Owner’s Manual
Outdoor Lighting Fixture
Installation Instructions
W-004
020204
Please write model number here for future reference: / Veuillez noter le numéro de modèle aux fins de référence ultérieure: / Por favor, incluya el número del modelo aquí para
futura referencia:
ASSEMBLY INSTRUCTIONS FOR OUTDOOR LIGHT FIXTURE
Congratulations on yourWestinghouse purchase. This fixture has been designed to give you
many years of beauty and service. Please email questions and comments to:
catalogroom@westinghouselighting.com.
NOTE: Carefully unpack fixture and parts. Make sure all parts are included before
discarding any packing materials (see figure 1).
WARRANTY INFORMATION
This Westinghouse Lighting Fixture is warranted against defects in material and workmanship for
a period of Five Years from purchase date. This warranty is in lieu of all other
warranties expressed or implied.
This warranty does not cover acts of nature such as lightning damage, or corrosion and
discoloration of components, nor does it cover damages caused through abuse, improper
installation, surges in electric current, or acts of third parties.
This warranty does not cover broken glass. If fixture is received with broken glass, please call
Westinghouse Lighting for free replacement.
This warranty does not cover costs of removing and re-installing the light fixture.
If this fixture fails for any reason covered by this warranty, simply return the fixture with a copy of
the original sales receipt, freight prepaid and Westinghouse Lighting, at its option, shall repair or
replace the fixture or refund the purchase price.
WARNINGS
ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.
Read and follow instructions exactly as shown. If instructions are
unclear, do not proceed. Contact a qualified electrician. Read all
instructions before beginning. Proper wiring is essential for safe
operation of this fixture. When cutting or drilling into walls or
ceilings, do not damage electrical wiring, gas lines, or water lines.
If any of the fixture or wiring components are damaged, do not
install fixture. Return to place of purchase.
For fixtures provided with 75° C or 90° C supply wire warning only.
(These warnings are provided on the U.L. label and on the fixture
carton.) Risk of fire. Most dwellings built before 1985 have supply
wires rated 60° C. Consult a qualified electrician before installing.
NOTE: For fixture employing a grounded convenience outlet.
CAUTION: “This fixture employs a grounded type receptacle and is
not intended for connection to a two wire ungrounded source of
supply.”
2
FIGURE 1.
*OUTLET
BOX (E)
GROUND
WIRE
WIRE
CONNECTORS (G)
MOUNTING
BAR (B)
*OUTLET BOX
SCREWS (F)
SIDE
HOLE (I)
GREEN
GROUNDING
SCREW (H)
NIPPLE (A)
NUT (D)
LOCK
WASHER (C)
CANOPY (J)
WASHER (K)
CAP NUT (L)
SIDE
PANELS (P)
PANEL
BRACKETS (O)
SQUARE
PANEL (M)
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
3
SIDE
PANELS (P)
FIXTURE
CAGE (N)
INTERIOR
CORNER
SLOTS (Q)
SCREWS (R)
*NOT SUPPLIED
MOUNTING AND WIRING INSTRUCTIONS
CAUTION: For fixtures labeled for outdoor and wet location use, provide a water-tight seal
between the fixture and the mounting surface by using silicone or similar caulking.
NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These
fixtures meet all UL specifications.
1. Turn off power at circuit box to avoid possible electric shock.
2. Thread nipple (A) into center hole on mounting bar (B) approximately
3. Secure lock washer (C) and nut (D) to nipple (A) on back side of mounting bar (B).
4. Secure mounting bar (B) to outlet box (E) with outlet box screws (F) (not included).
5. Identify color coding of fixture wires (see figure 2 on page 11).
6. To connect wires, take black fixture wire (group A from fig. 2) and place evenly against
black outlet box wire. Do not twist wires.
7. Fit wire connector (G from fig. 1) over wires and twist until there is a firm connection.
If wire connector (G) easily comes off, reattach and check again for a firm connection
(see fig. 1).
8.
Repeat steps 6 and 7 with the white (group B from fig. 2) fixture and outlet box wires.
9. Partially thread green grounding screw (H) into side hole (I) on mounting bar (B) (see fig. 1).
10. Wrap ground wire from fixture and ground wire (metal or green wire) from outlet box
(E) around green grounding screw (H) on mounting bar (B).
11. Tighten green grounding screw (H). Do not over tighten.
12. Tuck wires inside outlet box (E).
3/4 inch (see fig. 1).
FIXTURE ASSEMBLY INSTRUCTIONS
1. Raise canopy (J) to ceiling with nipple (A) protruding through center hole of canopy (J)
(see fig. 1).
2. Secure into place with washer (K) and cap nut (L).
3. Install lamp(s). Do not exceed recommended wattage.
4. Install square panel (M), textured sides facing outward, into bottom of fixture cage (N).
(see figure 1).
5. Center four panel brackets (O) on each edge of square panel (M) (see fig. 1).
6. Insert side panels (P), textured side facing outward, behind interior corner slots (Q) of
fixture cage (N).
NOTE: When side panels (P) are inserted into panel brackets (O), brackets will snap upward to
secure panels into place. If needed, gently push side panels (P) down until brackets snap into
place. After assembly, do not push on panels from the exterior of the fixture cage (N).
7. Raise fixture cage (N) to canopy (J), lining up holes in canopy (J) with holes in fixture
cage (N), and secure with screws (R).
8. Turn power back on at circuit box.
4