PM SERIES POWERED MIXERS:
PM500
PM600
PM500 RM
PM600 RM
!Warning – read all operating and service instructions that accompany this appliance! !Varning – läs alla användaroch serviceinstruktioner som medföljer enheten! !Atenção - leia todas as instruções de manutenção e de operação
que acompanham este aparelho! !AVVERTENZA – Leggere attentamente le istruzioni per il funzionamento e la
manutenzione fornite con l'unità! !Aviso: Lea todas las instrucciones de funcionamiento y de mantenimiento que se
adjuntan a este aparato!Vaara – lue kaikki laitteen mukana toimitetut käyttö- ja huolto-ohjeet! !Advarsel – læs alle
betjenings- og serviceanvisninger, der følger med produktet! !Waarschuwing – lees alle bedienings- en onder-
houdsinstructies die bij dit apparaat horen! !Vorsicht - Lesen Sie diese Bedienungsanleitung sorgfältig durch!
!Attention: Lisez attentivement les instructions avant d’utiliser ce produit!
FORSIKTIGHET: För att minska risken för elstötar bör man inte ta bort enhetens ytterhölje (eller det bakre skyddshöljet). Reparationer får bara genomföras av kvalificerade servicetekniker.
AVISO: Para reduzir o risco de choque eléctrico, não remova a tampa (ou a cobertura traseira). O usuário não deve
efectuar a manutenção. Deve pedir aos técnicos qualificados em manutenção.
ATTENZIONE: Per ridurre il rischio di scosse elettriche, non rimuovere la copertura (o il pannello posteriore). Le
operazioni di manutenzione devono essere eseguite esclusivamente da personale qualificato.
PRECAUCION: Con el fin de reducir el riesgo de sacudidas eléctricas, no desmonte la tapa (o la tapa posterior). El
mantenimiento no deberá ser realizado por el usuario, sino por el personal de mantenimiento cualificado.
WARNING: To reduce the risk of electric shock, do not remove cover (or back). No user servicing to qualified service personnel.
VAROITUS: Tulipalo- ja sähköiskuvaaran vähentämiseksi älä irrota suojusta (tai takapaneelia). Älä huolla laitetta
itse,anna huoltotyöt ammattitaitoisen huoltohenkilökunnan tehtäväksi.
FORSIGTIG: For at mindske risikoen for elektrisk stød må du ikke fjerne beklædningen (eller bagbeklædningen).
Reparationer må kun udføres af kvalificeret servicepersonale.
PAS OP: Om de kans op elektrische schokken te minimaliseren, dient u de afdekklep (of achterkant) niet te verwijderen. Onderhoud dient alleen te worden uitgevoerd door gekwalificeerd personeel.
VORSICHT: Um diee Gefahr eines elektrischen Schlages zu vermeiden darf die Abdeckung nicht entfernt werden.
Die Wartung des Gerätes sollte qualifiziertem Fachpersonal vorbehalten bleiben.
CAUTION: Pour réduire les risques d’électrocution, ne pas démonter le capot. La manipulation doit être effectuée
par un personnel agréé.
Wharfedale Professional Limited Warranty: The PM Series of Powered Mixers are warranted to be
clear of manufacturing or materials defects for a period of one year from the original date of purchase. In
the event of malfunction, contact your authorised Wharfedale Professional dealer of distributor. Be aware
that warranty details differ from country to country.
Unpacking: All Wharfedale Pro Products are fully checked before leaving the factory. After unpacking
please inspect the units for any physical damage. Please retain the shipping carton if possible and internal packing material in case the unit needs to be returned. Please check as soon as possible that the
unit is functioning. In the event of any damage please contact your dealer immediately so that a written
claim for damages may be made.
WARNING: DUE TO THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
UNIT TO RAIN OR MOISTURE.
PM Series Instruction Manual Page 1
WHARFEDALE PROFESSIONAL PM SERIES POWERED MIXERS
CONTENTS:
PAGE 3: INTRODUCTION
FEATURES PM500 AND PM600
GETTING STARTED WITH YOUR PM MIXER
PAGE 4: CHANNEL STRIP DESCRIPTION
PAGE 5: DIGITAL DELAY SECTION
MASTER CONTROL
PAGE 6: TAPE IN AND RECORD OUT
REAR PANEL PM500
PAGE 7: REAR PANEL PM600
PAGE 8: APPLICATIONS
PAGE 9: DIMENSIONS
PAGE 10: SPECIFICATIONS
PM Series Instruction Manual Page 2
WHARFEDALE PROFESSIONAL PM SERIES POWERED MIXERS
INTRODUCTION:
Congratulations on the purchase of your PM Series Powered Mixer from Wharfedale Professional. The
PM Series is available in a choice of two models - the PM 500 and the PM 600. These two mixers have
the same specifications except where noted in this manual. The PM Series powered mixers are available
as standard in a carpet covered wooden box. The RM version is also available for both models. The RM
version comes without the wooden box surround so that the unit can be rack mounted.
