GAS COOKTOPS
User and Installation Manual
MODELS
GHS607S/W, GHC6 07S/ W, G H C617S/ W,
GHS917S/W, GHC937S/ W, 72K315S/W, GH R12S/W,
GHR92S, WHG640SA/WA, CHG642SA/WA,
CHG646SA/WA, CHG956SA/WA, CHG606SA,
SHG646SA, SHG956SA, WHG641SA, WHG643SA,
WHG645SA/WA, WHG951SA, WHG955SA/WA
WARNING
WARNING
TIPS & INFORMATION
ENVIRONMENTAL TIPS
TIPS & INFORMATION
ENVIRONMENTAL TIPS
general safety
CONGRATULATIONS
Congratulations and thank you for choosing our Gas
Cooktop. We are sure you will find your new appliance a
pleasure to use and a great asset to your cooking. Before
you use the appliance, we recommend that you read through
the whole user manual which provides
a description of the product and its functions.
To avoid the risks that are always present when you use a
cooking appliance, it is important that the appliance is installed
correctly and that you read the safety instructions carefully to
avoid misuse and hazards. For future reference, please store
this booklet in a safe place. This appliance complies to the
requirements of Australian Standard AS4551.
CONDITIONS OF USE
This appliance is intended to be used in household and
similar applications such as:
• Staff kitchen areas in shops, offices and other
working environments
• Farm houses
• By clients in hotels, motels and other residential
type environments
• Bed and breakfast type environments
Record model and serial number here:
Model: ..................................................................
Serial number: ........................................................
The symbols you will see in this booklet have these meanings:
warning
Indicates information concerning your personal safety
caution
Indicates information on how to avoid damaging the appliance
tips & information
Indicates tips and information about use of the appliance
environmental tips
Indicates tips and information about economical and
ecological use of the appliance
tips & information
Important – check for any damage or marks
If you find the appliance is damaged or marked, you must
report it within 7 days if you wish to claim for damage/
marks under the manufacturer’s warranty. This does not
affect your statutory rights.
CONTENTS
General safety .......................................................3
Using your cooktop ..............................................4
Cleaning and care .................................................5
Troubleshooting .....................................................6
Technical data ........................................................7
Installation .......................................................... 11
LPG conversion - Dong Yang Regulator .......................13
LPG conversion - Chant Regulator ..............................15
Electrical connection ................................................16
Testing appliance operation ...................................... 17
Warranty ..............................................................19
Read the following carefully to avoid an electric
shock or fire
General warnings
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
• Young children should be supervised to ensure they
do not play with this appliance.
• During use this appliance becomes hot. Care should be
taken to avoid touching hot external and internal surfaces
when in use. Use oven gloves. Children should be kept
away to avoid burns and scalds.
• This appliance must NOT be used as a space heater.
• Keep vents clear of obstructions.
• In order to avoid a fire, the appliance must be kept clean.
• Do not spray aerosols in the vicinity of the appliance
when it is in operation.
• Do not store flammable materials in or under the
appliance, eg. aerosols.
• Do not modify this appliance.
Cooktops (generally)
• Do not allow pots to boil dry, as damage to both pan
and cooktop may result.
• Do not operate the cooktop for an extended period of
time without a pot or pan on the hotplate.
• Do not allow large cookware to overhang the cooktop
onto the adjacent benchtop. This will cause scorching to
the benchtop surface.
• Do not allow cooking pots or pans to intrude into the area
which is close to the controls.
• Ensure burner caps and trivets are properly located.
(see Figure1)
• For maximum stability, ensure pots and pans are centrally
located on the trivets.
• Handles should be turned away from the front of the
bench to avoid accidents.
• Only models fitted with flame safeguard can be used in
marine craft, caravans or mobile homes.
Figure 1
burner cap
NOTE: You must read these warnings carefully before
installing or using the cooktop. If you need assistance,
contact your Customer Care Department. The manufacturer
will not accept liability should the instructions below, or any
other safety instructions incorporated in this book, be ignored.
Installation
• An authorised person must install this appliance and
MUST provide a certificate of compliance.
• Before using the appliance, ensure that all packing
materials are removed from the appliance.
• In order to avoid any potential hazard, the installation
instructions in this booklet and any label on the appliance,
must be followed.
• Ensure that all specified vents, openings and air spaces
are not blocked.
• Where the appliance is built into a benchtop, the
benchtop material must be capable of withstanding
temperatures of 85°C.
• DO NOT install in marine craft, caravans or mobile
homes because these products are not fitted with a flame
safeguard on each burner.
Servicing
• Servicing MUST only be carried out by authorised personnel.
• To maintain safe operation, it is recommended that the
product be inspected every five years by an authorised
service person.
• For appliances supplied with a supply cord, if the supply
cord is damaged it must be replaced by an authorised
service person in order to avoid a hazard.
• For models with battery ignition, the battery will require
periodic replacement (see page 12).
NOTE: The battery is a perishable item and is not covered
by the warranty.
Cleaning
• Always ensure the appliance is turned off before cleaning.
• This appliance contains aluminium fittings. DO NOT use
caustic based cleaners.
• Do not use steam cleaners as this may cause moisture buildup on electrical components.
• Always clean the appliance immediately after any
food spillage.
• DO NOT place burner caps, crowns or griddle plate in a
dishwasher.
environmental tips
Information on disposal for users
• Most of the packing materials are recyclable. Please dispose
of those materials by contacting your local authorities and
ask for the correct method of disposal.
2 CONTENTS Gas Cooktops Gas Cooktops GENERAL SAFETY 3
burner crown
ignition electrode
injector
using your cooktop cleaning and care
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
warning
DO NOT spray aerosols in the vicinity of this appliance while it is
in operation as aerosols can contain flammable propellants.
warning
Where the appliance is installed in any confined area, the
area must be properly ventilated. It MUST NOT be used as a
space heater.
