TM
REV 8 and REV 10
Owner’s Manual & “Limited” Warranty
Technology Specifications:
Thank You for purchasing this Wet Sounds product. Wet Sounds marine audio products
represent the ultimate in high performance standards. The Revolution Series is specifically
engineered to withstand the rigorous marine environment. Utilizing the state of the art
acoustic engineering and three dimensional computer aided design, our “Revolution
Technology” represents the most advanced technologies available for wakeboard tower
speaker systems. The Revolution series also provides multiple fitment options from direct
cast mount to fixed clamp mount to our revolutionary (Patent Pending) stainless steel TC3
Quick Disconnect Swivel clamp.
Please take a moment to read the instruction manual before starting your installation. This
manual will explain the benefits of the technologies developed by Wet Sounds and will help
you understand the correct installation methods and use of this product. If you have any
questions or concerns please contact a certified Wet Sounds dealer. You may also contact
Wet Sounds technical support by dialing 1-877-WET-SPKR (1-877-938-7757)
SPEAKER SPECIFICATIONS REV 8
RMS: 200 watts
Peak: 400 watts
Mid Bass: 8 inch Kevlar reinfo rc ed EFG™ cone woofers with polyurethane surround
High Frequency: Pro-Axial™ Driver - Coaxially mounted Titanium Diaphragm High Output
Horn Loaded Compression Driver
Impedance: 4 ohm
Frequency Response: 20Hz to 20 kHz
Sensitivity: 92DB at 1W/1M
SPEAKER SPECIFICATIONS REV 10
RMS: 300 watts
Peak: 600 watts
Mid Bass: 10 inch Kevlar reinforced EFG™ cone woofers with polyurethane surround
High Frequency: Pro-Axial™ Driver - Coaxially mounted Titanium Diaphragm High Output
Horn Loaded Compression Driver
Impedance: 4 ohm
Frequency Response: 20Hz to 20 kHz
Sensitivity: 92DB at 1W/1M
The Revolution™ series uses our proprietary REV TEC™ technology. Unlike most
conventional designs, REV TEC technology provides remarkable volume and amazing full
range sound quality on axis and off axis at long distances. Extensive acoustic testing has
confirmed these speakers ability to project volume at 80 feet and beyond without any loss of
detail or information. Not only does the Revolution series achieve volume and sound quality
at a minimum of 80 ft, but with the REV TEC technology the rider can enjoy quality sound
while riding outside the wake and being almost parallel to boat. Taking high performance
wakeboard tower speakers to the next level, Wet Sounds has consulted with experts who
spent countless hours examining the human auditory system to find out which frequencies
affect your ears the most at loud volumes. The Revolution series has been designed from the
ground up to provide stunning output while eliminating certain frequencies that give that
“ringing” or harsh sound associated with loud volumes. This allows the Revolution speakers
to provide maximum output while still providing world class sound quality without the
listener fatigue usually associated with high volumes.
The driver compliment in each REV 8 combines one 8 inch Kevlar reinforced EFG™ driver
and one concentrically mounted HLCD (Horn Loaded Compression Driver). The driver
compliment in each REV 10 also combines one 10 inch Kevlar rein for ced EFG™ driver and
one concentrically mounted HLCD (Horn Loaded Compression Driver) which provide stellar
performance and higher perfo rmance for the marine environment, Wet Sounds™ developed a
proprietary cone material called EFG™, which is an epoxy and fiberglass composite mix.
Adding a reinforcement of Kevlar, the mid bass cones become more rigid without any added
weight. This cone material incorporates characteristic values that are impermeable to
damage from intermittent Ultra Violet exposure and minimal moisture exposure. Like the
EFG™ cone material, the Polyurethane that is used for the surround will provide protection
against Ultra Violet exposure and moisture. This will prevent deterioration of the surround
yielding longer life and better reliability. We do, however, encourage you to either remove or
cover your tower speakers when they are not in use. Limiting exposure to Ultra Violet Rays
and to moisture will help extend the life of your tower speakers.
