Westinghouse 6667700 Instruction Manual
Owner’s Manual
Indoor Lighting Fixture
Installation Instructions
W-023
01/15/04
Please write model number here for future reference: / Veuillez noter le numéro de modèle aux fins de référence ultérieure: / Por favor, incluya el número del modelo aquí para
futura referencia:
2
ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHT FIXTURE
Congratulations on yourWestinghouse purchase. This fixture has been designed to give you
many years of beauty and service. Please email questions and comments to:
catalogroom@westinghouselighting.com.
NOTE: Carefully unpack fixture and parts. Make sure all parts are included before
discarding any packing materials (see figure 1).
WARRANTY INFORMATION
This Westinghouse Lighting Fixture is warranted against defects in material and workmanship for
a period of Five Years from purchase date. This warranty is in lieu of all other
warranties expressed or implied.
This warranty does not cover acts of nature such as lightning damage, or corrosion and
discoloration of components, nor does it cover damages caused through abuse, improper
installation, surges in electric current, or acts of third parties.
This warranty does not cover broken glass. If fixture is received with broken glass, please call
Westinghouse Lighting for free replacement.
This warranty does not cover costs of removing and re-installing the light fixture.
If this fixture fails for any reason covered by this warranty, simply return the fixture with a copy of
the original sales receipt, freight prepaid and Westinghouse Lighting, at its option, shall repair or
replace the fixture or refund the purchase price.
WARNINGS
ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.
Read and follow instructions exactly as shown. If instructions are
unclear, do not proceed. Contact a qualified electrician. Read all
instructions before beginning. Proper wiring is essential for safe
operation of this fixture. When cutting or drilling into walls or
ceilings, do not damage electrical wiring, gas lines, or water lines.
If any of the fixture or wiring components are damaged, do not
install fixture. Return to place of purchase.
For fixtures provided with 75° C or 90° C supply wire warning only.
(These warnings are provided on the U.L. label and on the fixture
carton.) Risk of fire. Most dwellings built before 1985 have supply
wires rated 60° C. Consult a qualified electrician before installing.
NOTE: For fixture employing a grounded convenience outlet.
CAUTION: “This fixture employs a grounded type receptacle and is
not intended for connection to a two wire ungrounded source of
supply.”
3
FIGURE 1.
*NOT SUPPLIED
CANOPY WITH
INSULATION (H)
*OUTLET
BOX (C)
GLASS
SHADE (K)
THUMB
SCREWS (J)
MOUNTING
BAR (B)
SHADE
LIP (L)
KEY
SLOTS (I)
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
GREEN
GROUNDING
SCREW (F)
WIRE
CONNECTORS (E)
GROUND
WIRE
*OUTLET BOX
SCREWS (D)
MOUNTING
SCREWS (A)
SIDE
HOLE (G)
4
NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These
fixtures meet all UL specifications.
1. Turn off power at circuit box to avoid possible electric shock.
2. Thread mounting screws (A) into mounting bar (B) (see fig. 1) approximately
1
/4 inch.
3. Secure mounting bar (B) to outlet box (C) with outlet box screws (D) (not included).
4. To connect wires, take black fixture wire (group A from fig. 2 on page 11) and place evenly
against black outlet box wire. Do not twist wires.
5. Fit wire connector (E from fig. 1) over wires and twist until there is a firm connection.
If wire connector (E) easily comes off, reattach wire connector (E) and check again for a
firm connection (see figure 1).
6. Repeat steps 5 and 6 with the white (group B from fig. 2) fixture wire and outlet box wires.
7. Partially thread green grounding screw (F) into side hole (G) on mounting bar (B) (see fig.1).
8. Wrap ground wire from fixture and ground wire (metal or green wire) from outlet box
(C) around green grounding screw (F) on mounting bar (B).
9. Tighten green grounding screw (F). Do not over tighten.
10. Tuck wires inside outlet box (C).
MOUNTING AND WIRING INSTRUCTIONS
FIXTURE ASSEMBLY INSTRUCTIONS
1. Position canopy (H) over mounting screws (A) by aligning key slots (I) with mounting
screws (A).
2. Rotate canopy (H) until mounting screws (A) lock into narrow end of key slots (I).
3. Install lamp(s). Do not exceed recommended wattage.
4. Unscrew thumb screws (J) enough to insert glass shade (K) (with clear glass pointed
downward).
5. Carefully support glass shade (K) while securing thumb screws (J). Shade (K) is secure
when thumb screws (J) fit snugly under shade lip (L).
Loading...