West Elm Teak Bath Sconce Single Assembly Instruction
teak bath sconce single
Important Safety Instructions:
·Stud mounting is recommended. Use proper hardware for your wall type. When in doubt consult your local hardware
store. For your safety, it is strongly recommended that two people hang the lamp.
·Electric bulb should be centered inside the pendant shade, making sure it does not touch the outer sides.
·These instructions are provided for your safety. It is important that they are read carefully and completely before
assembling xture.
·This xture has been rated for up to (1) 60-watt TYPE B bulb (not included). To avoid the risk of re, do not exceed the
recommended wattage.
Warning:
·To reduce the risk of re, electrical shock or personal injury, always turn o
and unplug lamp and allow it to cool prior to replacing light bulb.
·Do not touch bulb when xture is turned on. Do not look directly at lit bulb.
·Keep ammable materials away from lit bulb.
Pre-assembly:
·Remove all parts and hardware from box along with any plastic protective packaging.
·Do not discard any contents until after assembly is complete to avoid accidentally discarding small parts or hardware.
·For your safety and convenience, assembly by two people is recommended
assembly instructions
Parts Enclosed:
A
• (1) Mounting plate (J)
• (1) Canopy (L)
• (1) Lamp Socket (I)
• (1) Socket Ring (F)
• (1) Screw Cap (K)
• (1) Glass Shade (H)
Hardware Included:
• (1) Mounting screws (C)
• (2) Green ground screws (B)
B
C
D
wire caps 3x
grounding screw
mounting screws 1x
• (3) Plastic wire caps (A)
• (4) Canopy screws ( D )
To install you will need:
canopy screws
• Electrical tape
• Screwdriver
To Assemble:
1. SHUT OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN
FUSE BOX/CIRCUIT BREAKER.
2. Carefully unpack all xture parts and hardware and lay out
on a clear workspace.
3. Carefully inspect the chandelier's xture wires. The
NEUTRAL FIXTURE WIRE is white or marked “N”. The HOT
FIXTURE WIRE is black or marked “L”. The yellow-green or bare
wire is the GROUND WIRE.
2x
F
4x
L
A
D
H
K
B
I
5626221 - 03/08
C
page 1 of 2
J
teak bath sconce single
bare wire). Fasten each together with a plastic wire connector (A) and wrap the connection with electrical tape. Be
sure that no wire strands are exposed. If your outlet box DOES NOT have a GROUND WIRE, be sure to insert the
the ground screw. IT IS IMPERATIVE THAT THE OUTLET BOX IN YOUR HOME BE PROPERLY GROUNDED.
5. Connect the NEUTRAL FIXTURE WIRE to the NEUTRAL JUNCTION BOX WIRE (white). Fasten each together with a
plastic wire connector (A) and wrap the connection with electrical tape. Be sure no wire strands are exposed.
6. Connect the HOT FIXTURE WIRE to the HOT JUNCTION BOX WIRE (black). Fasten each together with a plastic wire
connector (A) and wrap the connection with electrical tape. Be sure no wire strands are exposed. DO NOT REVERSE
THE HOT AND NEUTRAL CONNECTIONS OR SAFETY WILL BE COMPROMISED.
7. Gently tuck the wire connections neatly into the ceiling junction box.
8. Attach the mounting plate (L) to the ceiling outlet box using the enclosed mounting screws (C). Tighten screws
with a screwdriver.
9. Pull canopy (J) up over the mounting plate (L), align the hole in the mounting plate with the hole in the canopy.
10. Insert the canopy screw (D) tighten with a screwdriver.
11. Unscrew sockets ring (F) from the socket.
12. Place glass shade (H) on socket (I).
13. Place the metal ring (G) onto the socket (I).
14. Screw on the socket rings (F) and tighten with wrench.
assembly instructions
Completing the Assembly:
1. Insert (1) 60-watt Type B bulb (not included) into the socket . DO NOT EXCEED SPECIFIED WATTAGE.
3. Assembly is complete.
Care Instructions:
• Wipe clean using a soft, dry cloth or static duster.
5626221 - 03/08
page 2 of 2
Loading...