifier with levels on zero. Confirm units are operating.
WARNING & SAFETY INSTRUCTIONS
1. READ INSTRUCTIONS carefully before operating this product.
2
.
RETAIN these instructions.
3. COMPLY WITH WARNINGS - All warnings and instructions for
this product should be adhered to.
4. USE WITH AMPLIFIERS - In order to avoid damage, it is advisable to establish and follow a pattern for turning on and off any sound system. With all system parts connected, turn on source equipment, tape decks, instruments, mixers, signal processors etc., BEFORE turning on your power amplifier. Many products output turn on and turn off transients that can damage speakers. By turning on your power amplifier LAST and making sure the amplifier’s input controls are at minimum any transients “upstream” of the amplifier are not amplified and passed to the speaker. Wait until all system parts have stabilised, then bring up amplifier controls to operating level. This should take no more than a few seconds. Similarly when shutting systems down, always turn down amplifier input controls and then turn off your amplifier BEFORE shutting down other components. Professional amplifiers often feature delayed turn on/off circuits to perform these functions for you automatically.
5. CABLES - Never use shielded or microphone cable for any speaker connection as this will not be heavy enough to handle the amplifier load and could cause damage to the complete system.
6.
  RIGGING • SUSPENDING • MOUNTING
The rigging, suspension or mounting of this speaker system can expose members of the public to serious health risks and even death. UNDER NO CIRCUMSTANCES ATTEMPT TO RIG, SUSPEND OR OTHERWISE MOUNT THIS SYSTEM UNLESS YOU ARE FULLY QUALIFIED AND CERTIFIED TO DO SO BY RELEVANT LOCAL, STATE AND NATIONAL AUTHORITIES. ALL RELEVANT SAFETY REGULATIONS MUST BE FOLLOWED. IF YOU ARE NOT PROPERLY
QUALIFIED OR DO NOT KNOW OF PERTINENT REGULATIONS, CONSULT QUALIFIED PERSONNEL FOR ADVICE AND ASSISTANCE.
The SI Series enclosures are fitted with M8 size threaded inserts. Use M8 bolts only in these inserts to suspend the enclosure. Make sure that you use forged shoulder eyebolts with a length of at least 30mm. Insert a flat washer between the eyebolt and the enclosure.
7.
CAUTION: These professional loudspeaker systems are
capable of generating very high sound pressure levels. Use care with placement and operation to avoid exposure to excessive levels that can cause permanent hearing damage.
8. SERVICING - The user should not attempt to service this product except that mentioned in this manual.
9. WARRANTY - In the event of malfunction, contact your authorised Wharfedale Professional dealer or distributor for further information. The SI Series from Wharfedale Professional is warranted against manufacturing defects and/or materials for a period of three years from the original date of purchase. During that period Wharfedale Professional will at its discretion repair or replace product provided that the product itself is returned with notice to an authorised Wharfedale dealer. Wharfedale Professional will not be held responsible for any defects(or any consequential damage) resulting from modifications made by unauthorised service agents, Acts of God, improper use of the equipment or negligence on the part of the user.
SI SERIES
SI SERIES LOUDSPEAKERS USER MANUAL
SI-10,SI-12, SI-15, SI-28, SI-15B, SI-18B
WHARFEDALE SYSTEMS DIVISION
SI SERIES
FEATURES OF THE SI SERIES:
Trapezoidal (SI-10 5 sided) Enclosure Design for multiple applications
Compact High Power Handling
Wharfedale Proprietary LF Driver
44mm Titanium Diaphragm true Compression Driver
Spherical Waveguide provides consistent control over HF coverage 70x70º and effective array coupling
15mm MDF Construction with tough industrial acrylic textured finish
Heavy duty steel foam backed grille
20 rigging/suspension mounting points (M8 thread)
Dual Speakon™ type and Barrier strip connectors
M8 Thread for Omnimount™ 100 type bracket
Available in black or white
FEATURES OF THE SI SERIES SUBWOOFERS:
Compact vented sub bass, low distortion, high effeciency
High output, extended excursion 18” (460mm) driver
15mm (SI-15B) or 18mm (SI-18B) MDF construction with tough acrylic textured pain
12 rigging/ mounting points (M8 Thread)
Dual Speakon™ type and Barrier strip connectors
Available in black or white
SI SERIES OVERVIEW:
The SI Series comprises of the SI-10, SI-12, SI-15 and SI 28 full range systems plus two subwoofers - the SI15B and the SI-18B.
SI-10, SI-12, SI-15 and SI 28:
All the full range models are two way systems with an internal passive crossover providing high level , high definition performance in a compact enclosure. With a nominal 70 degree coverage pattern, the system can be arrayed for additional coverage and SPL requirements. The elliptical waveguide HF section provides consistent coverage over its specified range for low feedback in open mic applications and improved array smoothness. M8 flypoints (20 in total) on the top, bottom and sides allow ease of installation in both horizontal and vertical positions. The unique 5 sided multi-angle shape of the SI-10 makes it perfect for low profile ceiling mounting (or corner installation) or as a compact floor monitor.
