Note: DVD instruction in this manual is just for the special models which have the DVD slot.
(DVD is only available in some models, please see the real)
Safety Notice
To prevent fire or electric shocks please read the instruction before
installing, using and cleaning the television.
l Please read all the instructions before operation;
l Please keep the manual for future reference ;
l Do not use any accessories that not recommended by manufacturer:
l Before operation, make sure the operating voltage of this unit is corresponds
with your house electricting supply;
l Do not place the unit on unstable, dusty and humid places;
l Never put the unit in direct sunlight or near heat sources;
l Allow enough space for proper ventilation;
l Please keep water away from the LCD-TV . If water comes in contact with the
LCD-TV, disconnect the power cord from the power source, then wipe the set
with a dry soft cloth;
l Do not remove the back cover. If services were need, please refer to
customer helpline.
(The description of the button may be different, just see the real.)
Control Panel Function
1. Standby switch
2.SOURCE Select the input signals: PC/COMPONENT/DVD/HDMI/
TV/SCART/S-VIDEO
3. MENU Press to select the main menu
4. VOL- Volume down / Left orientation to adjust the item in the OSD
VOL+ Volume up / Right orientation to adjust the item/Press to enter
5. CH- TV channel down / to select the item in the menu
CH+ TV channel up / to select the item in the menu
6. Power indicator
Illuminates red in standby mode, illuminates green when the display is
turned on
7.Remote Sensor
6
7
Customer helpline:0845 604 0105
Connection Options
DVD
STOP
PLAY/PAUSE OPEN/CLOSE
PREVNEXT
DVD insert
ANT IN
AUDIO IN
PrS-VIDEO
Pb
Y
TV SCARTVGA IN
Please see the real set of the
DVD position
VGA /COMPONENT/
SVIDEO Audio Input
Connect the PC output
connector from a PC to
the audio input port
ANT IN
AUDIO IN
Earphone port
Antenna Input
Connect cable or
antenna signals to
the TV, either direcÂtly or through your
cable box.
The above figure is for reference only,
connections may differ depending upon
the models
COMPONENT Input
Connect a component
video/audio
device to these jacks
SCART
Connect to the DVD/
VCR/broadcasting
receiver or other
equipment
PrS-VIDEO
Y
Pb
TV SCARTVGA IN
S-Video Input
Connect S-Video out
from an S-Video device
to the jacks.
Customer helpline:0845 604 0105
HDMI
HDMI
Connect to HDMI
output of other
equipment
HDMI
VGA Input
Connect to the VGA
15PIN analog output
connector of the PC
display card for PC
display purpose
Remote Control Key Functions(for TV/DVD Combi)
When using the remote control, aim it
towards the remote sensor on the TV
STANDBY
P.STD
SCANSWAP CALL
OPEN/CLOSE
10+
MUTE
1234
5678
SOURCE
MENU
SETUP
PLAY/ENTER
OK
SLOW
MIX
SIZE
-/---/--
DTV/DVD
P+
P-
PAUSE/STEP
EXIT
TITLE/PBC
i
D.CALL
TEXT
TIME
TUNE
PROGRAM
EPG
SUBTITLE
SEARCH
REPEAT
HOLD
MODE
Customer helpline:0845 604 0105
9900
NICAM
V-V+
ZOOMAUDIO
STOP
REVFWD . PREVNEXT
D.MENU
ANGLE
FAV
A-B
SUBCODE
REVEAL
(For TV/DVD Combi Models)
Buttons on the remote control
Stand By
DVD Open/close
Picture Mode
Scan
DVD 10+
Mute
Swap
Call Screen Display
Program Number
NICAM
Source Exchange
Digital Selector
DTV/DVD
Volume/Channel Selection
MENU
Zoom
DVD Audio
DVD STOP
Tune Menu Button
DVD SETUP
DVD PAUSE/STEP
DVD FAST REVERSE
DVD FAST FORWARD
DVD/DVB-T MENU
DVD NEXT
DVD PREVIOUS
Exit Screen Display
DVD PLAY/ENTER/DVB-T ok button
UP
LEFT
DOWN
DVD PROGRAM/ DVB-T EPG button
DVD /DVB-T Cursor Move button
DVD /DVB-T SUBTITLE
DVD ANGLE/ DVB-T favourite
DVD SEARCH
DVD A-B REPEAT
DVD TITLE/PBC/DVB-T information button
DVD SLOW
DVD CALL
TELETEXT BUTTONS
DVD REPEAT
RED button
Green button
Yellow button
Blue button
Fast text button in analog
signal
Function button in DVBT
(just reference the OSD)
RIGHT
Remote Control Key Functions(for TV only)
When using the remote control, aim it
towards the remote sensor on the TV
STANDBY
SLEEP
PCAUTO AD DISPLAY
Q.VIEW
NICAM
MUTE
1234
5678
SOURCE
MIX
SIZE
OK
-/---/--
P+
MENU
P-
MODE
TIMEINDEX
TEXT
INFO
DTV/TV
HOLD
EPG
SUBTITLE
EXIT
i
90
P.STD
V-V+
S SMZOOM
SUBCODE
REVEAL
D.MENU
FAV
Buttons on the remote control
Stand By
NICAM
Picture Mode
Switch to PC mode
Return the last watched program channel
Mute
Automatically adjust in PC mode
Call Screen Display
Program Number
Picture mode
Source Exchange
Digital Selector
DTV/TV
Volume/Channel Selection
MENU
Sound mode
Zoom
TELETEXT BUTTONS
DVB-T MENU
TEXT BUTTON
DVB-T EPG button
DVB-T ok button
DVB-T SUBTITLE
DVB-T Cursor Move button
DVB-T favourite
Exit Screen Display
DVB-T information button
RED button
UP
LEFT
DOWN
Green button
Blue button
Yellow button
RIGHT
(For TV Models)
Customer helpline:0845 604 0105
Note:
The instructions on this manual is just
take remote control forTV/DVD Combi
for example.