Controls
Each burner is controlled by a control knob. The markings
on the control panel indicate which burner the knob controls,
and the settings for that burner (see Figure 2).
Figure 2
OFF
HI
LOW
Lighting burners
Electronic ignition: These cooktops are fitted with mains
powered or battery ignition. When the appliance has been
connected and the power is on, depressing any knob will release
sparks to all burners (except push button ignition, see push button
ignition models). To light a burner, depress the corresponding
knob and turn to the ‘HIGH’ position (while depressing the knob).
The knob may be released once the flame is established.
Flame safeguard models
The knob must be turned to the ‘High’ position, then pushed
down as far as possible for approximately 5 seconds. If the
flame goes out when the knob is released, simply depress the
knob again, this time holding it down with slightly more force for
the same length of time. The height of the flame can be varied
by turning the control knob toward the “Low” position.
Push button ignition: Turn the knob to the ‘HIGH’ position and
press the ignition button down until the flame is established. The
height of the flame can be varied by turning the knob towards
the ‘LOW’ position.
warning
Keep hands clear of the burners when lighting.
If the burner does not light within 5 seconds, turn knob to ‘OFF’
position, allow gas to disperse then try lighting again.
caution
Burners MUST be operated between ‘HIGH’ and ‘LOW’
settings only.In the absence of electrical power, carry out the
ignition directly to the burner with a hand held ignition source.
Hotplates
Choice of hotplate
For your convenience there is a choice of hotplates:
• A small burner for special low heat and slow cooking.
• A medium burner for normal cooking and simmering.
• A large burner for fast heating and large pots and pans.
• A wok burner for very fast heating using a wok or large
pot or pan.
To conserve gas place the pan centrally over the burner and
adjust the flame so that it does not extend past the edge of the
pan (Figure 3). Do not boil food too rapidly.
A vigorous boil will not cook food any faster, and will
waste energy.
Pots and pans
All common pots and pans; aluminium, stainless steel, cast iron,
ceramic, etc., may be used on your new gas cooktop. Ensure
that the pots or pans are steady and have flat bases to avoid
dangerous spill-over of hot liquids and wasted energy.
Figure 3
Choice of flame height
7
Incorrect – flame too high and
will cause gas waste and possible
handle damage.
Choice of cooking utensils
3
For a large burner,
use a large utensil.
caution
Never use asbestos mats, wire mats or grids, or aluminium foil
as it can lead to overheating, cracked enamel or broken glass.
The warranty will be void if these items are used and cause a
failure. Woks should only be used on the wok burner and wok
support trivet.
3
Correct flame height.
Gas saved.
3
For a small burner,
use a small utensil.
warning
Ensure the appliance is off and cool before cleaning.
Enamel
Persistent stains may require rubbing with a nylon scourer or
creamed powder cleansers. Household enamel cleaners are
available, follow the manufacturer’s instructions in their use. Harsh
abrasive cleaners, powder cleaners, steel wool or wax polishes
should not be used.
Stainless steel
NOTE: Ensure any oil is cleaned off the hob before use,
otherwise it may cause the hob to turn a yellowish colour.
All grades of stainless steel may stain, discolour or attain an
adhering layer of grime in normal operation. To achieve
maximum surface appearance, stainless steel must be kept clean
by regularly using the following cleaning procedures. Wash
with warm soapy water and rinse with clean water. Where the
stainless steel has become extremely dirty with signs of surface
discolouration, (due to periods of neglect of misuse) use a stainless
steel cleaner. When removing these stains, be sure to follow the
polish or brushing lines.
caution
DO NOT use abrasive scourers or steel wool.
Trivets, burner caps and crowns
These can all be lifted off and removed for separate cleaning.
NOTE: When re-fitting the burner caps and crowns, ensure
that they are correctly seated.
Ensure burners are thoroughly dried after cleaning or spillage.
When cleaning the burners, ensure that all the flame ports are
free of any blockage (refer to Figure 1b on page 4). If necessary,
use a toothpick or brush to clear ports. The outer surface of the
burner caps have a polished finish and extra care needs to be
taken to avoid scratching this surface during cleaning. In instances
of heavy soiling, it may be necessary to apply a non-abrasive
cleaning compound and rub with a cloth until the soiling is
removed and then finish with a soft, dry cloth.
caution
DO NOT place trivets or burners in the dishwasher.
Ignition electrode
GENTLY clean the ignition spark plug and flame safeguard sensor
with a damp cloth to avoid lighting difficulties. Ensure that they are
dry before use.
Injector
Ensure the injector remains free of any foreign material.
If necessary, use a thin piece of wire to clear the orifice.
4 USING YOUR COOKTOP Gas Cooktops Gas Cooktops CLEANING AND CARE 5
troubleshooting
technical data
If you have a problem with the cooktop, check the table below. You may be able to solve the problem and this will
save you from paying for a service call. You will have to pay for a service call even in the warranty period if the
problem is one listed below.
