Whalen TGXLGT46DW User Manual

LOT NUMBER:
DATE PURCHASED: / /

Genesis Gaming TheaterTM 3-in-1 Mixed Media TV Stand

Model # TGXLGT46DW

ADULT ASSEMBLY REQUIRED

If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our toll-free customer service number and have your
instructions and parts list ready to provide the model name, part name or factory number:

1-866-942-5362 8:30 a.m. - 4:30 p.m. PST, Monday - Friday

ONLINE: www.whalenfurniture.com EMAIL: [e-mail]

Video Instruction Guides

Go to http://whalen.showuhow.com
videos for assembling and installing your product. Enter the following
product number on the ShowUhow homepage.

to view step-by-step instructional

TGXLGT46DW

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE
READ AND KEEP FOR FUTURE REFERENCE.

Whalen Furniture Mfg., Inc. Page 1 Factory # 56-12089

Model # TGXLGT46DW

GENERAL INFORMATION, TIPS

MAXIMUM RECOMMENDED WEIGHT LOADS

MANUFACTURER: Whalen Furniture
CATALOG: Genesis Gaming TheaterTM 3-in-1 Mixed Media TV Stand (TGXLGT46DW)
DATE OF MANUFACTURE: January 2012
MADE IN CHINA

MAXIMUM LOAD 15 lb. (6.8 kg)

FITS UP TO MOST 54” FLAT PANEL TVs
MAXIMUM LOAD 135 lb. (61.2 kg)

FITS UP TO MOST 54” FLAT PANEL TVs
WITHOUT SWIVELING FLOATER
MAXIMUM LOAD 135 lb. (61.2 kg)

PLACE TV BEHIND STOPPER

MAXIMUM LOAD 50 lb. (22.7 kg)

THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY
WITH FLAT PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE
AND WEIGHT LIMITS. NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT
PANEL TVS OR EQUIPMENT. TO AVOID INSTABILITY, PLACE FLAT PANEL TV IN CENTRE
OF UNIT; CRT TVS, IMPROPERLY POSITIONED FLAT PANEL TVS, OR FLAT PANEL TVS
OR OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND WEIGHT LIMITS
COULD FALL OFF OR BREAK THE UNIT, CAUSING POSSIBLE SERIOUS INJURY.

1. Please read the Assembly Instructions prior to assembling this product.

2. Remove all hardware from box and sort by size.

3. Check to see that all hardware and parts are present BEFORE assembling.

4. Ask a friend to assist you with the assembly of this furniture.

5. To avoid damage, assemble the product on a sturdy, level and protective surface.

6. Please wait until all steps are completed before tightening bolts.

7. Make sure all bolts are tightly fastened before the unit is used.

This product is sold with Tip Restraint Hardware kit. You must install the Tipping Restraint
Hardware between the wall and the TV stand to prevent any accidents or damages. When
properly installed, this restraint can provide protection against the unexpected tipping of the
unit due to small tremors, bumps or climbing. The restraint is only a deterrent and is not a
substitute for proper adult supervision. Use of tip-over restraints may only reduce, but not
eliminate, the risk of tip-over.

and TRICKS

Whalen Furniture Mfg., Inc. Page 2 Factory # 56-12089

Model # TGXLGT46DW

LR

LL

Parts and Hardware List

Please read completely through the instructions and verify that all parts listed are present
before beginning assembly.

A- Top Shelf Frame (1) B- Bottom Shelf Frame (1) C- Left Front Post (1)

D- Right Front Post (1) E- Spine (1) F- Wood Back Support (2)

G- Top Glass (1) H- Glass Shelf (2) I- Swiveling Floater Post (1)

J- Swiveling Bracket (1) K- XYZ Mounting Frame (1) L- Monitor Bracket (2)

M- SSS Spine (1) N- Sensor/Sound shelf (1) O- Gaming Guitar Clip (1) P- Cable Wheel (2)

(1) Suction Cup (14+1 extra) (2) 1/2” Bolt (8+1 extra) (3) 3/4” Bolt (17+1 extra)

Whalen Furniture Mfg., Inc. Page 3 Factory # 56-12089

Model # TGXLGT46DW

Parts and Hardware List

Please read completely through the instructions and verify that all parts listed are present
before beginning assembly.