The high frequency transducer is our proprietary titanium Wet Sounds HLCD (horn loaded
compression driver). This driver was designed to provide a wide; horizontal trajectory that
would not only produce sound in the directed path but will disperse sound off axis with little
to no degradation. The HLCD is considered to be one of the most efficient transducer designs
providing remarkable output while using less power. Our unique (patent protected) design
incorporates the HLCD mounted to the rear of the mid bass driver. Our Pro-Axial™ design
allows the compression sound to travel through the voice coil former and out of the (patent
protected) horn flare that is mounted coaxially. This provides phenomenal volume and
accurate clarity.
***Caution: Do not spray any of the speakers directly with any liquid base substance.
Warranty will be voided if improper care is discovered during extensive examination of the
product.
Installation:
REV8 FC and REV 10 FC
TC3-F Fixed Clamp Pipe Version Installation (pipe tower)
Step 1: Attac h Male Conne ctor (7) from clamp base t o Female Connector (8)
Step 2: Push c onnector into center hole of speaker as you place clamp base
onto the speaker housing. Please make sure the grommet (9) is seated properly.
Step 3: Attac h two short A llen Bolts ( 4) through the clamp base and tighten
into the housing. Please make sure t hese are tig ht. It is also recommend t o use
a Blue Locti te on these b olts.
Step 4: Find the mounting loc a tio n for the spe a ker and clamp and then mark the
location on the bottom side of the pipe for the speaker wire. The speaker wire
will be inserted back into the pipe for a clean installation.
Step 5: Drill a small hole in the pipe and de burr the h ole so there is no sharp
edges. It is also recommend to install a rubber grommet in this hole to protect
the wire.
Step 6: Slide the wire ja cket (1) down the wire and Butt Connect the speaker
wire comin g from the towe r to the speaker wire plu g (5). Red is positive and
black is negati ve
Step 7: Attac h Clamp Top (3) to clamp base (6) usin g the two long A llen Bolts
(2)
Step 8: Make sure the clamp is tightened all the way so there is no movement
Installation:
REV8 SC and REV 10 SC
“Patent Pending” TC3-S Swivel Clamp Version Installation
Pipe Tower Mount Version using the TC3-S
Step 1: Attach Male Connector (10) from clamp base to Female Connec tor (11)
Step 2: Push c onnector into center hole of speaker as you place clamp base
onto the speaker housing. Inse rt 4 bare wires down into this hole a s well. These
wires are only used if you are adding the LED spea ker rings. (pl ease see LED
speaker ins tall instructions for LED install) Please ma ke sure the grommet (12)
is seated proper ly .
Step 3: Attac h two short A llen Bolts (16) through the clamp base and tighten
into the housing. Please make sure t hese are tig ht. It is also recommend t o use
a Blue Locti te on these b olts.
Step 4: Clamp Bottom (3) and Detachment Plate (5) are already connected
together. Insert the detachment plate into the clamp base (9). Please ma ke sure
the male speaker plug (7) and female speaker plu g (4) are lined up properly.
The male speaker plug (7) inside the clamp base can rota te. Please r otate this
so that it is facing the proper direction. There is a U shaped groove on the
female that lines up with a boss on the male.
Step 5: Slide the detachment fork (17) into the gr ooves on the c lamp base.
Attach the a llen locking bolt (19) and tighten dow n.
Step 6: Find the mounting location for the speaker and clamp a nd then ma rk the
location on the bottom side of the pipe for the speaker wire. The speaker wire
will be inserted back into the pipe for a clean installation.
Step 5: Drill a small hole in the pipe and de burr the h ole so there is no sharp
edges. It is also recommend to install a rubber grommet in this hole to protect
the wire.
Step 6: Slide the wire ja cket (13) down the wire and Butt Connect the speaker
wire comin g from the towe r to th e spea ke r w ire plug (4). Red is po sit iv e an d
black is negati ve. I f you have added the LED accessory, this speaker wire plug
(4) will have 6 conductors. Please refer to the LED install instructions.
Step 7: Attac h Clamp Top (2) to clamp bottom (3) using the two lo ng Allen
Bolts (1)
Step 8: Make sure the clamp is tightened all the way so there is no movement
Step 9: The swivel clamp allows you to rotate the speaker any direction you
may want. Loosen the allen lo ck i ng bolt ( 19) an d rotate the speaker to th e
direction you li ke. Then tighten the bolt to lock it in place.