Table 1
problem possible cause solution
Gas supply valve turned off Turn on gas supply to appliance
Control knob not on Turn knob on (refer to page 3)
Ensure the knob you are turning corresponds
to the burner you want to light
Repeat lighting procedure and hold knob
down for 5 seconds in ‘High’ position (refer
page 4)
Burner will not light even
Wrong knob turned
Knob not held down long enough in ‘High’
position for flame safeguard (where fitted) to
engage
though the sparker is
working
Port blockage in ignition area
Ensure that ports in ignition area are clean
and dry
Ignition electrode wet or dirty Dry or clean ignition electrode
Sparking at wrong point because of
incorrectly fitted burner crown
Ensure that the crown is seated properly so
that the spark fires to the receiving point in
the burner crown (refer to Figure 1)
Injector is blocked Ensure injector is clear of foreign material
Electricity supply is disconnected or switched
off
Switch on electricity or check fuses
FEATURES GHS607S/W GHC607S/W GHC617S/W GHS917S/W GHC937S/W
Brand Chef Chef Chef Chef Chef
Cooking zones 4 4 4 4 5
Wok No No Yes Ye s Yes
Ignition 1.5V battery 220-240V 220-240V 1.5V battery 220-240V
Trivet Wire Gloss Wire Gloss Wire Gloss Wire Gloss Wire Gloss
Hob material
Features Push button ignition Ignition through knob Ignition through knob Push button ignition Ignition through knob
Flame safeguard No No No No No
Gas Types
Cooktop dimension
Width (mm) 600 600 600 860 860
Depth (mm) 535 535 535 510 510
Height (mm) 58 58 58 58 58
Cutout dimension
Stainless Steel/
Enamelled White
NG, (LP conversion
kit supplied)
Stainless Steel/
Enamelled White
NG, (LP conversion
kit supplied)
Stainless Steel/
Enamelled White
NG, (LP conversion
kit supplied)
Stainless Steel/
Enamelled White
NG, (LP conversion
kit supplied)
Stainless Steel/
Enamelled White
NG, (LP conversion
kit supplied)
No spark is obtained
Battery is flat Replace battery (refer to page 12)
when control knob is
activated
Polarity wrong on battery
Reorient battery to correct position (refer to
page 12)
Ignition electrode wet or dirty Dry or clean ignition electrode
Flames uneven or tending
to lift
Flame ports blocked or wet Clean or dry flame ports
Burner cap/crown incorrectly fitted Ensure these components are fitted correctly
Knob not set between ‘HIGH’ and ‘LOW’ Knob MUST be set between these positions
Flames not staying on
when knob is released
Knob not held down long enough in ‘High’
position for flame safeguard (where fitted) to
engage
Repeat lighting procedure and hold knob
down for 5 seconds in ‘High’ position (refer
page 4)
Low heat, slow cooking Incorrect cooking pot or pan being used Refer to Figure 3 (page 4)
Incorrect cooking pot or pan used Refer to Figure 3 (page 4)
Benchtop or knobs
overheating
Cooktop stainless steel
discoloured
Pot or pan not located on burner properly
Pot or pan being used is too large
Ensure pot or pan is centrally ocated on
burner
Ensure pot sizes used are as per user manual
requirements. Clean with STEEL POWER
(available through spare parts)
Width (mm) 570 570 570 830 830
Depth (mm) 490 490 490 470 470
Energy rating (NG)
Small burner 5.1 MJ/h 5.1 MJ/h 5.1 MJ/h 5.1 MJ/h 5.1 MJ/h
Medium burner 2 x 9.0 MJ/h 2 x 9.0 MJ/h 2 x 9.0 MJ/h 9.0 MJ/h 2 x 9.0 MJ/h
Large burner 12.1 MJ/h 12.1 MJ/h 12.1 MJ/h 12.1 MJ/h
Wok burner 14.4 MJ/h 14.4 MJ/h 14.4 MJ/h
Total MJ/h 35.2 MJ/h 35.2 MJ/h 37.5 MJ/h 40.6 MJ/h 49.6 MJ/h
If all the above points have been checked and there is still a problem with the cooktop please call the Service Centre.
6 TROUBLESHOOTING Gas Cooktops Gas Cooktops TECHNICAL DATA 7
technical data
technical data
FEATURES CHG642SA/WA CHG646SA/WA CHG956SA/WA CHG606SA 72K315S/W
Brand Chef Chef Chef
Cooking zones 4 4 5
Wok Yes Yes Yes
Ignition 1.5V battery 220-240V 220-240V
Trivet Wire Gloss Wire Matt Wire Matt
Hob material
Features Ignition through knob Ignition through knob Ignition through knob
Flame safeguard No No No
Gas Types
Cooktop dimension
Width (mm) 600 600 860
Depth (mm) 535 535 510
Stainless Steel/
Enamelled White
NG, (LP conversion
kit supplied)
Stainless Steel/
Enamelled White
NG, (LP conversion
kit supplied)
Stainless Steel/
Enamelled White
NG, (LP conversion
kit supplied)
Chef
4
Yes
220-240V
Wire Matt
Stainless Steel
Ignition through knob
No
NG, (LP conversion kit
supplied)
600
535
Simpson
4
Yes
220-240V
Wire Gloss
Stainless Steel/
Enamelled White
Ignition through knob
No
NG, (LP conversion
kit supplied)
600
535
FEATURES SHG646SA SHG956SA GHR12S/W GHR92S WHG640SA/WA
Brand Simpson Simpson Westinghouse Westinghouse Westinghouse
Cooking zones 4 5 4 5 4
Wok Yes Yes No Yes No
Ignition 220-240V 220-240V 220-240V 220-240V 220-240V
Trivet Wire Matt Wire Matt Wire Matt Wire Matt Wire Matt
Hob material Stainless Steel Stainless Steel
Features Ignition through knob Ignition through knob Ignition through knob Ignition through knob Ignition through knob
