West Penn AV-IP-AMPRX, AV-IP-AMPTX Specsheet

Audio AMP IP

Specifications

Environment

2CH analog audio distribution over multiple zones via an IP network.

Devices

2CH audio source equipment, microphone systems, speakers, PA systems.

Signal Bandwidth

20Hz to 20KHz

LCD Display

2 line x 20 character backlit LCD display (on TX)

Control

Local control via front push/turn knob and LCD display, remote control via web interface and AV-IP-NC811 controller (on TX).

Audio Signals

Two (2) 2CH analog audio in
One (1) Mic in
One (1) SPDIF Out (2CH digital audio)

Connectors

Note: Cables not included.

Two (2) RCA receptacle for Analog Audio In (on TX)
One (1) 3.5mm jack for Analog Audio In (on TX)
One (1) 3-pin phoenix connector for Mic In (on TX)
One (1) RCA receptacle for SPDIF Out (on RX)
Two (2) RJ45S for Cat 5e/6 unshielded or shielded twisted pair (one for TX and one for RX)
Two (2) 3.5mm jack for IR Emitter or IR Sensor (one for TX and one for RX)
Two (2) DB9 Serial Ports for RS232 (one for TX and one for RX)
Two (2) 8-position DIP Switches for device ID addressing and config (one for TX and one for RX)
One (1) 4 pin phoenix connector speaker terminals (2x50W into 8Ω)
Two (2) 2.1mm locking power connector (one for TX and one for RX)

Cable

One (1) Cat 5e/6 or better twisted pair cables required.

Maximum Distance

Cat5e/6: 330ft (100m)

Note: When installed in an electrically noisy environment, an STP cable must be used. Also, cross-connections in the signal path reduce the
effective distance depending on the grade of twisted cable used.

IR Frequency

Directional IR: 38KHz to 56KHz

RJ45 Pin Configuration

Reverse Polarity Sensitive. Use
EIA/TIA 568A or 586B straight­through wiring.

RJ45 Link

Pin 1 (R) Pin 2 (T)
Pin 3 (R) Pin 6 (T)
Pin 4 (R) Pin 5 (T)
Pin 7 (R) Pin 8 (T)

Power Source

Transmitter: Supports PoE (PD), an external power supply is not included. It is intended to be powered via a PoE (PSE) Ethernet Switch. If
required, an optional power supply may be purchased separately (see West Penn Wire website product page for more details).
Receiver: Includes a power supply (160W maximum, 32VDC 5A).

PoE Standard

IEEE 802.3af

Power Consumption

Transmitter: 3W Receiver: 160W (max)

Temperature

Operating: 0° to 40°C Storage: -20° to 85°C
Humidity: Up to 90% non-condensing

Dimensions

TX: 4.33” x 4.76” x 1.97” (11 x 12.1 x 5 cm), RX: 4.33” x 7.91” x 1.97” (11 x 20.1 x 5 cm)

Weight

TX: 1.20lbs (0.55kg), RX: 1.96lbs (0.89kg)

Compliance

Regulatory: FCC, CE, RoHS Flammability: 94V0

Warranty

3 years

Order Information

AV-IP-AMPRX AUDIO AMP IP Receiver (UPC: 612825417712)
AV-IP-AMPTX AUDIO AMP IP Transmitter (UPC: 612825417699)

Accessories

(Items sold separately)

Univ. Locking Power Supply 5VDC/2.6A
IR Sensor and IR Emitter
(See West Penn Wire website product page for more details)

AV-IP-AMP

Overview:

The Audio AMP IP Transmitter and Receiver allows one of
two 2CH Analog Audio-in and Mic-in signals to be extended
over an IP network, and up to 330ft (100m) from an
Ethernet Switch via Cat5e/6 cable in a point-to-point
configuration. Point-to-multipoint and multipoint-to-multipoint
is supported by connecting several Transmitters and
Receivers to the same local Ethernet network. Depending
on the application one or more Transmitters (AV-IP-AMPTX)
can communicate with (or multicast to multiple Receivers
(AV-IP-AMPRX).The Transmitter supports PoE (PD) if used
with a PoE (PSE) Ethernet Switch. Supports bidirectional
RS232 and directional IR transmission initiated via an IP
network or via pass-through for remote control of end
devices.

Applications:

 Commercial and residential AV systems
 K6 and K12 classroom AV systems
 Digital signage
 Boardroom systems
 Collaborative PC systems
 Medical information systems

Key Features:

 Supports dual 2CH Audio inputs and a Mic input (TX)
 Extend 2CH Audio or Mic signals up to 330ft (100m) over

Cat5e/6 cable

 Supports a 2x50W Amplifier, and bridge-mode for

1x100W (RX)

 Supports Digital Audio Out (RX)
 Control input selection, volume, bass and treble (TX)
 Manage TX unit locally via push/turn dial or remotely via

AV-IP-NC811 web interface

 Supports point-to-point, point-to-multipoint and multipoint-

to-multipoint applications

 Supports 100’s of Transceivers depending on network

bandwidth

 Supports RS232 and IR transmission for remote control of

end devices

 Transmitter may be PoE powered

© West Penn Wire 2018 AV-IP-AMP

Audio AMP IP

West Penn Wire | 2833 West Chestnut Street, Washington, PA, USA 15301

Tel: [phone] | E-mail: [e-mail] | www.westpennwire.com

AV-IP-AMP

_____________________________________________________________________________________

Typical Application

© West Penn Wire 2018 AV-IP-AMP