Westinghouse 6486600 Instruction Manual
Owner’s Manual
Outdoor Lighting Fixture
Installation Instructions
W-010
01/14/04
Please write model number here for future reference: / Veuillez noter le numéro de modèle aux fins de référence ultérieure: / Por favor, incluya el número del modelo aquí para
futura referencia:
ASSEMBLY INSTRUCTIONS FOR OUTDOOR LIGHT FIXTURE
Congratulations on yourWestinghouse purchase. This fixture has been designed to give you
many years of beauty and service. Please email questions and comments to:
catalogroom@westinghouselighting.com.
NOTE: Carefully unpack fixture and parts. Make sure all parts are included before
discarding any packing materials (see figure 1).
WARRANTY INFORMATION
This Westinghouse Lighting Fixture is warranted against defects in material and workmanship for
a period of Five Years from purchase date. This warranty is in lieu of all other
warranties expressed or implied.
This warranty does not cover acts of nature such as lightning damage, or corrosion and
discoloration of components, nor does it cover damages caused through abuse, improper
installation, surges in electric current, or acts of third parties.
This warranty does not cover broken glass. If fixture is received with broken glass, please call
Westinghouse Lighting for free replacement.
This warranty does not cover costs of removing and re-installing the light fixture.
If this fixture fails for any reason covered by this warranty, simply return the fixture with a copy of
the original sales receipt, freight prepaid and Westinghouse Lighting, at its option, shall repair or
replace the fixture or refund the purchase price.
WARNING
NOTE: DO NOT INSTALL ON A POST THAT RESULTS
IN AVERTICAL RISE OF 25 FEET OR HIGHER.
WARNINGS
ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.
Read and follow instructions exactly as shown. If instructions are
unclear, do not proceed. Contact a qualified electrician. Read all
instructions before beginning. Proper wiring is essential for safe
operation of this fixture. When cutting or drilling into walls or
ceilings, do not damage electrical wiring, gas lines, or water lines.
If any of the fixture or wiring components are damaged, do not
install fixture. Return to place of purchase.
For fixtures provided with 75° C or 90° C supply wire warning only.
(These warnings are provided on the U.L. label and on the fixture
carton.) Risk of fire. Most dwellings built before 1985 have supply
wires rated 60° C. Consult a qualified electrician before installing.
NOTE: For fixture employing a grounded convenience outlet.
CAUTION: “This fixture employs a grounded type receptacle and is
not intended for connection to a two wire ungrounded source of
supply.”
2
FIGURE 1.
FINIAL (D)
WASHER (E)
COVER (F)
SUPPORT
FRAME (J)
FRAME
SCREWS (H)
FIXTURE
BODY (I)
SCREW (C)
SOCKET (G)
FITTER (A)
POST (B)
3
MOUNTING AND WIRING INSTRUCTIONS
CAUTION: For fixtures labeled for outdoor and wet location use, provide a water-tight seal
between the fixture and the mounting surface by using silicone or similar caulking.
NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These
fixtures meet all UL specifications.
1. Turn off power at circuit box to avoid possible electric shock.
NOTE: If post does not have mounting holes, follow step 2. Otherwise, skip step 2 and proceed
with step 3.
2. Place fitter (A) over post (B) (see figure1). Mark post using fitter holes as a guide. Remove
fitter, drill
3. Pull wires up from post (B) and thread through fitter (A).
4. Identify color coding of fixture wires (see figure 2 on page 11).
5. To connect wires, take black fixture wire (group A from figure 2) and place evenly against
black post wire. Do not twist wires.
6. Fit the wire connector over wires and screw the wire connector clockwise until you feel
a firmness. If wire connector easily comes off, reattach wire connector and check again
fora firm connection.
7. Repeat steps 5 and 6 with the white (group B from figure 2 ) fixture wire and post wires.
8. Place ground wire from fixture evenly against ground wire (metal or green wire) from
post (B).
9. Repeat step 6 for ground wires.
1
/8” hole through post at each mark.
FIXTURE ASSEMBLY INSTRUCTIONS
1. Remove finial (D), washer (E), and cover (F)
2. Remove frame screws (H) if assembled in fixture body (I).
3. Assemble support frame (J) to fixture body (I) using screws (H) (if applicable). NOTE: If
necessary, assemble support frame (J) to fixture body (I) with screws (H) protruding up from
the bottom of the holes while tightening nut at the top.
4. Install lamp(s). Do not exceed recommended wattage.
5. Replace cover (F), washer (E), and finial (D).
6. Place fitter (A) over post (B) and line up holes (see figure 1).
7. Secure with screws (C).
8. Turn on power at circuit box.
4
Loading...