: rolling storage unit 3x4
assembly instructions
!
CAUTION
To prevent injury and property damage from unexpected tipping of furniture, we highly recommend installation of
the two (2) sets of overbalance protection hardware included with this product.
6889810/6813257/6813398/9740754/9740523 - 07/07
page 1 of 12
: rolling storage unit 3x4
! Tools required:
! Do not throw away packaging materials until assembly is complete.
! Assemble this item on a soft surface, such as cardboard or carpet, to protect the finish.
! Proper assembly of this piece requires two people.
A
assembly instructions
bolt: 5/16”DIA x 3”
B
cam: 1/4”DIA x 1 3/8”
12x
D
metal washer
8x
F
screw: 5/16”DIA x 1”
20x
C
E
G
8x
cam lock
lock washer
allen key
12x
8x
1x
H
6889810/6813257/6813398/9740754/9740523 - 07/07
snap-lock
6x
page 2 of 12
: rolling storage unit 3x4
1. Place one of the two side panels on its side as shown.
2. Screw cam (B) in holes shown. Tighten with a flat head screwdriver.
assembly instructions
2x
B
6889810/6813257/6813398/9740754/9740523 - 07/07
page 3 of 12
: rolling storage unit 3x4
assembly instructions
3. Attach the center shelf to the side panel and insert cam locks (C) into holes on the bottom of the shelf.
Tighten with a philip’s head screwdriver.
2x
C
6889810/6813257/6813398/9740754/9740523 - 07/07
page 4 of 12
: rolling storage unit 3x4
4. Insert dowels on upper and lower shelves into the other holes in the side panel.
assembly instructions
6889810/6813257/6813398/9740754/9740523 - 07/07
page 5 of 12
: rolling storage unit 3x4
assembly instructions
5. Repeat steps 1 through 4 on one inner panel and attach it to the other side of the three shelves.
6889810/6813257/6813398/9740754/9740523 - 07/07
page 6 of 12
: rolling storage unit 3x4
6. Repeat these steps with the remaining inner panel, side pane l and shelves as shown below.
assembly instructions
6889810/6813257/6813398/9740754/9740523 - 07/07
page 7 of 12
: rolling storage unit 3x4
assembly instructions
7. Attach the bottom panel to the side and inner panels with bolts (A), metal washers (D) and lock washers (E).
Tighten with the allen key (G).
E
A
G
D
6889810/6813257/6813398/9740754/9740523 - 07/07
8x
page 8 of 12
: rolling storage unit 3x4
assembly instructions
8. (OPTIONAL) Attach the 5 casters to the bottom panel with screws (F). Place 4 locking casters at corners and 1
non-locking caster in center. Tighten with philips head screwdriver.
5x
F
6889810/6813257/6813398/9740754/9740523 - 07/07
page 9 of 12
: rolling storage unit 3x4
assembly instructions
7. Set the storage unit upright.
8. Using a philips head screwdriver, screw snap-locks (H) into holes on top of side and inner panels.
6889810/6813257/6813398/9740754/9740523 - 07/07
6x
H
page 10 of 12
: rolling storage unit 3x4
assembly instructions
10. Align the holes on the top panel with the snap-lock pegs on the top of the inner and side panels. Ensure fingers and
body parts are clear of the connecting pieces. Firmly press down on the top panel until each peg snaps into place.
While this is a secure connection for assembly, this item should
not be lifted by the top panel for your safety, as it could
disengage from the rest of the shelving unit.
Snap-lock (patent pending) technology, exclusive to west elm, is
used in this product to enable quick and easy assembly
without visible hardware.
CARE INSTRUCTIONS. Hardware may loosen over time. Periodically check that all connections are tight.
Wipe with a soft, dry cloth. To protect the finish, avoid the use of all chemicals
and household cleaners.
6889810/6813257/6813398/9740754/9740523 - 07/07
page 11 of 12
: rolling storage unit 3x4
assembly instructions
OVER BALANCE. To prevent injury and property damage from unexpected tipping of furniture, we highly recommend
installation of the two (2) sets of overbalance protection hardware included with this product.
1. Attach the two mounting brackets horizontally to the top back edge of the furniture. Insert the
short screws through the holes in the bracket and tighten securely using screwdriver.
2. Determine where the furniture is to be placed and mark location on the wall for the other two
mounting bracket screw holes. It should be placed approximately 2” below the bracket mounted
to the furniture.
3. Attach the two mounting brackets vertically to the wall by inserting the long screws provided through
the holes in the bracket and tightening securely using screwdriver.
4. Place the furniture so the brackets on the back edge are in line with the brackets on the wall.
5. Lace an end of the nylon restraint strap down through each bracket. Bring both ends together
and slide the thin end of the strap through the receiving end of the strap until snug.
6. Check to make sure the strap is securely laced and locked to the brackets.
7. Repeat steps 5 and 6 for the second bracket set.
wall
6889810/6813257/6813398/9740754/9740523 - 07/07
back side
page 12 of 12
Loading...