Whalen PAR2PST Assembly Manual

/ /

Parker 2-pk Stools
Stock # PAR2PST

LOT NUMBER:
DATE PURCHASED:

If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions and
parts list ready to provide the model name, part name or factory number:

1-866-942-5362

Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday to Friday

Or visit our web site 24 hours a day, 7 days a week for product assistance at

www.whalenstyle.com

Or e-mail your request to [e-mail]

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT
PLEASE READ AND KEEP FOR FUTURE REFERENCE.

Whalen Furniture Manufacturing Page 1 Factory No. 16650

Date 2014-11-24 Rev. 1 Factory: GOSHWO

SAFETY INFORMATION.

ADULT ASSEMBLY REQUIRED

Stock # PAR2PST

QUALITY GUARANTEE

We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair

or replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed
to meet your highest expectations. We guarantee that you will immediately see the value of our fine
furniture.

This warranty gives you specific legal rights and you may also have other rights which vary from State
to State.

Customer Service: 1-866-942-5362

8:30 a.m. - 4:30 p.m., PST, Monday to Friday

www.whalenstyle.com

1. Maximum load weight on chair is 136 kg (300 pounds).

MAXIMUM RECOMMENDED WEIGHT LOADS

THIS UNIT IS INTENDED FOR USE ONLY WITH THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM
WEIGHTS INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.

GENERAL INFORMATION, TIPS & TRICKS

1. Please read the Assembly Instructions prior to assembling the unit.

2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface.

3. Keep all hardware and parts out of the reach of children.

4. Please wait until all steps are completed before fully tightening bolts.

5. Make sure all bolts and screws are tightly fa stened before the unit is used.

6. Check that all bolts, screws and knobs are tight at least every 3 months or as needed.

Please call for replacement parts or assistance:

1-866-942-5362

Whalen Furniture Manufacturing Page 2 Factory No. 16650

Stock # PAR2PST

Parts and Hardware List

Please read completely through the instruction s and v erify that all listed parts and hardware are present
before beginning assembly.

A- Chair Backrest (2) B- Seat Frame with Cushion (2)

C- Left Front Leg (2) D- Right Front Leg (2)

E - Left Side Stretcher (2) F - Right Side Stretcher (2) G- Front Stretcher (2)

(1) Ø5/16" x 1-1/2” Bolt (4+1 extra) (2) Ø5/16" x 3-1/4” Bolt (8+1 extra)

(3) Ø5/16" Hex Nut (4) Ø5/16" Lock Washer (5) Ø5/16" Flat Washer (6) M4 x 1-3/4”

+1 extra) (20+1 extra) (20+1 extra) (12+1 extra)

(8

T-handle Allen Wrench (1) Open-end Wrench (1) Touch-up Pen (1)

Tools required: Allen wrench and open-end wrench (provided) and Phillips screwdriver (not provided).

Wood Screw

Please call for replacement parts or assistance:

1-866-942-5362

Whalen Furniture Manufacturing Page 3 Factory No. 16650

Stock # PAR2PST

④

Assembly Instru ct i o ns

ready to assemble. To avoid causing damage to the thread, DO NOT over-tighten the nuts or bolts.

1. Unpack the unit and confirm that you have all the hardware and required parts.

2. Remove the plastic caps from the hanger bolts of the Front Legs (C and D) for the following steps.

3. Attach one Left Front Leg (C) to the Left front corner block of one Seat Frame (B) by inserting the

hanger bolts on the leg through the drilled holes on the corner block and fit the Flat Washer (5), Lock
Washer (4) and Hex Nut (3) onto each hanger bolt. Securely tighten the nuts with the provided open-end
wrench.

NOTE: DO NOT fully tighten all the nuts until the chair has been adjust and level all the legs so that they
do not wobble. Once adjusted, go back and tighten while making sure that the unit remains level.

4. Insert the tenon of one Front Stretcher (G) into the mortise of the Left Front Leg (C). Make sure that the

slant holes on the stretcher will face the floor when the unit is turned upright.

5. Repeat the same procedure to attach one Right Front Leg (D) to the right front corner block of the Seat

Frame (B). Be sure the mortise on Right Front Leg (D) fit onto the tenon of the Front Stretcher (G)
properly.