Step 10: The swivel clamp also allow s you to rem ove the speake r from the
tower in seconds. Loose n the allen l ocking bolt (19) and remove the
detachment fork (17). Once removed, the speake r will disconnect from the
clamp. The clamp rema ins on the tower. To reinsta ll, line up the male speaker
plug (7) so that it is centered and inse rt the speaker by pluggi ng the connector
together an d reinstalling the detachment fork.
Cast Mount Tower Version using t he TC3-S clamp for quick disconnect
and swivel function.
Step 1: Attach Male Connector (10) from clamp base to Female Connec tor (11)
Step 2: Push c onnector into center hole of speaker as you place clamp base
onto the speaker housing. Insert 4 bar e wires down into this hole as well. These
wires are only used if you are adding the LED spea ker rings. (pl ease see LED
speaker ins tall instructions for LED install) Please ma ke sure the grommet (12)
is seated proper ly .
Step 3: Attac h two short A llen Bolts (16) through the clamp base and tighten
into the housing. Please make sure t hese are tig ht. It is also recommend t o use
a Blue Locti te on these b olts.
Step 4: Clamp Bottom (3) and Detachment Plate (5) are already connected
together. Remove allen bolts (6) that hold the detachment plate (5) to the clamp
bottom (3). Clamp Top (2) and Clamp Bottom (3) will not be used for a cast
tower mount.
Step 5: The d etachment plate (5) will be hard mounted to a ca st tower. Butt
connect spe aker wires from detachment plate con nector (4) t o the speaker wires
from the cas t tower. Red is positive and Black is negative.
Step 6: Push wires into c enter hole ba ck into the tower and attach the
detachm ent plate to t he tow er.
Step 7: Please make sure t he male speaker plug (7) and female speaker plug ( 4)
are lined up properly. The male speaker plug (7) inside the clamp base can
rotate. Please rotate this so that it i s facing the proper direc tion. There is a U
shaped groove on the female that lines up with a boss on the male.
Step 8: Insert speaker w ith base onto detachment plate. Slide on detachment
fork (17) and allen bolt (19) and tighten allen bolt so the speaker does not
move.
Step 9: The swivel clamp also allows you to remove the speaker from the tower
in seconds. Loosen the allen locking bolt ( 19) and rem ove the detac hment fork
(17). Once removed, the speaker will disconnect from the clam p. The
detachment plate rem ains on the tower. To rein stall, line up the male sp eaker
plug (7) so that it is cente re d and insert the spea ker by plugging the connector
together an d reinstalling the detachment fork.
X Mount Version. Cast to wer fixed mo unt version.
Step 1: Remove 4 screws holding the gr ille and drive r onto the housing. And
remove the grille and speaker from the housing. Disconnect speaker wire s from
mid bass and c ompressio n driver. Remove acoustic dampening material.
Step 2: Remove two sma ll Phillips screws from the top of the ho usi ng ne xt to
the grommet (2) This will loosen the internal threaded plate.
Step 3: From inside the housing. Slide out the internal threaded plate and
replace with non threa ded plate from X kit. Make sure to install it in the same
direction so the scre w hole s line u p.
Step 4: Take the two powde r coated top plates and attach on top of the speaker.
Use two longer Phillips screws provided i n the X kit to attach top plates into
internal non threaded plate.
Step 5: Butt c onnect Male Connector ( 1) to the fact ory wires. Red for positive
and black for negative.
Step 6: Take housing and hold up to the tower and plug the connectors together
(1) and (2) a nd push as much back into the tower and feed the remaining and
connector s into the center hole of the housing.
Step 7: Take the 2 bolts using the washers and lock washers and bolt the
housing up to the tower. Please make sure that the se bolts are tight. Some
towers and a dapters will only need a s ingle lock wa sher and single regular
washer. Other towers and adapters may need ext ra washers t hat have been
provided in the kit. If you find that the bolt bottoms out and t he housing is not
tight, please add washers to proper ly seat and t ighten the housing to the tower.
(The holes o n the plates should line up directly wi th the factory threaded i nsets.
However we have seen some towers that are not threa ded in the proper
locations. If this is th e case. Please contact W et Sounds at 877-938-7757 for
advice)
Step 8: Insert the acous tic dampening material.
