West Elm Glass Jar Pendant Tall, Tall Glass Jar Pendant Assembly Instruction
Important Safety Instructions:
•These instructions are provided for your safety. It is very important that they are read carefully and com
pletely before beginning the installation of this lighting xture.
•THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODES BY A
PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS IN
VOLVED.
•We strongly recommend that a professional electrician install all direct wire xtures.
•This xture has been rated for up to (1) 60-Watt maximum Type A standard incandescent light bulbs (not
included) or 13-watt compact uorescent bulb (included). To avoid the risk of re, do not exceed the rec
ommended lamp wattage.
•The lighting xture is meant for indoor use. It must be connected only to 3-wire, single-phase electrical sup
ply systems (provided with Ground wire or equivalent protection system).
• Save this instruction.
WARNING:
• To reduce the risk of re, electrical shock or personal injury,
always turn o light xture and unplug, allow
ing it to cool prior to replacing light bulb.
• Do not touch bulb when xture is turned on.
• Do not look directly at lit bulb. Keep ammable materials
away from lit bulb.
SHUT OFF ALL THE MAIN ECLECTRICAL SUPPLY FROM THE
FUSE BOX / CIRCUIT BREAKER
Pre-assembly:
•Remove all parts and hardware from box along with any plastic protective packaging. Do not discard any
contents until after assembly is complete to avoid accidentally discarding small parts or hardware.
•For your safety and convenience, assembly by two people is recommended.
PA RTS INCLUDED: HARDWARE ENCLOSED: TOOLS REQUIRED (not included)
(1)Glass bottle (A) (1) Green ground screw (a) 1.Electrical tape
(1)Socket (B) (2) Mounting screws (b) 2.Screwdriver
(1)Metal Assembly Part (C) (3) Plastic wire connectors (c) 3.Two peoples recommended
(2)Canopy (D) (2) Headless screws (d)
(1)Mounting Plate (E) (3) Worm screws (e)
To Assemble:
1.Carefully unpack all xture parts and hardware and lay them on a clean workspace.
2.Gently pull wiring down from ceiling junction box and allow the lamp to hang.
3.Carefully inspect the pendant’s xture wires. The NEUTRAL FIXTURE WIRE is white. The HOT FIXTURE WIRE
is black. And the GROUND WIRE is green.
4.Attach the Ground Wire from the xture to the Ground Junction Box Wire from the outlet (usually green or
bare wire). Fasten each together with a Plastic Wire Connector (c) and wrap the connection with electrical
tape. Be sure that no wire strands are exposed. If your outlet box DOES NOT have a GROUND WIRE, be sure
to insert the Green Ground Screw (a) into the mounting Plate (E) facing DOWN, and wrap the xture’s bare
ground bare ground wire around the green Ground Screw (a). IT IS IMPERATEIVE THAT THE OUTLET BOX IN
YOUR HOME BE PROPERLY GROUNDED.
5.Connect the NEUTRAL FIXTURE WIRE to the NEUTRAL JUNCTION BOX WIRE (usually white). Fasten each
together with a Plastic Wire Connector (c) and wrap the connection with electrical tape. Be sure no wire
strands are exposed.
6.Connect the HOT FIXTURE WIRE to the HOT JUNCTION BOX WIRE (usually black). Fasten each together with
a Plastic Wire Connector (c) and wrap the connection with electrical tape. Be sure no wire strands are ex
posed. DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS OR SAFETY WILL BE COMPROMISED.
7.Gently tuck the wire connections neatly into the ceiling junction box.
8.Attach the Mounting Plate (E) to the ceiling outlet box using the enclosed Mounting Screws (b). Tighten
screws with a screwdriver.
9.Pull Canopy (D) up over the Mounting Plate (E), screw the headless screws (d) into the Mounting Plate (E)
by screwdriver until tighten.
10. Insert a bulb-Max 60 watt maximum TYPE A standard incandescent light bulb (not included) or 13-watt
compact uorescent bulb into the socket (B). DO NOT EXCEED SPECIFIED WATTA GE.
11. Insert a Glass bottle (A) into the Metal assembly part (C), screw the worm screws (e) into the Metal assem
bly part (C). Tighten the worm screws (e) with a screwdriver.
12. Restore power to junction box and test xture.
Care instructions:
• Wipe clean with a soft, dry cloth or static duster.
• Always avoid the use of harsh chemicals or abrasive cleaners as they may cause damage to the xture’s n
ish
Loading...