(4) 1” Bolt (8+1 extra) (5) 1-1/4” Bolt (6+1 extra) (6) 2-1/4” Bolt (4+1 extra)

(7) Lock Washer (38+1 extra) (8) Flat Washer (38+1 extra) (9) Glass Clamp w/Bolt (4+1 extra)

(10) Concrete Anchor (11) 2-1/2” Lag Bolt (12) Lag Bolt Washer (13) Acrylic Stopper

(4) (4) (4+1 extra) (1)

M4 Allen Wrench 3/16” Allen Wrench Touch-up Pen Tipping Restraint Hardware Kit (1)

(2) (1) (1) (Inside Plastic Bag)

TV Mounting Kit

M4 x 12 Bolt (4) M4 x 30 Bolt (4) M5 x 12 Bolt (4) M5 x 30 Bolt (4)

M6 x 12 Bolt (4) M6 x 35 Bolt (4) M8 x 16 Bolt (4) M8 x 40 Bolt (4)

M4 Lock Washer (4) M5 Lock Washer (4) M6 Lock Washer (4) M8 Lock Washer (4)

Large Spacer (4) Small Spacer (4) M4/M5 Flat Washer (8) M6/M8 Flat Washer (4)

Tools required: Allen Wrench (provided) and Phillips Screwdriver (not provided).

Whalen Furniture Mfg., Inc. Page 4 Factory # 56-12089

E

UP

B

A

Lock Washer

(4 used in this step)

⑦

Flat Washer

(4 used in this step)

⑧

1-1/4” Bolt

(4 used in this step)

⑤

Note: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled,
go back and fully tighten all bolts. This will make it easier during assembly of unit.

1. Unpack the unit and confirm that you have all the hardware and required parts listed.

2. Locate Spine (E) and set back facing down on a scratch free surface as shown.

3. Align and attach Top and Bottom Shelf Frame (A and B) to the Spine (E). Make sure the flush

Whalen Furniture Mfg., Inc. Page 5 Factory # 56-12089

edges will face up after assembly.

Model # TGXLGT46DW

Assembly Instructions

B

A

C

Lock Washer

(8 used in this step)

⑦

Flat Washer

(8 used in this step)

⑧

1-1/4” Bolt

(2 used in this step)

⑤

3/4” Bolt

(6 used in this step)

③

4. Align and attach Left and Right Front Posts (C and D) to the front corners of Shelf Frames (A
and B). Make sure the gaps and offsets between the wooden front rail of Top Shelf Frame (A)
and the Posts are equal. Loosen the bolts on the end brackets and wooden front rail and
adjust if necessary.

Whalen Furniture Mfg., Inc. Page 6 Factory # 56-12089

Model # TGXLGT46DW

Assembly Instructions

Lock Washer

(8 used in this step)

⑦

Flat Washer

(8 used in this step)

⑧

1” Bolt

(8 used in this step)

④

UP

BACK

F

F

A/B

B

A

5. Stand the unit upright.

6. Attach 2 Wood Back Supports (F) to the back rail of Metal Frames. Make sure all the threaded
inserts for Glass Clamps are level with each other.

Whalen Furniture Mfg., Inc. Page 7 Factory # 56-12089

Assembly Instructions

Model # TGXLGT46DW

If you choose Table-top configuration,

continue to STEP 7.

If mounting TV with the Swinging Floater,

skip ahead to PAGE 12.

3/4” Bolt

(5 used in this step)

③

O

E

P

E

3

E

7. Attach 2 Cable Wheels (P) onto the backside of Spine (E). You can use the cable wheels to help
keep your entertainment center’s cables and cords organized.

8. Attach Gaming Guitar Clip (O) horizontally onto the backside of Spine (E). The Gaming Guitar
Clip can provide storage of gaming guitar controllers.

Whalen Furniture Mfg., Inc. Page 8 Factory # 56-12089

Model # TGXLGT46DW

Assembly Instructions

Model # TGXLGT46DW

Glass Clamp w/Bolt
(4 used in this step)

⑨

Suction Cup

(14 used in this step)

①

G

C/D

C/D/F

9

H

9

9

H

H

A

Assembly Instructions

9. Go back and tighten all bolts with the Allen Wrench provided.

10. Put the Suction Cups (1) firmly into the top holes of Top and Bottom Shelf Frames (A and B).
Attach the Glass Clamps (9) to the threaded inserts on both Front Posts (C and D) and Wood
Back Supports (F). Make sure you place the Glass Clamps in the same level so the shelf is not
tilted and set screw on each Glass Clamp is bottom.
Tip: If a suction cup resists insertion, try pressing down on the middle of the cup with the Allen
Wrench while twisting it clockwise into the hole.

