Page 1
INSTALLATION MANUAL
KIT CONTENTS
DESCRIPTION QTY
Cover top cabinet wh GR
Cover top cabinet wh WHT
Hinge top cover left GR
Hinge top cover left WHT
Hinge top left 1
Hinge centre left 1
Hinge bottom base left 1
Door auto closer LH 2
NOTE: Keep kit parts separate from other parts as you
disassemble them to avoid mix-ups.
1
1
1
1
TOOLS YOU WILL NEED (not supplied)
Models: WTB2300WC, WTB2300PC, WTB2500WC, WTB2500PC, WTB2800WC,
INSTRUCTIONS
1. Ensure refrigerator is empty of all loose items and
unplugged from power source.
2. Store power cord next to motor to prevent damage.
Check for water in drain pan and remove any water
with a cloth or sponge if necessary.
drain pan
motor
Rear view of
refrigerator
REFRIGERATOR DOOR REVERSAL KIT
WTB2800PC, WTB3400WC, WTB3400PC, WTB3700WC, WTB3700PC
7. Remove freezer door by opening 45º and gently slide
off hinge. Set door aside to prevent damage.
45º
8. Unscrew 2 centre hinge screws. Remove the Covers
and 2 Phillips screws underneath the covers. Do not
discard screws and covers.
screws
and covers
screws
Phillips head screwdriver
"
16
8mm (5/
) hex head socket
WARNING
Westinghouse takes no responsibility for incorrectly assembled
doors leading to injury or malfunction.
CAUTION
Refrigerator must stand for 30 minutes prior to connecting to
power supply to ensure system functions correctly.
IMPORTANT
All hinge screws require tightening to a torque setting
of 5-10Nm.
FRIDGE DESCRIPTION
Top view of right hand hinge cabinet
1
4
3
Bottom view of right hand hinge cabinet
3. Lay the refrigerator on its back.
WARNING
Your refrigerator is heavy–you may need assistance.
4. Remove the hinge cover with a soft plastic lever.
2
5. Remove the LH cap with a soft plastic lever.
9. Remove RH centre hinge by lifting the door slightly and
sliding hinge out of the door.
1
2
10. Remove food door by opening 45º and gently slide
off hinge. Set door aside to prevent damage.
45º
11. Remove the Pocket Handle Cover and Cover door
from the Fzr door and assemble them on the other
side. Remove the RH Door auto closer and replace
with LH Door auto closer (kit Content) on the other
side. Repeat the same steps with Food door.
cover door
5
1 Cover top cabinet WH
2 Hinge top right and hinge top
cover right
3 Cover screw mullion WH
and screws
4 Hinge centre right
and screws
5 Adjustable foot
6 Hinge bottom assy right
6
6. Unscrew 3 x 8mm top hinge screws and remove RH top
hinge. Do not discard screws.
door auto
closer LH
pocket
handle
cover
door auto
closer RH
Page 2
Follow Step number 12 to 16 for model WTB2300 and
WTB2500 where fitted with Kick Plate). For other models
without Kick Plate please skip to Step number 17 and
onwards.
12.
Unscrew the four screws indicated below to remove the
side kickplates.
13. Unscrew the bottom hinge screw shown, pull the hinge
away from cabinet then up to remove.
19. Place the bottom hinge LH (kit contents) onto the
cabinet, placing it down then towards cabinet to
install. Replace the screw.
1
2
20. Replace the hinge foot onto the LH bottom hinge and
tighten with screw.
26. Ensure that the edges of the doors are parallel with the
sides of the cabinet.
27. Ensure that the food door and the freezer door have a
parallel gap.
1
2
14. Place the bottom hinge LH (Kit content) onto the
cabinet, placing it down then towards cabinet to
install. Replace the screw.
1
2
15. Remove the spacer from the kickplate and clip to the
other side.
16. Assemble the kickplate to the refrigerator using the
four screws.
21. Replace the food door by holding at 45º and gently
slide onto the bottom hinge and closing the door.
45º
22. Replace LH centre hinge (Kit Content) by lifting the
door slightly and sliding hinge into the door and
placing the door down again.
1
2
23. Insert 2x8mm screws from existing center hinge into
the LH center hinge, tighten the screws until the bracket
is secured. Assemble the 2 Phillips head screws and
covers on other side as shown.
28. Fully tighten the LH top hinge to the cabinet until the
hinge is secure.
29. Clip the LH hinge cover (kit contents) over LH
top hinge.
30. Insert the RH top hinge hole cap (kit contents) in the
cabinet as shown.
screws
& covers
Skip Steps 17 to 20 and follow from Step 21 & onwards.
17. Unscrew the hinge foot using phillips head screwdriver
and unscrew foot on opposite side. Do not discard.
18. Unscrew the bottom hinge screw shown, pull the hinge
away from cabinet then up to remove.
1
2
For further information on all Westinghouse appliances, or to obtain detailed dimension and installation information,
call into your Retailer, phone or email our Customer Care team or visit our website:
AUSTRALIA
phone: 1300 363 640
fax: 1800 350 067
email: customercare@electrolux.com.au
web: www.westinghouse.com.au
NEW ZEALAND
phone: 09 573 2384
fax: 0800 363 600
email: customercare@electrolux.co.nz
web: www.westinghouse.co.nz
24. Replace the freezer door by holding at 45º and gently
slide onto the centre hinge and closing the door.
45º
25. Slide the LH top hinge (kit contents) into the door,
loosely screw the 3 x 8mm screws from the existing top
hinge in the cabinet.
screws
31. Stand the refrigerator upright.
WARNING
Your refrigerator is heavy–you may need assistance.
33. Level the cabinet by adjusting the foot.
** Recommended to apply a small amount of silicone grease
(Molykote EM-50L or equivalent -- not provided with kit) on
all pivoting pin of left hand hinges for lubrication **
© 2013 Electrolux Home Products Pty Ltd ABN 51 004 762 341
Westinghouse. We are part of the Electrolux family.
Share more of our thinking at www.electrolux.com
WMAN_DOORREV_June13
Part number: 807557701
Loading...