Westinghouse 6682600, 6682800, 6784600 Instruction Manual
Owner’s Manual
Outdoor Lighting Fixture
Installation Instructions
W-032
1/15/04
Please write model number here for future reference: / Veuillez noter le numéro de modèle aux fins de référence ultérieure: / Por favor, incluya el número del modelo aquí para
futura referencia:
ASSEMBLY INSTRUCTIONS FOR OUTDOOR LIGHT FIXTURE
Congratulations on yourWestinghouse purchase. This fixture has been designed to give you
many years of beauty and service. Please email questions and comments to:
catalogroom@westinghouselighting.com.
NOTE: Carefully unpack fixture and parts. Make sure all parts are included before
discarding any packing materials (see figure 1).
WARRANTY INFORMATION
This Westinghouse Lighting Fixture is warranted against defects in material and workmanship for
a period of Five Years from purchase date. This warranty is in lieu of all other
warranties expressed or implied.
This warranty does not cover acts of nature such as lightning damage, or corrosion and
discoloration of components, nor does it cover damages caused through abuse, improper
installation, surges in electric current, or acts of third parties.
This warranty does not cover broken glass. If fixture is received with broken glass, please call
Westinghouse Lighting for free replacement.
This warranty does not cover costs of removing and re-installing the light fixture.
If this fixture fails for any reason covered by this warranty, simply return the fixture with a copy of
the original sales receipt, freight prepaid and Westinghouse Lighting, at its option, shall repair or
replace the fixture or refund the purchase price.
WARNINGS
ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.
Read and follow instructions exactly as shown. If instructions are
unclear, do not proceed. Contact a qualified electrician. Read all
instructions before beginning. Proper wiring is essential for safe
operation of this fixture. When cutting or drilling into walls or
ceilings, do not damage electrical wiring, gas lines, or water lines.
If any of the fixture or wiring components are damaged, do not
install fixture. Return to place of purchase.
For fixtures provided with 75° C or 90° C supply wire warning only.
(These warnings are provided on the U.L. label and on the fixture
carton.) Risk of fire. Most dwellings built before 1985 have supply
wires rated 60° C. Consult a qualified electrician before installing.
NOTE: For fixture employing a grounded convenience outlet.
CAUTION: “This fixture employs a grounded type receptacle and is
not intended for connection to a two wire ungrounded source of
supply.”
2
FIGURE 1.
*OUTLET
BOX (D)
SIDE
HOLE (H)
SCREWS (K)
WASHER (N)
NUT (O)
GLASS
SHADE (P)
*OUTLET BOX
SCREWS (E)
FINIAL (M)
MOUNTING
SCREWS (I)
COVER (L)
GROUND
WIRE
CROSS
BAR (C)
GREEN
GROUNDING
SCREW (G)
WIRE
CONNECTORS (F)
BACK PLATE (B)
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
3
CAGE (J)
CAP NUTS (A)
*NOT SUPPLIED
MOUNTING AND WIRING INSTRUCTIONS
CAUTION: For fixtures labeled for outdoor and wet location use, provide a water-tight seal
between the fixture and the mounting surface by using silicone or similar caulking.
NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These
fixtures meet all UL specifications.
1. Turn off power at circuit box to avoid possible electric shock.
2. Remove cap nuts (A) from back plate (B) and remove cross bar (C) (see fig. 1).
3. Secure cross bar (C) to outlet box (D) with outlet box screws (E) (not included).
4. Identify color coding of fixture wires (see figure 2 on page 11).
5. To connect wires, take black fixture wire (group A from fig. 2) and place evenly against
black outlet box wire. Do not twist wires.
6. Fit wire connector (F from fig. 1) over wires and twist until there is a firm connection. If
wire connector (F) easily comes off, reattach wire connector (F) and check again for a firm
connection (see figure 1).
7. Repeat steps 5 and 6 with the white (group B from fig. 2) fixture wire and outlet box wires.
8. Partially thread green grounding screw (G) into side hole (H) on cross bar (C) (see fig. 1).
9. Wrap ground wire from fixture around green grounding screw (G), leaving enough excess
wire to then connect ground wire and outlet box wire with wire connector (F) (if applicable).
10. Tighten green grounding screw (G). Do not over tighten.
11. Tuck wires inside outlet box (D).
FIXTURE ASSEMBLY INSTRUCTIONS
1. Place back plate (B) over cross bar (C) (see fig. 1).
2. Secure into place with cap nuts (A).
3. Carefully place glass shade (P) into fixture cage (J).
4. Install lamp(s). Do not exceed recommended wattage.
5. Secure finial (M) to top of fixture cover (L) with washer (N) and nut (O).
6. Remove screws (K) from top of fixture cage (J).
7. Place fixture cover (L) over fixture cage (J) and secure with screws (K).
8. Turn power back on at circuit box.
4
Loading...