In order to get the most satisfaction from your PM mixers, please read this manual carefully.
GETTING STARTED:
1. Before you turn on the main power to the unit, ensure that the Master Output Control is in the OFF
position.
2. If you need to connect or disconnect any cables or units, make sur the Power is OFF before doing so.
3. Check that the voltage of the unit matches the AC voltage you will be operating with.
FEATURES:
FEATURES:
PM600 and PM600 RM
• Five Mic and six line input sockets
• Channel six features extra Tape In button
• Digital Delay Section
• Three Band EQ in Master Section
• Tape In
• Record Out
• EFX Return
• EFX Send
• Power On/Off on front of unit for ease of use
• Parallel speaker outputs on rear of unit
• Main line output on rear of unit
• Built in 230 watt power amplifier
• Two band channel EQ
• XLR plus 1/4” input sockets
• Fan cooling system
• Thermal protection
PM500 and PM500 RM
• Four Mic and five Line input sockets
• Channel five features Tape In Button
• Main line output on rear of unit
• Two band Channel EQ
• XLR plus 1/4” input sockets
• Digital Delay Section
• Record Out
• Built in 120 watt power amplifier
• Thermal protection
PM Series Instruction Manual Page 3
WHARFEDALE PROFESSIONAL PM SERIES POWERED MIXERS
CHANNEL STRIP DESCRIPTION PM500:
1. VOLUME: Determines volume level of the
channel in the mix.
2. LOW EQ: The LOW EQ control gives 15db of
boost or cut at 80Hz. By turning the knob to the
right (boost) instruments such as guitars can be
given more clarity, or vocals can be ‘warmed’.
Turning to the left (cut) will eliminate unwanted
low frequencies such as those caused by close
miking or excessive bass frequencies in instruments
3. HIGH EQ: The High EQ control gives 15dB
boost or cut at 12kHz. Turn to the right to add
clarity to high frequency components such as percussion. By turning to the left, high frequencies
such as ‘hiss’ are cut.
4. MIC/LINE INPUT: Connection can be made to
the MIC/LINE inputs with either XLR or 1/4” phono
jack. This connection can be either a microphone
or a line level signal.
5. EFX: Use this control to determine the signal
level to be sent to the built in digital delay effect
control.
1
2
3
5
4
CHANNEL STRIP DESCRIPTION PM600:
1. VOLUME: Determines volume level of the channel in the mix.
2. LOW EQ: The LOW EQ control gives 12dB of boost or cut at 100Hz. By turning the knob
to the right (boost) instruments such as guitars can be given more clarity, or vocals can be
‘warmed’. Turning to the left (cut) will reduce hum or unwanted background interference.
3. HIGH EQ: The High EQ control gives 12dB boost or cut at 8kHz. Turn to the right to add
clarity to high frequency components such as percussion. By turning to the left, high frequencies such as ‘hiss’ are cut.
4. MIC/LINE INPUT: Connection can be made to the MIC/LINE inputs with either XLR or
1/4” phono jack. This connection can be either a microphone or a line level signal.
5. EFX: Use this control to determine the signal level to be sent to the built in digital delay
effect control.
1
4
5
2
3
The LF control frequency has been carefully selected, allowing pleasing musical adjustment to
vocals or instruments without losing their natural balance. The HF control is similarly designed to
enable pleasing musical control without harshness or excessive mid range interference.
PM Series Instruction Manual Page 4
WHARFEDALE PROFESSIONAL PM SERIES POWERED MIXERS
MASTER SECTION DESCRIPTION PM500 AND PM600:
DIGITAL DELAY SECTION:
The built in digital delay will process the
signal from the input channels and feed to
the master output. The effects of digital
delay are controlled by:
TIME: This adjusts the internal time of the
delays. Turn to the right to increase the
interval time between two delays, turn to
the left to decrease.
REPEAT: This increases the repeat rate
of the delays by turning the knob to the
right.
VOLUME: This knob adjusts the mix level
of the effect.
PM600
PM500
MASTER CONTROL PM500:
The Master Control adjusts
the final level of the Main
bus signal which is output to
the speakers.
MASTER CONTROL PM600:
The Master Control on the
PM600 also offers a three band
(MID, LOW and HIGH) EQ
section for tonal adjustment of
the final mix.
PM Series Instruction Manual Page 5
WHARFEDALE PROFESSIONAL PM SERIES POWERED MIXERS
TAPE IN AND REC OUT PM500 AND PM600:
The TAPE IN sockets allow cassette
recorders or CD players to be added
to the Main output. The RECORD
OUTPUT provides a signal output to
a cassette deck and home audio
equipment. Sockets are RCA Phono.
REAR PANEL DESCRIPTION PM500:
PM500:
1. MAIN LINE OUT: This unbalanced insertion point allows the main output to be sent to an
external signal processor or power amplifier. The insert is a 1/4” phono jack socket which is not
bypassed.