Flame safeguard No No No No No
Gas Types
Cooktop dimension
Width (mm) 600 860 600 860 600
Depth (mm) 535 510 535 510 535
NG, (LP conversion
kit supplied)
NG, (LP conversion
kit supplied)
Stainless Steel/
Enamelled White
NG, (LP conversion
kit supplied)
Stainless Steel
NG, (LP conversion
kit supplied)
Stainless Steel/
Enamelled White
NG, (LP conversion
kit supplied)
Height (mm) 58 58 58
Cutout dimension
Width (mm) 570 570 830
Depth (mm) 490 490 470
Energy rating (NG)
Small burner 5.1 MJ/h 5.1 MJ/h 5.1 MJ/h
Medium burner 2 x 9.0 MJ/h 2 x 9.0 MJ/h 2 x 9.0 MJ/h
Large burner 12.1 MJ/h
Wok burner 14.4 MJ/h 14.4 MJ/h 14.4 MJ/h
Total MJ/h 37.5 MJ/h 37.5 MJ/h 49.6 MJ/h
58
570
490
5.1 MJ/h 5.1 MJ/h
9.0 MJ/h 2 x 9.0 MJ/h
12.1 MJ/h
14.4 MJ/h 14.4 MJ/h
40.6 MJ/h 37.5 MJ/h
58
570
490
Height (mm) 58 58 58 58 58
Cutout dimension
Width (mm) 570 830 570 830 570
Depth (mm) 490 470 490 470 490
Energy rating (NG)
Small burner 5.1 MJ/h 5.1 MJ/h 5.1 MJ/h 5.1 MJ/h 5.1 MJ/h
Medium burner 2 x 9.0 MJ/h 2 x 9.0 MJ/h 2 x 9.0 MJ/h 2 x 9.0 MJ/h 2 x 9.0 MJ/h
Large burner 12.1 MJ/h 12.1 MJ/h 12.1 MJ/h 12.1 MJ/h
Wok burner 14.4 MJ/h 14.4 MJ/h 14.4 MJ/h
Total MJ/h 37.5 MJ/h 49.6 MJ/h 35.2 MJ/h 49.6 MJ/h 35.2 MJ/h
8 TECHNICAL DATA Gas Cooktops Gas Cooktops TECHNICAL DATA 9
technical data
WARNING
installation
FEATURES WHG641SA WHG643SA WHG645SA/WA WHG951SA WHG955SA/WA
Brand Westinghouse Westinghouse Westinghouse Westinghouse Westinghouse
Cooking zones 4 4 4 5 5
Wok Yes Yes Yes Yes Ye s
Ignition 220-240V 220-240V 220-240V 220-240V 220-240V
Trivet Wire Matt Wire Matt Cast Iron Wire Matt Cast Iron
Hob material Stainless Steel Stainless Steel
Features Ignition through knob Ignition through knob Ignition through knob Ignition through knob Ignition through knob
Flame safeguard No Yes Yes No Ye s
Gas Types
Cooktop dimension
Width (mm) 600 600 600 860 860
Depth (mm) 535 535 535 510 510
Height (mm) 58 58 58 58 58
Cutout dimension
Width (mm) 570 570 570 830 830
Depth (mm) 490 490 490 470 470
Energy rating (NG)
Small burner 5.1 MJ/h 5.1 MJ/h 5.1 MJ/h 5.1 MJ/h 5.1 MJ/h
NG, (LP conversion
kit supplied)
NG, (LP conversion
kit supplied)
Stainless Steel/
Enamelled White
NG, (LP conversion
kit supplied)
Stainless Steel
NG, (LP conversion
kit supplied)
Stainless Steel/
Enamelled White
NG, (LP conversion
kit supplied)
Table 2
Cooktop dimensions Square Rectangular
width (mm) 600 860
depth (mm) 535 510
height (mm) 58 58
Cut-out dimensions
width (mm) 570 830
depth (mm) 490 470
caution
Cooktops are supplied for use with natural gas (NG). To use with
LPG, the injectors MUST be changed using the conversion kit
supplied. Refer LP Conversion on page 13 and 15).
This appliance must be installed by an authorised person and in
compliance with:
1. AS/NZS 5601.1 Gas Installations Part 1: General
Installations, and AS/NZS 5601.2 Gas Installations Part 2:
LP Gas installations in caravans and boats for non-propulsive
purposes, or the relevant installation code for gas appliances
in your country.
2. The local gas fitting regulations, municipal building codes,
electrical wiring regulations and any other relevant statutory
regulations.
3. The particular instructions as given below. Before commencing
installation, check to ensure that the appliance gas type given
on the data plate on the appliance corresponds with the type
of gas to which it is intended the appliance be connected.
4. A certificate of compliance MUST be given to the customer
after the application is successfully installed.
5. This appliance must be earthed (240V models only).
3. Optional barrier: A barrier can be installed to prevent
accidental contact with the cooktop base, where the base of
the cooktop is accessible from below (i.e. Inside a cupboard,
etc.). An impression has been incorporated into the base to
ensure a minimum clearance of 10mm is maintained between
the base and the barrier. This barrier may be made of any
rigid material.
Barrier protection is not necessary if the product is installed
above an underbench oven or similar appliance and/or if
the cupboard construction is such that the underside of the
cooktop is not accessible.
Figure 4
37mm
130mm min
490mm
570mm
19mm
gas supply
connection
130mm min
Medium burner 9.0 MJ/h 9.0 MJ/h 9.0 MJ/h 2 x 9.0 MJ/h 2 x 9.0 MJ/h
Large burner 12.1 MJ/h 12.1 MJ/h 12.1 MJ/h 12.1 MJ/h 12.1 MJ/h
Wok burner 14.4 MJ/h 14.4 MJ/h 14.4 MJ/h 14.4 MJ/h 14.4 MJ/h
Total MJ/h 40.6 MJ/h 40.6 MJ/h 40.6 MJ/h 49.6 MJ/h 49.6 MJ/h
Installation procedure
1. The bench cutout should be made as per cutout dimensions in
Table 2 and Figure 4.
2. Adjacent walls, cupboards and protection for combustible
materials: Ensure that the appliance is installed in accordance
with clauses 6.2.5 and 6.10.1.1 of AS/NZS 5601.1, or
clauses 6.9.1 and 6.9.5 of AS/NZS 5601.2 with regard
135mm
min
830mm
19mm
27mm
470mm
gas supply
connection
to clearances to combustible surfaces and materials, and
clearances to rangehoods and exhaust fans.