11. Properly install the Top Glass (G) and Glass Shelves (H) with the black side of glass down.
Rotating clockwise the Set Screw underneath Glass Clamps to secure the Middle Glass Shelf in
place and to prevent falling easily and getting damage.

12. In case of uneven floor, Floor Levelers are provided at the bottom of both Front Posts (C and D).

Simply tilt the unit back and raise or lower floor leveler by hand to correct tilting.

Note: If glass is scratched you can minimize the damage by using a BLACK marker and filling in
scratched area from underneath.

Whalen Furniture Mfg., Inc. Page 9 Factory # 56-12089

Model # TGXLGT46DW

13

13

G

Acrylic Stopper

(1 used in this step)

⑬

Assembly Instructions

13. Remove the tape of Acrylic Stopper (13) and place it on the cut-out of the warning label on the

front of Top Glass (G). Make sure it is aligned before applying pressure.

14. Remove the warning label for Acrylic Stopper carefully.

NOTE: You must install the Acrylic TV Stopper to prevent TV from tipping when placing your
flat panel television directly on the table-top console.

Whalen Furniture Mfg., Inc. Page 10 Factory # 56-12089

Model # TGXLGT46DW

Assembly Instructions

15. Position the assembled Table-top in your desired location against the wall. Now follow the

instructions printed on the plastic bag containing the Tipping Restraint Hardware to mount the
tipping restraint to one Wood Back Support (F) and the wall.

NOTE: YOU MUST USE THIS TIPPING RESTRAINT TO ATTACH THIS UNIT TO
THE WALL, TO PREVENT ACCIDENTS AND/OR INJURIES.

16. The Table-top is ready for use now. Be sure to position your TV in center of console.

NOTE: For Wall Mount, proceed to PAGE #22.

Tools required: Allen Wrench (provided), Phillips Screwdriver, Mallet, Power Drill, and 3/8” Drill Bit.

Whalen Furniture Mfg., Inc. Page 11 Factory # 56-12089

Lock Washer

(4 used in this step)

⑦

Flat Washer

(4 used in this step)

⑧

Assembly Instructions for

Floating Swivel Mount

2-1/4” Bolt

(4 used in this step)

⑥

E

I

B

A

17. Align and attach the Swiveling Floater Post (I) to the back of Spine (E). Make sure the sockets

for Cable Wheel facing backward.

Whalen Furniture Mfg., Inc. Page 12 Factory # 56-12089

Model # TGXLGT46DW

Model # TGXLGT46DW

Lock Washer

(6 used in this step)

⑦

Flat Washer

(6 used in this step)

⑧

3/4” Bolt

(6 used in this step)

③

I

Assembly Instructions

18. Align and attach the Swiveling Bracket (J) to the top of Swiveling Floater Post (I) making sure

the pivoting bolt head is up. Tighten the bolts with enclosed M4 Allen Wrench.

Whalen Furniture Mfg., Inc. Page 13 Factory # 56-12089

Model # TGXLGT46DW

Lock Washer

(4 used in this step)

⑦

Flat Washer

(4 used in this step)

⑧

1/2” Bolt

(4 used in this step)

②

Assembly Instructions

19. The Sensor/Sound Shelf (N) provides two options: position gaming accessories above TV or

sound bar below TV. Choose the option you prefer, slide SSS Spine (M) onto the XYZ
Mounting Frame (K) properly. Adjust the height of SSS Spine and attach in place. Make sure
the Sensor/Sound Shelf (N) will not hit your TV.

Whalen Furniture Mfg., Inc. Page 14 Factory # 56-12089

Model # TGXLGT46DW

Lock Washer

(4 used in this step)

⑦

Flat Washer

(4 used in this step)

⑧

1/2” Bolt

(4 used in this step)

②

K

I

J

7

8

7

8

7

8

Assembly Instructions

20. Hold and attach the flat side of XYZ Mounting Frame (K) onto the Swiveling Bracket (J). Make

sure the recess holes on the XYZ Mounting Frame are at the bottom. Securely tighten with
enclosed Allen Wrench.

Whalen Furniture Mfg., Inc. Page 15 Factory # 56-12089

Model # TGXLGT46DW

Assembly Instructions

21. Pick up Sensor/Sound Shelf (N) and securely fit the back tabs into the small slots of SSS

Spine (M). Tighten both lock bolts pre-attached on the SSS Spine with a Phillips Screwdriver
until they hit the back tabs of Sensor/Sound Shelf.