SI-15B, SI-18B Subwoofers:
The SI-15B and SI-18B are compact sub bass systems designed for use with the SI-15, SI-12 and SI-28 full range loudspeakers in applications where extended low frequency output and increased system headroom are required. These powerful systems are capable of delivering high sound pressure levels with very low distortion over sustained periods. Superior output in extreme conditions is maintained through the use of effective dissipation mechanisms, avoiding the loss of power compression often found in other systems.
SI-10
SPECIFICATIONS:
SYSTEM:
Power handling: 120watts RMS,240watts program, 480watts peak
Nominal Impedance: 8
Frequency response (+/-3dB): 65-20kHz
Sensitivity: 96 dB/1watt/1meter
Coverage: 70 x 70º
Maximum SPL (dB) ref Peak Power: 123dB
LF Driver: 10”
HF Section:
Coil Size: 44mm/1.7 inches
Exit Size: 25.4mm/1 inch
Diaphragm Material: Metal
Crossover Point: 2.3k
Enclosure Type: multi angle
Finish colour: black or white
Rigging : M8 x 20
Back Panel Connectors: Speakon™type x 2 and barrier strip
Dimensions mm HxWxD: 512 x 344 x 330
Dimensions inches HxWxD: 20.1 x 13.5 x 12.9
Weight: 14.36kg/32.3lbs
SI-12
SPECIFICATIONS:
SYSTEM: SI-12
Power handling: 250watts RMS,500watts program, 1000watts peak
Nominal Impedance: 8
Frequency response (+/-3dB): 55-20kHz
Sensitivity: 97 dB/1watt/1meter
Coverage: 70 x 70º
Maximum SPL (dB) ref Peak Power: 127dB
LF Driver: 12”
HF Section:
Coil Size: 44mm/1.7 inches
Exit Size: 25.4mm/1 inch
Diaphragm Material: Metal
Crossover Point: 2.3k
Enclosure Type: trapezoidal
Finish colour: black or white
Rigging : M8 x 20
Back Panel Connectors: Speakon™type x 2 and barrier strip
Dimensions mm HxWxD: 562 x 374 x 333
DIMENSIONS INCHES HXWXD: 22.1 X 14.7 X 13.1
Weight: 16.26kg/36.6lbs
SPL,1W /1M (dB)
Horizontal Directivity
2000Hz
330
300
270
110
100
90
80
70
60
10
500Hz
300
270
240
0
-10
-20
-30
-40
-50
Clio
Freq ue nc y Res po nse / Impedance
100
0
330
30
60
30
-10
-20
-30
-40
-50
Clio
150210
180
4000Hz
300
90
270
100
80
60
40
Impedance(ohm s)
20
100 0
1000Hz
60
120
330
300
270
90
240
0
-10
-20
-30
-40
-50
Clio
0
330
-10
-20
-30
-40
-50
Clio
210
180
30
8000Hz
60
90
270
100 00
30
150
300
330
200 00
60
120
0
90
0
30
-10
-20
-30
-40
-50
Clio
60
90
240
180
120
240
150210
180
120
150210
240
210
180
120
150
SI-15
SPECIFICATIONS:
SYSTEM:
Power handling: 300watts RMS, 600watts program, 1200watts peak
Nominal Impedance: 8
Frequency response (+/-3dB): 45-20kHz
Sensitivity: 98 dB/1watt/1meter
Coverage: 70 x 70º
Maximum SPL (dB) ref Peak Power: 129dB
LF Driver: 15”
HF Section:
Coil Size: 44mm/1.7 inches
Exit Size: 25.4mm/1 inch
Diaphragm Material: Metal
Crossover Point: 2.3k
Enclosure Type: trapezoidal
Finish colour: black or white
Rigging : M8 x 20
Back Panel Connectors: Speakon™type x 2 and barrier strip
Dimensions mm HxWxD: 640 x 452 x 396
Dimensions inches HxWxD: 25.1 x 17.8 x 15.6
Weight: 23.48kg/52.8lbs
SI-28
SPECIFICATIONS:
SYSTEM:
Power handling: 200watts RMS,400watts program, 800watts peak
Nominal Impedance: 8
Frequency response (+/-3dB): 70-20kHz
Sensitivity: 97 dB/1watt/1meter
Coverage: 70 x 70º
Maximum SPL (dB) ref Peak Power: 126dB
LF Driver: 2 x8”
HF Section:
Coil Size: 44mm/1.7 inches
Exit Size: 25.4mm/1 inch
Diaphragm Material: Metal
Crossover Point: 2.3k
Enclosure Type: trapezoidal
Finish colour: black or white
Rigging : M8 x 20
Back Panel Connectors: Speakon™type x 2 and barrier strip
Dimensions mm HxWxD: 675 x 284 x 280
Dimensions inches HxWxD: 26.5 x 11.5 x 11
Weight: 17.22kg/38.7lbs
SI-15B
SPECIFICATIONS:
SYSTEM:
Power handling:300watts RMS,600watts program, 1200watts peak
Nominal Impedance: 8 or 4
Frequency response (+/-3dB): 45-1kHz
Sensitivity: 98 dB/1watt/1meter
Maximum SPL (dB) ref Peak Power: 129dB.