Remote Control Key Functions
Installing Batteries
1.Open the cover of the battery compartment at the back of the remote
control.
2.Insert two AA alkaline batteries in the compartment. (plus and minus poles to
respective mark)
3.Replace the cover of the battery compartment.
1
2
Precautions
Make sure that there is no
obstacle between the remote
controller and television set.
Keep the remote controller
away from heat source or
humid area to ensure
effective performance of
the remote controller.
3
As strong light may interfere the
signals, change your position to
operate the remote controller if
the television cannot be turned
on or off as you expect.
Make sure that two AA 1.5V alkaline
batteries are loaded. The batteries
must be of the same type. The batteries
must be located properly. The batteries
are not rechargeable.
Customer helpline:0845 604 0105
Connection Instructions
Grounding
Ensure that you connect the grounding / earth wire to prevent possible
electric shock. If grounding methods are not possible, have a qualified
electrician install a separate circuit breaker. Do not try to ground the
unit by connecting it to telephone wires, lightening rods, or gas pipes.
External Equipment Connections
Antenna Connection
- Antenna or Cable Service with a Cable Box Connections
- For optimum picture quality, adjust antenna direction if needed.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
wall antenna
socket
RF coaxial wire (75 ohm)
VHF antenna
UHF antenna
ANT IN
outdoor
antenna
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
ANT IN
To improve picture quality in a poor
signal area, purchase and install a
signal amplifier.
If the antenna needs to be split for two
TV s, install a 2-Way Signal Splitter
in the connections.
If the antenna is not installed properly,
contact your dealer for assistance.
NOTE: All cables shown are just for example.
Customer helpline:0845 604 0105
Be careful not to bend the bronze
wire when connecting the antenna.
Connection Instructions
VGA Input
You can use your LCD-TV as a monitor for your personal computer using a VGA
cable (not supplied).
Connection and use steps:
1.Read the user guide supplied with
your computer and ensure that it has
a VGA connector;
2.Make sure that the power of the LCD
-TV and the PC are off;
3.Connect a D type 15-pin VGA interface
cable ( not supplied ) to the VGA video
interface connector on the PC. Then
connect the other end to the PC video
interface connector on the back of the
LCD-TV.Tighten the screws on the VGA
connectors once they are firmly
connected;
4.Turn on the power of the LCD-TV first ,
and then turn on the power of the PC;
5.Press the SOURCE button to set the video
input mode of the LCD-TV to PC-RGB;
6.Check the image on your TV. There may be noise associated with the resolution,
vertical pattern, contrast or brightness in PC mode. If noise is present, change
the PC mode to another resolution, change the refresh rate to another rate or
adjust the brightness and contrast on the menu until the picture is clear. If the
refresh rate of the PC graphic card cannot be changed,change the PC graphic
card or consult the manufacturer of the PC graphic card.
Resolution
ModeResolution
VGA
SVGA
XGA
640*48031.5KHz60Hz
800*60037.9KHz60Hz
1024*76848.4KHz60Hz
VGA IN
Frame frequency (Hz)Line frequency (Khz)
Note: All above listed are subject to VESA Criteria.
YPbPr Input
How to connect
Connect the DVD video outputs (Y, PB, PR)
to the COMPONENT(Y, Pb, Pr) IN socks on
the TV and connect the DVD audio outputs
to the AUDIO IN jacks on the TV, as shown
in the figure.
NOTE: If your DVD player does not have
component video output, use S-Video.
How to use
1. Turn on the DVD player, insert a DVD.
2. Use the SOURCE button on the remote control to select
Customer helpline:0845 604 0105
Connection Instructions
COMPONENT (If connected to S-VIDEO,select the S-VIDEO external
input source.)
3. Refer to the DVD player's manual for operating instructions.
Component Input ports
To get better picture quality, connect a DVD player to the component
input ports as shown below.
S-VIDEO Input
- To avoid picture noise (interference), leave an adequate distance between the
VCR and TV
Connection and use steps:
1.Read the user guide supplied with your AV devices and ensure that it has
S-Video connectors;
2.Make sure that the power of the LCD-TV and the AV device are switched off;
Connection Option 1
Set VCR output switch to 3 or 4 and then
tune TV to the same channel number.
Connection Option 2
1. Connect the audio and S-VIDEO cables
from the VCR's output jacks to the TV
input jacks, as shown in the figure.
2. Insert a video tape into the VCR and
press PLAY on the VCR. (Refer to the
VCR owner s manual.)
3
.Turn on the power of the LCD-TV first ;
and then turn on the power of the AV
device;
4.Press the SOURCE button to set the video
.
input mode of the LCD-TV to SVIDEO
mode .
Customer helpline:0845 604 0105
2
1
VCR
Connection Instructions
SCART Input
1.Connect the scart lead from the external device(DVD
players, settop boxes or game consoles, to the TV SCART
socket.
2.Press SOURCE to select SCART mode.
3. Press Play button on external equipment and it should
appear on the screen.
HDMI Input
HDMI Devices
Connect the cable from the HDMI devices
to the TV HDMI, as shown in the figure.
How to use
1. Select the iHDMI source by using the SOURCE
button on the remote control.
2. Operate the corresponding external equipment.
Refer to external equipment operating guide.
SCART
External equipment
HDMI
TV
HDMI
HDMI Devices
Note: The audio cable included with the TV should be used when connected with PC/
COMPONENT/S-VIDEO.
Customer helpline:0845 604 0105
Loading...
+ 30 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.