Westinghouse 6750900 Instruction Manual

Owner’s Manual

Outdoor Lighting Fixture
Installation Instructions

W-144

091404

Please write model number here for future reference: / Veuillez noter le numéro de mod­èle aux fins de référence ultérieure: / Por favor, incluya el número del modelo aquí para
futura referencia:

ASSEMBLY INSTRUCTIONS FOR OUTDOOR LIGHT FIXTURE

Congratulations on yourWestinghouse purchase. This fixture has been designed to give you
many years of beauty and service. Please email questions and comments to:
[e-mail].

NOTE: Carefully unpack fixture and parts. Make sure all parts are included before
discarding any packing materials (see figure 1).

WARRANTY INFORMATION

This Westinghouse Lighting Fixture is warranted against defects in material and workmanship for
a period of Five Years from purchase date. This warranty is in lieu of all other
warranties expressed or implied.

This warranty does not cover acts of nature such as lightning damage, or corrosion and
discoloration of components, nor does it cover damages caused through abuse, improper
installation, surges in electric current, or acts of third parties.

This warranty does not cover broken glass. If fixture is received with broken glass, please call
Westinghouse Lighting for free replacement.

This warranty does not cover costs of removing and re-installing the light fixture.

If this fixture fails for any reason covered by this warranty, simply return the fixture with a copy of
the original sales receipt, freight prepaid and Westinghouse Lighting, at its option, shall repair or
replace the fixture or refund the purchase price.

WARNING ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.

Read and follow instructions exactly as shown. If instructions are unclear,
do not proceed. Contact a qualified electrician. Read all instructions
before beginning. Proper wiring is essential for safe operation of this fix­ture. When cutting or drilling into walls or ceilings, do not damage electri­cal wiring, gas lines, or water lines. If any of the fixture or wiring compo­nents are damaged, do not install fixture. Return to place of purchase.

For fixtures provided with 75° C or 90° C supply wire warning only. (These
warnings are provided on the U.L. label and on the fixture carton.) Risk of
fire. Most dwellings built before 1985 have supply wires rated 60° C.
Consult a qualified electrician before installing.

NOTE: For fixture employing a grounded convenience outlet. This fixture
employs a grounded type receptacle and is not intended for connection to
a two wire ungrounded source of supply.

Applicable only to portable lamps:
To reduce the risk of electrical shock, all portable lamps have a polarized
plug (one blade is wider than the other). This plug will fit into a polarized
outlet only one way. If plug does not fit, reverse the plug. If it still does not
fit, contact a qualified electrician. Never use with an extension cord unless
plug can be fully plugged into the extension cord. Do not alter the plug.

2

FIGURE 1.

*OUTLET BOX (C)

GROUND WIRE

*OUTLET BOX

SCREWS (D)

GREEN
GROUNDING
SCREW (N)

CANOPY (L)

CAP NUTS (P)

CHAIN (J)

SIDE
HOLE (O)

MOUNTING
SCREWS (A)

MOUNTING
BAR (B)

HEX NUT (E)

LOCK WASHER (G)

NIPPLE (F)

CANOPY LOOP (H)

FIXTURE LOOP (K)

WIRE
CONNECTORS (M)

SCREWS (R)

Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.

3

TOP
ASSEMBLY (Q)
(MAY BE PRE­ASSEMBLED)

FIXTURE
CAGE (I)

*NOT SUPPLIED

MOUNTING AND WIRING INSTRUCTIONS

CAUTION: For fixtures labeled for outdoor and wet location use, provide a water-tight seal
between the fixture and the mounting surface by using silicone or similar caulking.

NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These
fixtures meet all UL specifications.

1. Turn off power at circuit box to avoid possible electric shock.

2. Thread mounting screws (A) into mounting bar (B) approximately 1/4 inch (see fig. 1).

3. Secure mounting bar (B) to outlet box (C) with outlet box screws (D) (not included).

4. Thread nipple (F) into canopy loop (H), place canopy (L) over nipple (F), then secure nipple
(F) with lock washer (G) and hex nut (E). May be preassembled (do not twist or kink wires).

5. Thread fixture loop (K) onto top assembly (Q) (see fig. 1).

6. Open one link on bottom end of chain (J). Attach to fixture loop (K). Securely close link on
chain (J).

7. Lace wires up through every other link on chain (J) then through canopy loop (H), canopy (L)
and nipple (F).

8. Open one link on top end of chain (J). Attach to canopy loop (H)
close link on chain (J).

9. Identify color coding of fixture wires (see fig. 2 on page 18).

10. To connect wires, take black fixture wire (group A from fig. 2) and place evenly against
black outlet box wire. Do not twist wires.

11. Fit wire connector (M from fig. 1) over wires and twist until there is a firm connection. If
wire connector (M) easily comes off, reattach and check again for a firm connection.

12. Repeat steps 2 and 3 with the white (group B from fig. 2) fixture wires and outlet box wires.

13. Partially thread green grounding screw (N) into side hole (O) on mounting bar (B)

14. Wrap ground wire from fixture around green grounding screw (N), leaving enough excess
wire to then connect ground wire and outlet box wire with wire connector.

15. Tighten green grounding screw (N). Do not over tighten.

16. Tuck wires inside outlet box (C).

and canopy (L)

. Securely

(see fig.1.)

FIXTURE ASSEMBLY INSTRUCTIONS

1. Secure fixture loop (H) to nipple (F) by raising canopy (L) to ceiling. Allow mounting
screws (A) to protrude through openings in canopy (L), and secure with cap nuts (P).

2. Install lamp (s). Do not exceed recommended wattage.

3. Turn power back on at circuit box.

4