To ensure clearances of 200mm from burners to vertical
combustible surfaces observe the minimum distance
requirements shown in Figure 5.
Clearances to combustible surfaces may be reduced if
combustible surfaces are protected in accordance with clause
6.10.1.2 of AS/NZS 5601.1, or clause 6.9.2 of AS/NZS
5601.2.
NOTE: For installation into a standard 600mm width
benchtop the clearance specified can not be achieved
and combustible surfaces must be protected in
accordance with the above clauses.
10 TECHNICAL DATA Gas Cooktops Gas Cooktops INSTALLATION 11
120mm min
installation installation LPG conversion -
WARNING
TIPS & INFORMATION
TIPS & INFORMATION
DONG YANG regulator
Figure 5
110mm
115mm
4. Fitting the cooktop into the bench. Carry out as follows.
• Place the rubber seal provided around the edge of the hob.
NOTE: The rubber seal has talc powder applied to it’s
surface which should be wiped off with a damp cloth
after the unit has been installed.
Figure 6
rubber seal
benchtop
• Fit the pull-down clamps supplied to ensure that the
cooktop cannot move after installation.
Failure to fix the cooktop to the bench could result in loosening of
the gas connection through movement of the cooktop and a gas
leak may result.
• Use the 4 clamps and 4 screws supplied in the parts bag.
• To assemble, attach the 4 clamps to each corner of the
burner box via the screw provided.
• When placing the cooktop in the cut-out, swing the
clamps parallel with the box to avoid interference with the
cut-out.
• Position the cooktop so it is centred, then swing the
clamps under the benchtop and tighten.
hob
warning
clamp
burner box
screw
wall
Operation on NG/SNG
Regulator
An appliance regulator is provided. The regulator must be
positioned so that the pressure test nipple is accessible when
the appliance is installed. Connect the gas supply to the ½”
B.S.P. internal thread inlet of the regulator. Refer to ‘bench
cutout’ (Figure 4) for connection point position.
Regulators are supplied pre-adjusted and configured by the
component maker for use with Natural Gas. The appliance
installer is not required to make an adjustment to obtain the
correct outlet pressure setting.
An arrow on the base of the regulator indicates the direction
of gas flow when the inlet and outlet of the regulator is
oriented correctly. When the regulator has been fitted check
for leaks from the connections with soapy water.
Gas connection
This appliance is supplied for use with Natural Gas.
However, it can be converted for use with LPG. Refer to LP
conversion on pages 13-15.
Supply pipe sizing
The total hourly gas consumption for the appliance is shown
on the data label. The required supply pressure (i.e. at inlet
to appliance regulator) for each gas type is shown on the
data label, and given in Table 3. Use this information in
conjunction with the length of run, number of elbows, tees
and bends, the available service pressure and the supply
requirements of other installed appliances to determine
a suitable pipe size. For assistance in this matter refer to
the appropriate section of AS/NZS 5601.1 or
AS/NZS 5601.2.
An AGA certified class B or D flexible connection may be
used to connect the cooktop in accordance with AS/NZS
5601.1, in particular section 5.9 and clause 6.10.1.8, or
AS/NZS 5601.2, in particular section 2.11. Where a hose
assembly is used and the cooktop is in the installed position,
the hose assembly shall be suitable for connection to a fixed
consumer piping outlet located at a point 800 – 850mm
above the floor and in the region outside the width of the
appliance to a distance of 250mm. The point of connection
to consumer piping must be accessible with appliance
installed.
Elbow positioning
It is possible to reposition the elbow if required by loosening
the locking nut and elbow by using two spanners. Re-tighten
the entire assembly after the elbow has been repositioned.
When fitting elbow to appliance, ensure that the sealing
washer is fitted.
Checking the gas supply
1. Check the manometer zero point is correct.
2. Connect the manometer to the cooktop pressure point. This
is located on the regulator.
3. Turn on the gas supply and electricity and try to ignite
the gas.
tips & information
It will take additional time to light the gas for the first time as
air needs to be purged from the pipes.
4. With the appliance operating check the outlet pressure:
• when all burners of the appliance are operating
at maximum,
• when the smallest burner of the appliance
is operating at minimum.
Under these conditions the outlet pressure should not vary
from the nominal outlet pressure of 1.00kPa by more than
+/–0.20kPa.
If the regulator appears to not be performing satisfactorily,
then check the following points.
1. If the outlet pressure is consistently too low then the inlet
pressure may be too low and adjustment of an upstream
regulator may be needed, or an upstream regulator or
valve with insufficient flow capacity may be present in the
gas supply line. If this is suspected then it may be necessary
to repeat the checks whilst
measuring both the inlet and outlet pressure to determine
if the inlet pressure is in the range 1.13 – 5kPa.
2. Check that the regulator has been fitted to the gas supply
line in the correct orientation, the arrow on the base of the
body indicates the direction of gas flow.
Once these checks have been completed, if the regulator
still fails to perform in a satisfactory manner it should be
replaced.
tips & information
Refer to page 15 if you have been supplied with a
CHANT regulator.
This appliance is fitted with Natural Gas burner injectors.
Please follow the procedure below if a conversion to suit LP
gas is required.
injectors and 1 LPG sticker.
To convert to LPG
1. Remove the hotplate burners to access the hotplate
injectors. Replace the factory fitted NG injectors with the
appropriate injectors, as supplied (see Table 3).
2. Unscrew the hex nut from the regulator. The hex nut, brass
washer and nylon insert will disengage as
an assembly.
3. Unclip the nylon insert from the nut assembly by rotating the
insert ¼ turn, and pulling it free.
4. Turn over the insert, and clip back into position.
5. Refit the hex nut assembly to the regulator ensuring that it is fully
screwed down. The regulator is now set for connection to LP.