2. SPEAKER OUTPUT JACKS: These outputs allow two speakers to be connected at the
same time to the powered mixer. The total minimum load required is 4 Ohms. If the total load is
less than 4 Ohms it may result in the mixer being damaged. The following guidelines should be
noted:
When using two speakers at the same time, use 8-16 Ohms speakers.
When using one speaker only, use a 4-8 Ohms speaker.
3. FUSE: Always ensure that the fuse is of the correct rating.
4. ALUMINIUM HEATSINK: This allows a cooling airflow through the unit. Make sure that the
heatsink is free from dust and there is sufficient room left at the back of the unit to allow the
heatsink to work efficiently.
PM Series Instruction Manual Page 6
1
2
3
4
WHARFEDALE PROFESSIONAL PM SERIES POWERED MIXERS
REAR PANEL DESCRIPTION PM600:
PM600:
1. MAIN LINE OUT: This unbalanced insertion point allows the main output to be sent to an
external signal processor or power amplifier. The insert is a 1/4' phono jack socket which is normally bypassed.
2. SPEAKER OUTPUT JACKS: These outputs allow two speakers to be connected at the
same time to the powered mixer. The total minimum load required is 4 Ohms. If the total load is
less than 4 Ohms it may result in the mixer being damaged. The following guidelines should be
noted:
When using two speakers at the same time, use 8-16 Ohms speakers.
When using one speaker only, use a 4-8 Ohms speaker.
3. FUSE: Always ensure the fuse is of the correct rating.
4. COOLING FAN: This creates a cooling airflow through the unit. Make sure that the fan is
free from dust and there is sufficient room left at the back of the unit to allow the fan to work
efficiently.
PM Series Instruction Manual Page 7
2
1
3
4
AUDIO CASSETTE
CD PLAYER
PM Series Instruction Manual Page 8
KEYBOARD
VOCAL MIC
GUITAR
SPEAKERS
Graphic EQ
Power Amplifier
WHARFEDALE PROFESSIONAL PM SERIES POWERED MIXERS
APPLICATIONS: PM600
WHARFEDALE PROFESSIONAL PM SERIES POWERED MIXERS
DIMENSIONS:
PM600
PM600 RM
PM500
PM500 RM
475mm/18.7” including carpet box
188mm
7.4”
241mm
9.5”
475mm/18.7” including carpet box
155mm
6.1”
269mm
10.5”
Front view
End view
Front view
End view
485mm/19” including rack mounts
145mm
5.7”
228mm
8.9”
Front view
End view
485mm/19” including rack mounts
112mm
4.4”
248mm
9.7”
Front view
End view
PM Series Instruction Manual Page 9
MODEL PM500 PM600
POWER AMP - MAX OUTPUT IN WATTS
4 OHMS 120 WATTS 230 WATTS
INPUTS
BALANCED MIC 4 5
LINE CHANNELS 5 6
INPUT IMPEDANCE
LOW Z (BALANCED) 2KOHMS 2KOHMS
LINE 16KOHMS 16KOHMS
MAIN OUT UNBAL. TRS UNBAL. TRS
FREQUENCY RESPONSE (+/-3dB) 20 to 25KHz 20 to 25KHz
MAXIMUM
CHANNEL
GAIN
LOW Z (BALANCED) 40dB 40dB
LINE 20dB 20dB
MAXIMUM
INPUT LEVEL
LOW Z (MIC) 0dB 0dB
LINE +20dB +20dB
MAXIMUM
OUTPUT LEVEL
MAIN +18dBv +18dBv
RECORD OUT +5dBv +5dBv
MASTER
EQ
HI EQ NA 12Khz±12DB
MID EQ NA 1Khz±12dB
LOW EQ NA 80Hz±12dB
PROTECTION THERMAL/LOAD THERMAL/LOAD
MASTER SECTION
BUILT IN DIGITAL EFFECT YES YES
THD LESS THAN 0.1% LESS THAN 0.1%
CHANNEL
EQUALISATION
LOW EQ 80Hz±15dB 100Hz±12dB
HI EQ 12kHz±15dB 8kHz±12dB
POWER CONSUMPTION 120 WATTS 230 WATTS
POWER REQUIREMENTS 160 WATTS 330 WATTS
SPEAKER CONNECTORS 1/4” JACK 1/4” JACK
WEIGHT
PM500 9.32KG/20.5lbs PM600 11.48KG/24.7lbs
PM500RM 7.6KG/16.7lbs PM600RM 9.72KG/21.4lbs
DIMENSIONS
PM500 475MM X 269MM X 155MM 18.7” x 10.5” x 6.1”
PM600 475MM X241MM X 188MM 18.7” x 9.5” x 7.4”
PM500RM 485MMX248MMX112MM 19” X 9.7” X 4.4”
PM600RM 485MMX228MMX145MM 19” X 8.9” X 5.7”
PM Series Instruction Manual Page 10
WHARFEDALE PROFESSIONAL
IAG HOUSE, SOVEREIGN COURT, ERMINE BUSINESS PARK
HUNTINGDON, PE29 6XU, UNITED KINGDOM
www.wharfedalepro.com
911.324
Loading...