! Tools required:
! Do not throw away packaging materials until assembly is complete.
! Assemble this item on a soft surface, such as cardboard or carpet, to protect fi nish.
! Proper assembly of this item requires 2 people.
Hardware
zig zag modular
assembly instructions
1
bolts 8x
3
dowel 24x
5
cam lock 6x
7
2
4mm hex key 1x
4
cam bolt 6x
6
metal rod 3x
8
5mm hex key 1x
9
lock washer 3x
10
threaded cap nut 3x
screws 3x
Anti tip kit 1x
Mounting Plate 2x
Nylon Strap 1x
Small Screw 2x Large Screw 2x
Page 1 of 79365115 - 03.13.09
Parts
zig zag modular
assembly instructions
A
C
E
G
2x
1x
1x
B
2x
D
1x
F
2x
H
2x
1x
I
1x
Page 2 of 79365115 - 03.13.09
zig zag modular
assembly instructions
1. Hold panel (B) against panel (C). Insert dowel (3) into holes as shown in the drawing below.
rmly together. Insert bolt (1) through panel (A)
and tighten with 4mm hex key (2). This will be the Bottom assembly.
B
C
3
2. Hold panel the remaining panel (B) against the remaining panel (C). Insert dowel (3) into holes as shown in
the drawing below.
and tighten with 4mm hex key (2). This will be the Top assembly.
Next, align these with panel (D). Press rmly together. Insert bolt (1) through panel (D)
A
2
1
1
D
C
B
3
Page 3 of 79365115 - 03.13.09
zig zag modular
3. Insert can bolt (4) into panel (E) and panel (I) as shown in the drawing below.
E
4
assembly instructions
I
4. Align panels (G) and panels (F). Insert dowels (3) as shown. Align panel (I), (H), and (E) as the drawing shows
below. Press rmly to make sure the panels are fully assembled.
I
G
3
F
H
G
F
3
E
Page 4 of 79365115 - 03.13.09
tighten with 5mm hex key (7).
E
zig zag modular
assembly instructions
at washer (8), lock washer (9), and cap nut (10).
I
6
10
9
8
7
Page 5 of 79365115 - 03.13.09
zig zag modular
assembly instructions
6. Insert dowels (3) into panels (B). Insert cam locks (5) into panels (B) and panels (C). Align the three assembled
rmly together. tighten cam locks (5) with a phillips head screwdriver. Stand
zig zag modular unit upright.
Top Assembly
C
D
B
5
3
H
I
E
C
A
B
Bottom Asssembly
Page 6 of 79365115 - 03.13.09
zig zag modular
assembly instructions
NOTICE: To prevent injury and property damage from unexpected tipping of furniture, we highly
recommend installation of the anti-tip kit included with this product.
Attaching unit to wall with anti-tip kits.
1. Determine where the unit is to be placed and mark location on the wall for the mounting bracket
screw holes. They should be placed approximatly 1” below the top on the back of the unit.
2. Attach the mounting bracket vertically to the wall by inserting the long screws provided through the
holes in the bracket and tightening securely using screwdriver. Screws must penetrate wall studs for
proper installation.
3. Next using the short screws attach the 2nd bracket to the back of the unit top.
4. Lace the nylon strap down through the brackets. Slide the thin end of the strap through the
receiving end of the nylon strap. Pull to tighten tower snug against wall.
Long screw
Short screw
Adjustable levelers are installed in the legs to
ooring. To adjust these levelers,
simply turn them counterclosckwise to raise the leg.
CARE INSTRUCTIONS
Hardware may loosen overtime. Periodically check that all connections are tight.
nish, avoid the use of chemicals and household cleaners.
Page 7 of 79365115 - 03.13.09
Loading...