Whalen Furniture Mfg., Inc. Page 16 Factory # 56-12089

Model # TGXLGT46DW

Mounting Monitor Brackets to a television with a flat back

Note: For televisions with a curved back or recessed back proceed directly to step #24.

22. Determine the correct diameter of the bolt your TV requires by hand threading them into the

threaded insert on the back of the TV. If you encounter any resistance, stop immediately. If
you are unable to find the correct bolt consult a local hardware store.

23. Follow the appropriate diagram below to attach Monitor Brackets (LL/LR) to the back of your

TV with selected fasteners. Make sure the Monitor Brackets are centered and level with each
other. Secure the bolts with a Phillips Screwdriver. DO NOT over tighten the bolts.

Note: Lean the TV up against a wall or other solid surface when attaching with the Monitor
Brackets. DO NOT place the TV face down on the glass this may cause permanent damage.

Whalen Furniture Mfg., Inc. Page 17 Factory # 56-12089

Model # TGXLGT46DW

Mounting Monitor Brackets to a television with a curved / recess back

24. Determine the correct diameter of the bolt your TV requires by hand threading them into the

threaded insert on the back of the TV. If you encounter any resistance, stop immediately. If
you are unable to find the correct bolt consult a local hardware store.

25. Follow the appropriate diagram below to attach Monitor Brackets (LL/LR) to the back of your

TV with selected fasteners. Make sure the Monitor Brackets are vertically centered and level
with each other. Secure the bolts with a Phillips Screwdriver. DO NOT over tighten the bolts.

Whalen Furniture Mfg., Inc. Page 18 Factory # 56-12089

DL/DR

Model # TGXLGT46DW

Assembly Instructions for Floating Swivel Mount

MAKE SURE ALL BOLTS ARE TIGHT AND SPINE IS AT A 90 DEGREE ANGLE AND USING
A QUALITY LEVEL TO VERIFY THE MOUNTING FRAME IS LEVEL PRIOR TO
INSTALLATION OF TV.

26. Once the Monitor Brackets (LL/LR) are attached onto the back of television, ask for assistance

to lift the television up to attach the Monitor Brackets onto the XYZ Mounting Frame (K). Set
the hooks on Monitor Brackets over the Mounting Frame then lower them onto the bars of
Mounting Frame. Loosen the Lock Bolt pre-attached on the Monitor Brackets to ensure an
easy fit at the bottom hooks. Proceed to center the television.

27. Once the television is in place, tighten both Lock bolts with a long Phillips Screwdriver until

they hit underside of XYZ Mounting Frame (K) to ensure your TV is safe and secure.

Whalen Furniture Mfg., Inc. Page 19 Factory # 56-12089

Model # TGXLGT46DW

Assembly Instructions for Floating Swivel Mount

28. The Monitor Brackets (LL/LR) can tilt up to 11˚ downward and 5˚ upward, depending on your

optimum viewing position. Have your assistant hold the TV steady before you start to adjust
the tilt. Simply reach behind the TV and turn the both Tilt Adjustment Knobs with enclosed
3/16” Allen Wrench to adjust your TV to provide optimum viewing and minimize glare.

Whalen Furniture Mfg., Inc. Page 20 Factory # 56-12089

Model # TGXLGT46DW

Assembly Instructions

29. Repeat steps 7 thru 12 to attach the Gaming Guitar Clip (O) and Cable Wheels (P) onto

the Swiveling Floater Post (I) and install Top Glass (G) and Glass Shelves (H) into place.

30. Carefully move the console and position in your desired location against a wall. Now follow the

instructions printed on the plastic bag containing Tipping Restraint Hardware Kit to mount the
tipping restraint to the Swiveling Floater Post (I) and the wall.

Note: You must install the Tipping Restraint Hardware with the unit in use to prevent any
accidents or damage to the unit.

31. You can enjoy your home entertainment center now. Swivel left-or-right for optimum viewing

control.

Tools required: Allen Wrench (provided), Phillips Screwdriver, Mallet, Power Drill, and 3/8” Drill Bit.

Whalen Furniture Mfg., Inc. Page 21 Factory # 56-12089

Model # TGXLGT46DW

The following steps are only for those who wish to mount their
TV directly to the wall. If you have already mounted your TV to
the Swinging Floater or plan to display your TV on the top
surface of the stand, disregard the following steps.