DO NOT fully tighten the bolts or nuts initially until all the bolts or nuts are

Ø5/16" Hex Nut

(4 used in this step)

③

Lock Washer

(4 used in this step)

Flat Washer

(4 used in this step)

⑤

Please call for replacement parts or assistance:

Whalen Furniture Manufacturing Page 4 Factory No. 16650

1-866-942-5362

Stock # PAR2PST

④

Assembly Instru ct i o ns

6. Lay one Backrest (A) on a smooth and protective surface with the threaded inserts facing up.

Ø5/16" x 3-1/4” Bolt

(4 used in this step)

②

Lock Washer

(6 used in this step)

7. Insert the tenon of Left and Right Side Stretchers (E and F) into the mortises of the Backrest (A). Make

sure the slant holes on the Side Stretchers will face the floor when the unit is turned upright.

8. Attach the assembled Seat Frame (B) to the middle rail of the Backrest (A) and insert both Side

Stretchers (E and F) into the Front Legs (C and D) respectively. Insert the 3-1/4” Bolts (2) with the
Washers (4 and 5) through the drilled holes on the Seat Frame (B) at rear corner blocks and loosely
tighten into the threaded inserts on the Backrest (A). As shown.

9. Secure the Seat Frame (B) to the Back rest (A) by inse rting two 1-1 /2” Bolts (1) wi th the Washers ( 4 and

5) into the drilled holes on the rear rail of the Seat Frame.

NOTE: DO NOT fully tighten the bolts.

Ø5/16" x 1-1/2” Bolt

(2 used in this step)

①

Flat Washer

(6 used in this step)

⑤

Please call for replacement parts or assistance:

1-866-942-5362

Whalen Furniture Manufacturing Page 5 Factory No. 16650

Stock # PAR2PST

⑥

Assembly Instru ct i o ns

10. Position the assembled unit upside down on the carton or other support surface, as shown.

NOTE: Place a protective cover (like the bubble wra p pa c king material) over the carton or other support
surface to prevent from scratching.

11. Insert and screw six 1-3/4” Wood Screws (6) into the slant holes in the Stretchers (E, F and G). Tighten

the screws with a Phillips screwdriver.

12. Stand the assembled unit upright on a flat surface. Press down the Seat Cushion (B) to even all legs. Now,

tightly fasten all bolts with the provided Allen wrench.

13. Repeat the same process to assemble the other chair.

Please call for replacement parts or assistance:

1-866-942-5362

Whalen Furniture Manufacturing Page 6 Factory No. 16650

M4 x 1-3/4” Wood Screw

(4 used in this step)

Stock # PAR2PST

Care and Maintenance

 Use a soft, clean cloth that will not scratch the surface when dusting.
 Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area.
 Using solvents of any kind on your furniture may damage the finish.
 Never use water to clean your furniture as it may cause damage to the finish.
 Always use coasters under beverage glasses and flowerpots.
 Liquid spills should be rem ove d immediately. Using a soft clean cloth, bl o t the spill gently. Avoid rubbing.
 Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create

spotting within the furniture finish.

 Stains or marks from crayons or ink markers will be difficult to remove.
 In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a

professional to repair your f urniture.

 Check bolts/nuts periodically and tighten them if necessary.

Further advice about wood furniture care

It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity
changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from
direct s unlight a s sun may damage the finish.

Proper care and cleaning at home will ext end the life of your purchase. Follo wing these important and h elpful
tips will enhance your furniture as it ages.

A Touch-up Pen has been provided to repair any small nicks or scratches that may occur during assembly or
shipping.

We hope you enjoy your purchase for many years.

Thank you for your purchase!

Please call for replacement parts or assistance:

1-866-942-5362

Whalen Furniture Manufacturing Page 7 Factory No. 16650

*PAR2PST-3-FS Front Stretcher *PAR2PST-10-5/16HN Ø5/16" Hex Nut

p

p

*PAR2PST-4-LSS Left Side Stretcher *PAR2PST-11-LW Ø5/16" Lock Washer

*PAR2PST-5-RSS Right Side Stretcher *PAR2PST-12-FW Ø5/16" Flat Washer

*PAR2PST-6-LFL Left Front Leg *PAR2PST-13-1 3/4WS M4 x 1-3/4" Wood Screw

*PAR2PST-7-RFL Right Front Leg *PAR2PST-14-OW Open Wrench

*PAR2PST-CH Complete Hardware *PAR2PST-15-THAW T-Handle Allen Wrench

*PAR2PST-1-B Backrest *PAR2PST-8-1-1/2B Ø5/16" x 1-1/2” Bolt

*PAR2PST-2-SFC Seat Frame with Cushion *PAR2PST-9-3-1/4B Ø5/16" x 3-1/4” Bolt

IF YOU NEED TO ORDER ANY REPLACEMENT PARTS, PLEASE USE THE LIST BELOW

Parker 2-pk Stools (PAR2PST)

*PAR2PST-16-TUP Touch-u

Pen