Step 9: Hold the driver up to the housing to connect the speaker wires. Connect
the “soldered” white wire to the + positive (Red) push down ter minal on the
compressi on horn. Connect the “soldered” black wire to the – negative (Black)
push down term inal o n the c ompression horn.
Step 11: Connect the wire with the spade connector (Red) to the + positive of
the mid bass woofer. Con nect the wire with the spade connector (Black) to the
- negative of the mid bass woofer.
Step 12: Inse rt the driver into the hou sing. Insert the grille into the housi ng
making sure to line up all 4 mounting locations and attach the 4 stainless
screws around to the ho using. Please make sure these are tight but DO NOT
over tighten
“Limited Warranty”
What This Warranty Covers
This is a "Limited" warranty. This warranty covers any defects in materials and workmanship
and warranty only applies to the original purchaser and is not transferable. This warranty is
also only valid if the original purchase was made from an authorized Wet Sounds™ dealer.
How Long Coverage Last
This warranty runs for one year from the date of the purchase. It is recommended to
REGISTER your warranty online within 45 days of your purchase at www.wetsounds.com click on "warranty registration".
What Is Not Covered
This warranty does not cover fading or discoloration caused by exposure to sunlight or
chemicals such as ammonia, household bleach, or any cleaning material that contains
abrasive substances. (For information on how to prevent fading or discoloration, consult for
recommendations on cleaning products) Wet Sounds, Inc. does not cover the cost for
removal and reinstallation of any kind. Additionally, shipping TO Wet Sounds, Inc. is
covered by the purchaser This warranty is void and inapplicable if Wet Sounds™ deems that
the product was abused or misused; including but not limited to Speaker product that has
been improperly-powered (under or over powered), causing thermal (burnt voice coil) and/or
mechanical failure (torn surrounds or spiders), damage caused by accident, mishandling,
improper installation, negligence, normal wear and tear, excessive water or heat damage,
freight damage or products that have been altered in any way. Product owned by anyone
other than the original purchaser from an authorized Wet Sounds dealer. (The warranty is not
transferable and will not apply to products purchased from unauthorized dealers.) Wet
Sounds is not responsible for any damages to a consumer's boat or person from a product
failure. The warranty is void if Wet Sounds deems the product was installed or used
improperly. Wet Sounds shall not be responsible for any incidental or consequential
damages, except to the< extent provided (or prohibited) by applicable law. This warranty
gives you specific legal rights, and you may also have other rights which vary from state.
What Wet Sounds™, Inc. Will Do
Wet Sounds, Inc will repair any part of your product that proves to be defective in materials
or workmanship. In the event repair is not possible, Wet Sounds, Inc will replace the product
in question. If it is deemed necessary Wet Sounds, Inc. will either replace the entire product
with a refurbished unit or it will be replaced with a model that is similar in price if that model
is no longer available. Labor cost and materials needed to complete this service will be at no
charge to the purchaser. Additionally, the cost of shipping TO the consumer is also covered
under this warranty.
How to Obtain Warranty Service
Contact Wet Sounds, Inc. either by phone at 877-938-7757 or by email at
warranty@wetsounds.com. A service representative will assist you in the necessary actions
to verify that the problem that you are experiencing is covered under warranty. If it is in fact
a warranty issue, Wet Sounds will issue an RA number for tracking purposes and give
instructions on sending the product in for evaluation. Wet Sounds™, Inc. How State Law
Applies This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
Internet Warning
Wet Sounds, Inc. products sold on any non authorized web site or internet auction site are
void of any and all manufacturer's warranty. Please contact Wet Sounds™ at 877-938-7757
or visit our web site at www.wetsounds.com to search for an authorized site and/or an
authorized retailer near you.
Caution & Respect
Wet Sounds™ speakers can achieve very high sound pressure levels. Please use this product
responsibly. Be aware that sound travels great distances across water so please respect other
boaters especially while loading/unloading at the ramp or dock. Wet Sounds, Inc. is not
responsible for any violations of the law that may be a direct result of excessive volume.
Please abide by the rules but have fun doing it.
Wet Sounds, Inc.
9330 West Airport Blvd. suite 170
Houston, Texas 77031
www.wetsounds.com
Toll Free: 8 77-938-7757
Loading...