6. Turn on the gas supply and at each new connection check
for leaks using soapy water: each hotplate valve should be
turned on, one at a time, and the injector hole blanked off
for several seconds.
7. The operation of the regulator can be confirmed by
connecting a manometer to the pressure test point located
on the side of the regulator body adjacent to the outlet.
With the appliance operating check the outlet pressure
• when all burners of the appliance are operating
at maximum,
• when the smallest burner of the appliance is operating at
minimum.
Under these conditions the outlet pressure should not vary
from the nominal outlet pressure of 2.60kPa by more than
+/–0.52kPa.
8. If the regulator appears to not be performing satisfactorily
then check the following points.
• If the outlet pressure is consistently too low then the inlet
pressure may be too low and adjustment of an upstream
regulator may be needed, or an upstream regulator or
valve with insufficient flow capacity may be present in
the gas supply line. If this is suspected then it may be
necessary to repeat the checks whilst measuring both the
inlet and outlet pressure to determine if the inlet pressure
is in the range 2.75–7.00kPa.
• Check that the insert has been fitted correctly as per
diagram figure 7. Check that the hex nut is fully
screwed down.
The conversion kit contains appropriate LPG
12 USING YOUR COOKTOP Gas Cooktops Gas Cooktops LP CONVERSION - DONG YANG 13
LPG conversion -
TIPS & INFORMATION
LPG conversion -
DONG YANG regulator
• Check that the regulator has been fitted to the
gas supply line in the correct orientation, the arrow on
the base of the body indicates the direction of gas flow.
Once these checks have been completed, if the regulator
still fails to perform in a satisfactory manner it should be
replaced.
9. One by one, turn the knobs to minimum and screw in the
bypass screw (accessible when the knob is removed –
refer figure 11) until a small stable flame results. Turn the
knob to maximum and then back to minimum to ensure that
the correct minimum flame is maintained.
10. Attach the LPG sticker to the cooker, near the gas supply
inlet. Cover the Natural Gas label that is
factory fitted.
Table 3
NATURAL GAS
(Nominal test point pressure: 1.00kPa)
Injector size (mm) Gas consumption
BURNER TYPE
Small burner
Medium burner
Large burner
Wok burner
Figure 7
1.00
1.35
1.60 12.1 0.90 10.7
1.75 14.4 1.00 13.0
Hex nut
assembly, fully
screwed down
Hex nut assembly,
removed from regulator
and insert disassembled
(MJ/h)
5.1
9.0
LPG
(Nominal test point pressure: 2.60kPa)
Injector size (mm) Gas consumption
(MJ/h)
0.55
0.70
Insert oriented for natural
gas operation
Insert oriented for LPG
operation
4.0
6.5
CHANT regulator
tips & information
Refer to page 13-14 if you have been supplied with a
DONG YANG regulator.
This appliance is supplied set up for Natural Gas usage. A
conversion kit is included with the product for Universal LPG
usage. The conversion kit contains the appropriate injectors
and 1 LPG sticker.
Please follow the procedure below if a conversion to suit
UNIVERSAL LPG is required:
1. Remove the hotplate trivets, burner caps and burner crowns
to access the hotplate injectors. Replace the factory fitted
injectors with the appropriate injectors, as supplied. Refer
to injector orifice table for injector sizes. The injector size is
stamped on the side of the injector.
2. Unscrew the top hat nut from the regulator. The top hat nut
and control pressure spring assembly will disengage as an
assembly.
3. Unscrew the threaded pin from top hat.
4. Upturn threaded pin, so spring is free and screw pin back
into the top hat until firm.
5. Refit the top hat nut assembly to the regulator ensuring
that it is fully screwed down. The regulator is now set for
connection to LPG.
6. Turn on the gas supply and at each new connection check
for leaks using soapy water. Each hotplate valve should be
turned on, one at a time, and the injector hole blanked off
for several seconds.
7. The operation of the regulator can be confirmed by
connecting a manometer to the pressure test point located
on the side of the regulator body adjacent to the outlet.
With the appliance operating check the outlet pressure
• when all burners of the appliance are operating at
maximum,
• when the smallest burner of the appliance is operating
at minimum.
Under these conditions the outlet pressure should not vary
from the nominal outlet pressure of 2.60kPa by more than
±0.52kPa.
8. If the regulator appears to not be performing satisfactorily
then check the following points:
• If the outlet pressure is consistently too low then the
inlet pressure may be too low and adjustment of an
upstream regulator may be needed, or an upstream
regulator or valve with insufficient flow capacity may be
present in the gas supply line.
• If this is suspected then it may be necessary to repeat
the checks whilst measuring both the inlet and outlet
pressure to determine if the inlet pressure is in the range
2.75 – 7.00kPa.
• Check that the insert has been fitted correctly.
• Check that the turret screw is fully screwed down.
• Check that the regulator has been fitted to the gas
supply line in the correct orientation, the arrow on the
base of the body indicates the direction of gas flow.
Once these checks have been completed, if the regulator still
fails to perform in a satisfactory manner it should be replaced.
9. One by one, turn the knobs to minimum and screw in the
bypass screw (accessible when the knob is removed) until
a small stable flame results. Turn the knob to maximum and
then back to minimum to ensure that the correct minimum
flame is maintained.
10. Attach the LPG sticker to the cooker, near the gas supply
inlet. Cover the Natural Gas label that is
factory fitted.
Figure 8
A
top hat nut assembly
fully screwed down
C D
configuration for
natural gas
E F
G H
flame size adjusted to maximum
B
configuration
turn top hat
nut anticlockwise
and remove
for LPG
bypass screw
15
flame size adjusted to minimum
control knob shaft
14 LP CONVERSION - DONG YANG Gas Cooktops Gas Cooktops LP CONVERSION - CHANT 15
electrical connection testing appliance
WARNING
WARNING
operation
Battery connection
The battery used is a 1.5 Volt ‘AA’ Battery. This supplies the
power for the ignition system of the cooktop. To install, follow
the safety instructions as shown on Figure 9 below.
