Westinghouse 6222900, 6223000, 6228600, 6225200, 6224900 Instruction Manual

Owner’s Manual

Indoor Lighting Fixture
Installation Instructions

W-101

091811

Please write model number here for future reference: / Veuillez noter le numéro de mod­èle aux fins de référence ultérieure: / Por favor, incluya el número del modelo aquí para
futura referencia:

2

ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHT FIXTURE

NOTE: Carefully unpack fixture and parts. Make sure all parts are included before
discarding any packing materials (see figure 1).

WARRANTY INFORMATION

This Westinghouse Lighting Fixture is warranted against defects in material and workmanship for
a period of Five Years from purchase date. This warranty is in lieu of all other
warranties expressed or implied.

This warranty does not cover acts of nature such as lightning damage, or corrosion and
discoloration of components, nor does it cover damages caused through abuse, improper
installation, surges in electric current, or acts of third parties.

This warranty does not cover costs of removing and re-installing the light fixture.
If this fixture fails for any reason covered by this warranty, simply return the fixture with a copy of

the original sales receipt, freight prepaid and Westinghouse Lighting, at its option, shall repair or
replace the fixture or refund the purchase price.

WARNING: ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.

Read and follow instructions exactly as shown. If instructions are unclear,
do not proceed. Contact a qualified electrician. Read all instructions
before beginning. Proper wiring is essential for safe operation of this fix­ture. When cutting or drilling into walls or ceilings, do not damage electri­cal wiring, gas lines, or water lines. If any of the fixture or wiring compo­nents are damaged, do not install fixture. Return to place of purchase.

For fixtures provided with 75° C or 90° C supply wire warning only. (These
warnings are provided on the U.L. label and on the fixture carton.) Risk of
fire. Most dwellings built before 1985 have supply wires rated 60° C.
Consult a qualified electrician before installing.

NOTE: For fixture employing a grounded convenience outlet. This fixture
employs a grounded type receptacle and is not intended for connection to
a two wire ungrounded source of supply.

Applicable only to portable lamps:
To reduce the risk of electrical shock, all portable lamps have a polarized
plug (one blade is wider than the other). This plug will fit into a polarized
outlet only one way. If plug does not fit, reverse the plug. If it still does not
fit, contact a qualified electrician. Never use with an extension cord unless
plug can be fully plugged into the extension cord. Do not alter the plug.

Congratulations on your Westinghouse purchase. This fixture has been designed to give you many

years of beauty and service. For questions and comments, please visit www.westinghouselighting.

com/contact-us.

3

FIGURE 1.

*NOT SUPPLIED

Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.

*OUTLET

BOX (B)

WIRE
CONNECTORS (O)

GREEN
GROUNDING
SCREW (P)

GROUND
WIRE

SIDE
HOLE (Q)

MOUNTING
BAR (A)

CANOPY (N)

GLASS
SHADE (R)

HEX NUT (D)

LOCK WASHER (F)

THUMB
SCREWS (T)

SCREW COLLAR
RING (L)

SCREW
COLLAR (M)

RETAINING
RING (U)

HOLDER (S)

CHAIN (K)

FIXTURE LOOP (I)

BASE (H)

COLUMN (J)

*OUTLET BOX

SCREWS (C)

NIPPLE 1 (G1)

NIPPLE 2 (G2)

4

NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These
fixtures meet all UL specifications.

1. Turn off power at circuit box to avoid possible electric shock.

2. Secure mounting bar (A) to outlet box (B) with outlet box screws (C) (not included) (see fig. 1).

3. Thread hex nut (D) onto nipple 1 (E1) approximately 1/4 inch and insert lockwasher (F),
then thread nipple 1 (E1) onto mounting bar (A) and secure with hex nut (D).

4. Thread nipple 2 (G2) onto base (H) (carefully twist loop (I) to secure nipple 2 (G2) if
needed). Do not twist or kinkwires.

5. Slide column (J) down over nipple 2 (G2).

6. Open one link on bottom end of chain (K). Attach to loop (I). Securely close link on chain (K).

7. Thread screw collar ring (L) onto screw collar (M), then place canopy (N) over top of screw
collar (M).

8. Lace wires up through every other link on chain (K) then through screw collar (M) and
nipple 1 (E1).

9. Open one link on top end of chain (K). Attach to loop on screw collar (M). Securely close
link on chain (K).

10. Identify color coding of fixture wires (see fig. 2).

11. To connect wires, take black fixture wire (group A from fig. 3) and place evenly against
black outlet box wire. Do not twist wires.

12. Fit wire connector (O from fig. 1) over wires and twist until there is a firm connection. If
wire connector (O) easily comes off, reattach and check again for a firm connection.

13. Repeat steps 11 and 12 with the white (group B from fig. 3) fixture wires and outlet box
wires.

14. Partially thread green grounding screw (P) into side hole (Q) on mounting bar (A)

15. Wrap ground wire from fixture around green grounding screw (P), leaving enough excess
wire to then connect ground wire and outlet box wire with wire connector.

16. Tighten green grounding screw (P). Do not over tighten.

17. Tuckwires inside outlet box (B).

18. Remove screw collar ring (L) from screw collar (M).

19. Secure screw collar (M) to nipple 1 (E1).

20. Raise canopy (N) to ceiling and thread screw collar ring (L) to screw collar (M) and tighten
as necessary.

MOUNTING AND WIRING INSTRUCTIONS

FIXTURE ASSEMBLY INSTRUCTIONS

Warning: This fixture is for indoor use only.

1. Install lamp(s). Do not exceed recommended wattage.

2. Place glass shade(s) (R) into holder(s) (S) and secure with thumb screws (T) or retaining
ring(s) (U), whichever is applicable. Do not over tighten.

3. Turn power back on at circuit box.