Do not over tighten the Lag Bolts. Tighten Lag Bolts only until the Lag
Bolt Washer is pulled firmly against the metal plate of Mounting Frame. If there is a layer
of drywall or other material, this drywall or other material may not exceed 5/8 inch in
thickness. Failure to heed this caution may result property damage and/or personal injury.

Assembly Instructions for Universal Wall Mount

NOTE: If you are mounting your TV onto brick, solid concrete or concrete block, skip this
section. This assembly requires an electric drill, level and stud finder (not included).

32. Using a stud finder, locate the edges of the wood studs. Find the center line of each stud and
draw a vertical reference line on the wall over each one. Place the XYZ Mounting Frame (K)
level against the wall where you intend to mount the TV. Using the Mounting Frame (K) as a
template, mark 4 drill points (2 on top, 2 on bottom) with a pencil on the vertical reference lines
you just drew.

33. With an electric drill (not included) drill 3/16 inch diameter holes to at least 2½ inch deep on
the four drill points. While holding the Bracket Plate in place, loosely screw in the Lag Bolts (11).

34. Secure the XYZ Mounting Frame (K) to wall with Lag Bolts (11) and washers (12) at the drill
points. Tighten bolts firmly, but be careful not to over tighten.

Installing XYZ Mounting Frame onto WOODEN STUD WALL

Whalen Furniture Mfg., Inc. Page 22 Factory # 56-12089

Assembly Instruction for installing XYZ Mounting Frame onto BRICK, SOLID

Concrete Anchors should only be used for masonry mounting.

NEVER use the wall anchors to mount the unit to drywall.

Maximum weight 135 lb. (61.2 kg)

CONCRETE OR CONCRETE BLOCK

NOTE: If you are mounting your TV to a wall with wooden studs, skip this section.
This assembly requires an electric drill and level (not included).

35. Begin by placing the XYZ Mounting Frame (K) level against the wall where you intend to

Whalen Furniture Mfg., Inc. Page 23 Factory # 56-12089

mount the TV. Using the Mounting Frame (K) as a template, mark 4 drill points with a pencil.

36. With an electric drill (not included) on its low setting, drill 7/16 inch diameter holes to at least
2½ inch deep. Insert Concrete Anchors (10) into pre-drilled holes so that they are flush with
the wall.

37. Place the XYZ Mounting Frame (K) level in the desired position against the wall. Secure the
Mounting Frame (K) to wall with Lag Bolts (11) and washers (12) at the drill points. Tighten
bolts firmly, but be careful not to over tighten.

Model # TGXLGT46DW

K

LR

LL

K

M

N

DL/DR

Model # TGXLGT46DW

Assembly Instructions

38. The Sensor/Sound Shelf (N) provides two options: position gaming accessories above TV or
sound bar below TV. Choose the option you prefer, slide SSS Spine (M) onto the XYZ
Mounting Frame (K) properly. Adjust the height of SSS Spine and attach in place. Make sure
the Sensor/Sound Shelf (N) will not hit your TV.

39. Once the Monitor Brackets (LL/LR) are attached onto the back of television, ask for assistance
to lift the television up to attach the Monitor Brackets onto the XYZ Mounting Frame (K). Set
the hooks on Monitor Brackets over the Mounting Frame then lower them onto the bars of
Mounting Frame. Proceed to center the television.

40. If you want to adjust the tilt, ask for help from your friends to hold the TV steady before you
start to adjust. Simply turn the both Tilt Adjustment Knobs on Monitor Brackets (LL/LR) with
3/16” Allen Wrench to adjust your TV to provide optimum viewing and minimize glare. When
the TV is in its intended position, tighten both Lock bolts with a long Phillips Screwdriver until they hit
underside of XYZ Mounting Frame (K) to ensure your TV is safe and secure on the wall.

41. Repeat step 21 to install Sensor/Sound Shelf (N) onto the SSS Spine (M).

42. Place assembled console under your TV set as shown below. Finally, connect the A/V and
power cables to your TV. You are now ready to enjoy your wall-mounted Flat Panel TV.

Whalen Furniture Mfg., Inc. Page 24 Factory # 56-12089

Model # TGXLGT46DW

Care and Maintenance

 Use a soft, clean cloth that will not scratch the surface when dusting.
 Use of furniture polish is not necessary. Should you choose to use polish, test first in an

inconspicuous area.

 Using solvents of any kind on your furniture may damage the finish.
 Never use water to clean your furniture as it may cause damage to the finish.
 Always use coasters under beverage glasses and flowerpots.
 Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid

rubbing.