NOTE: Pay special attention to the orientation of the battery
when installing.
The battery supplied is a perishable item and not covered by
the warranty.
Electrical connection (220-240 Volts)
Where applicable, the appliance is supplied with a standard
7.5 Amp service cord terminated by a 3-pin plug for
connection to a standard household socket. The electrical
supply is required to power the electronic ignition system.
NOTE: It will be necessary for servicing purposes to
disconnect the electrical power supply. The power point
should therefore be accessible after the appliance is installed,
as specified in the local wiring regulations.
Diagram 1 is a schematic of the wiring in the appliance.
The weight of the unit is printed on the appliance packaging
label.
Diagram 1
1.5V battery models
Do not connect battery ignition
models to mains supply
WARNING
1.5V
DC
button
switch
1.50V
ignition
box
to burner spark plugsto burner spark plugs
Battery holder installation instructions
1. Locate a convenient position to mount battery holder,
keeping it away from hot surfaces.
warning
DO NOT attach it to the base of the cooktop.
2. Ensure mounting surface is clean.
3. Remove protective tape from rear of holder and stick
in place.
Figure 9
double-sided tape
Use of hose assembles
Ensure that the hose assembly is restrained from accidental
contact with the flue outlet of an underbench oven or any
other hot surface of an adjacent appliance.
After installation, test the appliance and ensure that it
operates correctly before handing it over to the customer.
The following procedure is recommended:
1. Turn on the gas and electricity supply and attempt ignition
on all burners, both separately and in combination. (For
correct procedure, refer to page 4). Note that additional
time needs to be allowed for the initial lighting as air has
to be purged from the pipes.
2. Observe the flame appearance on each burner. (Figure
10) If it is much larger or much smaller than expected, the
injector size and supply pressure require checking. Where
a flame is unsatisfactory, refer to the Troubleshooting
Guide (Page 6) to correct the fault. If the Troubleshooting
Guide does not solve the problem, call the Service
Centre.
3. When all the foregoing is satisfactory, check the turndown
(minimum or low) setting on each burner, as this may need
adjustment. Valves have a by pass controlling screw,
which may be accessed by removing the knob. This
screw will be located on a particular area of the valve.
(Refer figure 11). Normally, this will have been correctly
set at the factory for use on NG (Natural Gas) and should
not require adjustment.
If the appliance has been converted to LPG, then the
bypass screw will have to be screwed in until a small,
stable flame results.
Please ensure the supply pressure has been checked
PRIOR to any adjustment.
4. If the appliance cannot be adjusted to perform safely,
inform the customer of the problem and affix an
appropriate warning notice to the appliance. If the
fault appears to be dangerous the appliance should be
disconnected. If a minor fault exists, the customer may
wish to use the appliance while awaiting service.
If a fault cannot be fixed, please call the Service Centre.
Injector sizes required for various gas types are shown in
Table 3 (page 14). The appliance inlet pressure for each gas
type is also shown.
For model identification after installation, an additional data
plate sticker has been provided. This sticker is to
be stuck onto adjacent cabinetry.
Figure 10
Flame size adjusted to maximum
Flame size adjusted to minimum
Figure 11
Bypass screw
E
5. The customer should be advised that, in the event
of a fault, the local Service Organisation or the retailer
from whom the appliance was purchased should be
contacted.
6. When satisfied that the unit is operating correctly, turn off
and instruct the customer on correct operation as outlined
in this booklet. Ask the customer to operate the controls
to ensure that the correct procedure is understood.
warning
Servicing must only be carried out by an authorised
Disconnect from supply
before removing panel
220-240 volts AC
DANGER
A
220-240V
N
220-240V models
box
ignition
220-240V
knob ignition switches
service person.
E
16 ELECTRICAL CONNECTION Gas Cooktops Gas Cooktops TESTING 17
notes
Warranty
FOR SALES IN AUSTRALIA AND NEW ZEALAND
APPLIANCE: BUILT-IN OVEN, COOKTOP
AND FREESTANDING COOKERS
This document sets out the terms and conditions of the product
warranties for Electrolux Appliances. It is an important document.
Please keep it with your proof of purchase documents in a safe place
for future reference should you require service for your Appliance.
1. In this warranty:
(a) ‘acceptable quality’ as referred to in clause 10 of this warranty has
the same meaning referred to in the ACL;
(b) ‘ACL’ means Schedule 2 to the Competition and Consumer Act 2010;
(c) ‘Appliance’ means any Electrolux product purchased by you and
accompanied by this document;
(d) ‘ASC’ means Electrolux authorised service centres;
(e) ‘Electrolux’ means Electrolux Home Products Pty Ltd of 163
O’Riordan Street, Mascot NSW 2020, ABN 51 004 762 341 in
respect of Appliances purchased in Australia and Electrolux (NZ)
Limited (collectively ‘Electrolux’) of 3-5 Niall Burgess Road, Mount
Wellington, in respect of Appliances purchased in New Zealand;
(f) ‘major failure’ as referred to in clause 10 of this warranty has the
same meaning referred to in the ACL and includes a situation when
an Appliance cannot be repaired or it is uneconomic for Electrolux, at
its discretion, to repair an Appliance during the Warranty Period;
(g) ‘Warranty Period’ means the Appliance is warranted against
manufacturing defects in Australia for 24 months and in New Zealand
for 24 months, following the date of original purchase of the Appliance;
(h) ‘you’ means the purchaser of the Appliance not having purchased
the Appliance for re-sale, and ‘your’ has a corresponding meaning.