System Frequency: 40Hz
Enclosure Type: Trapezoidal
Finish colour: black or white tough acrylic paint
Rigging : M8 x 12
Back Panel Connectors: Speakon™type x 2 and barrier strip
Dimensions mm HxWxD: 640 x 452 x 396
Dimensions inches HxWxD: 25.2 x 17.8 x 15.6
Weight: 25.1kg/56.4lbs
SI-18B
SPECIFICATIONS:
SYSTEM:
Power handling: 400watts RMS,800watts program, 1600watts peak
Nominal Impedance: 8 or 4
Frequency response (+/-3dB): 35-2kHz
Sensitivity: 99 dB/1watt/1meter
Maximum SPL (dB) ref Peak Power: 131dB.
System Frequency: 35Hz
Enclosure Type: Rectangular
Finish colour: black or white tough acrylic paint
Rigging : M8 x 12
Back Panel Connectors: Speakon™type x 2 and barrier strip
Dimensions mm HxWxD: 700 x 537 x 508
Dimensions inches HxWxD: 27.5 x 21.1x 20
Weight: 37.8kg/85lbs
Wharfedale International Limited, IAG House, Sovereign Court, Ermine Business Park, Huntingdon, Cambs, PE29 6XU, England
www.wharfedalepro.com
The information in this manual is subject to change without notice. All rights reserved © 2004 Wharfedale Pro. Wharfedale is a member of the International Audio Group (IAG).
WHARFEDALE SYSTEMS DIVISION
911.401
MODEL SI-28 SI-10 SI-12 SI-15 SI-15B SI-18B
FREQUENCY RESPONSE@+/- 3dB 70-20k 65-20kHz 55-20kHz 45-20kHz 45-1kHz 35-2kHz SENSITIVITY 1w@1m(dB) 97dB 96dB 97dB 98dB 98dB 99dB COVERAGE Horiz. 70° 70° 70° 70° - ­COVERAGE vert. 70° 70° 70° 70° - ­POWER HANDLING(watts) Continuous 200 120 250 300 300 400 Music 400 240 500 600 600 800 Peak 800 480 1000 1200 1200 1600 MAX SPL (dB) 126dB 123dB 127dB 129dB 129dB 131dB SYSTEM IMPEDANCE(Ω) 88888 or 48 or 4 NUMBER OF DRIVERS Woofer 211111 HF 1111- ­LF DRIVER Impedance(Ω) 48888 and 4 8 and 4 Driver size 8” 10” 12” 15” 15” 18” Magnet wt 1180/41.6” 1180/41.6 1345/47.4 2467/87.1 2120/74.8 2400/84.7 Coil size 50/2” 38.1/1.5” 63.5/2.5” 76.2/3” 65/2.5” 75/3” Frame material metal metal metal metal metal aluminium
die cast H F SECTION Impedance(Ω) 8888 Coil size 44/1.7” 44/1.7” 44/1.7” 44/1.7” Exit size 25.4/1” 25.4/1” 25.4/1” 25.4/1” Diaphragm material metal metal metal metal HF HORN Type waveguide waveguide waveguide wave guide CROSSOVER SECTION Effective x-over point 2.3k 2.3k 2.3k 2.3k System Fb 70Hz 65Hz 55Hz 45Hz 40Hz 35Hz ENCLOSURE TYPE Shape trapezoidal trapezoidal trapezoidal trapezoidal trapezoidal rectangle Volume L 32.1L 38.5L 54.5L 78.5L 78.5L 134L Paint colour black or white black or white black or white black or white black or white black or white Thickness(mm) 15mm 15mm 15mm 15mm 15mm 18mm Rigging and numbers M8 x 20 M8 x 20 M8 x 20 M8 x 20 M8 x 12 M8 x 12 Grille: Thickness(mm) 1.2 1.2 1.2 1.2 1.2 1.2 Type full steel full steel full steel full steel full steel full steel Foam behind grille yes yes yes yes yes yes Back panel: Input connector: Type -1 Speakon™ Speakon™ Speakon™ Speakon™ Speakon™ Speakon™ Number 222222 Type-2 barrier strip barrier strip barrier strip barrier strip barrier strip barrier strip Number 111111 Parallel with input connector yes yes yes yes yes yes PRODUCT DIMENSIONS
H(mm/inch) 675/26.5 512/20.1 562/22.1 640/25.1 640/25.2 700/27.5 W(mm/inch) 284/11.5 344/13.5 374/14.7 452/17.8 452/17.8 537/21.1 D(mm/inch) 280/11 330/12.9 333/13.1 396/15.6 396/15.6 508/20
WEIGHT
Kg 17.22 14.36 16.26 23.48 25.1 37.8 Lbs 38.7 32.3 36.6 52.8 56.4 85
APPLICATIONS: 2 way 2 way 2 way 2 way sub woofer sub woofer
Loading...