 Always use protective pads under hot dishes and plates. Heat can cause chemical changes that

may create spotting within the furniture finish.

 Stains or marks from crayons or ink markers will be difficult to remove.
 In the event that your furniture is stained or otherwise damaged during use, we recommend that

you call a professional to repair your furniture.

 Check bolts/screws periodically and tighten them if necessary.

Further advice about furniture care

It is best to keep your furniture in a climate-controlled environment. Extreme temperature and
humidity changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep
furniture away from direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important
and helpful tips will enhance your furniture as it ages.

A Touch-up Pen has been provided to repair any small nicks or scratches that may occur
during assembly or shipping.

We hope you enjoy your purchase for many years.

Thank you for your purchase!

We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will

repair or replace it for up to one (1) year from the date of purchase. Every Whalen Furniture
product is designed to meet your highest expectations. We guarantee that you will
immediately see the value of our fine furniture.

This warranty gives you specific legal rights and you may also have other rights which vary
from State to State (province to province).

Customer Service: 1-866-942-5362

8:30 a.m. - 4:30 p.m. PST, Monday to Friday

Whalen Furniture Mfg., Inc. Page 25 Factory # 56-12089

QUALITY GUARANTEE

www.whalenfurniture.com

IF YOU NEED TO ORDER PARTS PLEASE USE THE LIST BELOW

Genesis Gaming Theater

TM

3-in-1 Mixed Media TV Stand (TGXLGT46DW)

*TGXLGT46DW-1-SFP Swiveling Floater Post *TGXLGT46DW-20-CW Cable Wheel

*TGXLGT46DW-2-LEC Large End Cap (40 x 60 mm) *TGXLGT46DW-21-GGC Gam ing Guitar Clip

*TGXLGT46DW-3-TG Top Glass *TGXLGT46DW-22-FL Floor Leveler

*TGXLGT46DW-4-GS Glass Shelf *TGXLGT46DW-23-OPG Oval Plastic Grommet

*TGXLGT46DW-5-LFP Left Front Post *TGXLGT46DW-24-1/2B 1/2” Bolt

*TGXLGT46DW-5B-LFPWD Left Front Post Wood Decoration *TGXLGT46DW-25-3/4B 3/4” Bolt

*TGXLGT46DW-6-RFP Right Front Post *TGXLGT46DW-26-1B 1” Bolt

*TGXLGT46DW-6B-RFPWD Right Front Post Wood Decoration *TGXLGT46DW-27-1 1/4B 1-1/4” Bolt

*TGXLGT46DW-7-MF Mounting Frame *TGXLGT46DW-28-2 1/4B 2-1/4” Bolt

*TGXLGT46DW-8-RMB Right Monitor Bracket *TGXLGT46DW-29-LW Lock Washer

*TGXLGT46DW-9-LMB Left Monitor Bracket *TGXLGT46DW-30-FW Flat Washer

*TGXLGT46DW-10-TAK Tilt Adjustment Knob *TGXLGT46DW-31-GCB Glass Clamp w/Bolt

*TGXLGT46DW-11-LB Lock Bolt *TGXLGT46DW-32-CA Concrete Anchor

*TGXLGT46DW-12-SB Swiveling Bracket *TGXLGT46DW-33-2 1/2LB 2-1/2” Lag Bolt

*TGXLGT46DW-13-SSSS SSS Spine *TGXLGT46DW-34-LFW Large Flat Washer

*TGXLGT46DW-14-SSS Sensor/Sound Shelf *TGXLGT46DW-35-SC Suction Cup

*TGXLGT46DW-15-S Spine *TGXLGT46DW-36-M4AW M4 Allen Wrench

*TGXLGT46DW-16-SEC Sm all End Cap (20 x 60 mm) *TGXLGT46DW-37-3/16AW 3/16” Allen Wrench

*TGXLGT46DW-17-TSF Top Shelf Frame *TGXLGT46DW-38-TRHK Tipping Restraint Hardware Kit

*TGXLGT46DW-17A-TSWM Top Shelf Wood Molding *TGXLGT46DW-39-TUP Touch-up Pen

*TGXLGT46DW-18-BSF Bottom Shelf Frame *TGXLGT46DW-40-AS Acrylic Stopper

*TGXLGT46DW-18A-BEC Bottom End Cap (20 x 20 mm) *TGXLGT46DW-TVMK TV Mounting Kit

*TGXLGT46DW-19-WBS Wood Back Support *TGXLGT46DW-CH Complete Hardware