2. This warranty only applies to Appliances purchased and used in Australia
or New Zealand and used in normal domestic applications and is in
addition to (and does not exclude, restrict, or modify in any way) any
non-excludable statutory warranties in Australia or New Zealand.
3. During the Warranty Period Electrolux or its ASC will, at no extra charge
if your Appliance is readily accessible for service, without special
equipment and subject to these terms and conditions, repair or replace
any parts which it considers to be defective. Electrolux or its ASC may
use remanufactured parts to repair your Appliance. You agree that
any replaced Appliances or parts become the property of Electrolux.
This warranty does not apply to light globes, batteries, lters or similar
perishable parts.
4. Parts and Appliances not supplied by Electrolux are not covered by
this warranty.
5. To the extent permitted by law, you will bear the cost of transportation,
travel and delivery of the Appliance to and from Electrolux or its ASC. If
you reside outside of the service area, you will bear the cost of:
(a) travel of an authorised representative;
(b) transportation and delivery of the Appliance to and from Electrolux or
its ASC.
In all instances, unless the Appliance is transported by Electrolux or an
Electrolux authorised representative, the Appliance is transported at the
owner’s cost and risk while in transit to and from Electrolux or its ASC.
6. Proof of purchase is required before you can make a claim under
this warranty.
7. You may not make a claim under this warranty unless the defect claimed
is due to faulty or defective parts or workmanship. Electrolux is not liable
in the following situations (which are not exhaustive):
(a) the Appliance is damaged by:
(i) accident
(ii) misuse or abuse, including failure to properly maintain or service
(iii) normal wear and tear
(iv) power surges, electrical storm damage or incorrect power supply
(v) incomplete or improper installation
(vi) incorrect, improper or inappropriate operation
(vii) insect or vermin infestation
(viii) failure to comply with any additional instructions supplied with
the Appliance;
(b) the Appliance is modied without authority from Electrolux in writing;
(c) the Appliance’s serial number or warranty seal has been removed
or defaced;
(d) the Appliance was serviced or repaired by anyone other than
Electrolux, an authorised repairer or ASC.
8. This warranty, the contract to which it relates and the relationship
between you and Electrolux are governed by the law applicable where
the Appliance was purchased. Where the Appliance was purchased in
New Zealand for commercial purposes the Consumer Guarantee Act
does not apply.
9. To the extent permitted by law and subject to your non-excludable
statutory rights and warranties, Electrolux excludes all warranties and
liabilities (other than as contained in this document) including liability for
any loss or damage whether direct or indirect arising from your purchase,
use or non use of the Appliance.
10. For Appliances and services provided by Electrolux in Australia,
the Appliances come with a guarantee by Electrolux that cannot be
excluded under the ACL. You are entitled to a replacement or refund
for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the Appliance
repaired or replaced if the Appliance fails to be of acceptable quality and
the failure does not amount to a major failure.
The benets to you given by this warranty are in addition to your other
rights and remedies under a law in relation to the Appliances or services
to which the warranty relates.
11. At all times during the Warranty Period, Electrolux shall, at its discretion,
determine whether repair, replacement or refund will apply if an
Appliance has a valid warranty claim applicable to it.
12. For Appliances and services provided by Electrolux in New Zealand,
the Appliances come with a guarantee by Electrolux pursuant to the
provisions of the Consumer Guarantees Act, the Sale of Goods Act and
the Fair Trading Act.
13. To enquire about claiming under this warranty, please follow these steps:
(a) carefully check the operating instructions, user manual and the terms
of this warranty;
(b) have the model and serial number of the Appliance available;
(c) have the proof of purchase (e.g. an invoice) available;
(d) telephone the numbers shown below.
14. You accept that if you make a warranty claim, Electrolux and its ASC
may exchange information in relation to you to enable Electrolux to meet
its obligations under this warranty.
Before calling for service, please ensure that the steps listed in clause 13 above have been followed.
Important Notice
or to nd the address of your nearest
or to nd the address of your nearest
authorised service centre in New Zealand
18 NOTES Gas Cooktops Gas Cooktops WARRANTY 19
GOV_Warr_Sep15
FOR SERVICE
state service centre in Australia
PLEASE CALL 13 13 49
For the cost of a local call (Australia only)
FOR SERVICE
FREE CALL 0800 10 66 10
(New Zealand only)
SERVICE AUSTRALIA
ELECTROLUX HOME PRODUCTS
electrolux.com.au
SERVICE NEW ZEALAND
ELECTROLUX (NZ) Limited
electrolux.co.nz
FOR SPARE PARTS
or to nd the address of your nearest
state spare parts centre in Australia
PLEASE CALL 13 13 50
For the cost of a local call (Australia only)
FOR SPARE PARTS
or to nd the address of your nearest
state spare parts centre in New Zealand
FREE CALL 0800 10 66 20
(New Zealand only)
like to know more?
For further information on all appliances, or to obtain detailed
dimension and installation information, call into your Retailer,
phone or email our Customer Care team or visit our website:
Australia
phone: ..................................................1300 363 640
fax:.......................................................1800 350 067
email: ............................. customercare@electrolux.com.au
website ..................................... chef.com.au (Chef models)
........................westinghouse.com.au (Westinghouse models)
New Zealand
phone: ..................................................0800 234 234
fax:.......................................................0800 363 600
email: ................................customercare@electrolux.co.nz
website ............................simpson.co.nz (Simpson models)
........................westinghouse.co.nz (Westinghouse models)
Top service
Top Service encompasses the after sales service provided
by The Electrolux Group to consumers including delivery,
home service and spare parts.
Chef. We are part of the Electrolux Family.
To add a touch of professional inspiration to your home,
visit electrolux.com.au
©2016 Electrolux Home Products Pty Ltd
ABN 51 004 762 341
ECN 061879 ANC 305387212 Drawing 3053872_MD
Print code: CMAN_GASCOOK_UM_Apr16
Loading...