newkirk media stand
assembly instructions
!
CAUTION
The top shelf of this cart/stand is intended for use with: Plasma/HD televisions having a maximum screen size of 42 inches and weight of 00 lbs; or
Tube televisions having a maximum screen size of 27 inches and weight of 95 lbs.
! Tools required:
! Do not throw away packaging materials until assembly is complete.
! Assemble this item on a soft surface, such as cardboard or carpet, to protect nish.
! Proper assembly of this item requires 2 people.
! This item comes in two boxes containing the back panel and the stand.
A B
bolt (6mm dia x 50mm) 2x
C D
metal washer 20x
E F
allen key x
G
bolt (6mm dia x 22mm) 8x
lock washer 20x
metal support 2x
H
cam lock 8x cam bolt 8x
Page of 69700923 - 06/07
newkirk media stand
assembly instructions
. Remove drawers from drawer unit. Lift up/push down plastic levers on opposite sides to release drawers while pulling out.
Facing the drawers, the left lever will need to be pushed up and the right lever will need to be pushed down at the same time while
pulling the drawer out. (Note : when handling the levers be aware that these may be greasy).
2. Fasten center foot to drawer unit using metal washers (C), lock washers (D), and bolts (A) in order as shown. Tighten bolts
using allen key (E).
3. Fasten side panels to drawer unit using metal washers (C), lock washers (D), and bolts (B) in order as shown. Tighten bolts
using allen key (E).
D
B
E
Page 2 of 69700923 - 06/07
newkirk media stand
assembly instructions
4. Screw cam bolts (H) into drawer unit as shown. Insert cam locks (G) into holes in center panel, making sure the arrow on the
cam locks points towards the hole in the edge of the panel. Set top panel onto side panel, tting cam bolt into cam locks. Tighten
cam locks with a Phillips screwdriver.
Page 3 of 69700923 - 06/07
newkirk media stand
assembly instructions
5. Screw cam bolts (H) into top panel. Insert cam locks (G) into holes in side panels, making sure the arrow on the cam locks
points towards the hole in the edge of the panel. Set top panel onto side panel, tting cam bolt into cam locks. Tighten cam locks
with a Phillips screwdriver.
H
6. Insert drawers into drawer unit.
G
Page 4 of 69700923 - 06/07
newkirk media stand
assembly instructions
7. Fasten back panel to side panels through metal support (F) using metal washers (C), lock washers (D), and bolts (B) in order as
shown. Tighten bolts using allen key (E).
CARE INSTRUCTIONS
Hardware may loosen over time. Periodically check that all connections are tight.
Wipe with a soft, dry cloth. To protect nish, avoid the use of chemicals and household cleaners.
Page 5 of 69700923 - 06/07
newkirk media stand
assembly instructions
OVER BALANCE To prevent injury and property damage from unexpected tipping of furniture, we highly recommend
installation of the two (2) sets of overbalance protection hardware included with this product.
1. Attach the two mounting brackets horizontally to the top back edge of the furniture. Insert the
short screws through the holes in the bracket and tighten securely using screwdriver.
2. Determine where the furniture is to be placed and mark location on the wall for the other two
mounting bracket screw holes. It should be placed approximately 2” below the bracket mounted
to the furniture.
3. Attach the two mounting brackets vertically to the wall by inserting the long screws provided through
the holes in the bracket and tightening securely using screwdriver.
4. Place the furniture so the brackets on the back edge are in line with the brackets on the wall.
5. Lace an end of the nylon restraint strap down through each bracket. Bring both ends together
and slide the thin end of the strap through the receiving end of the strap until snug.
6. Check to make sure the strap is securely laced and locked to the brackets.
7. Repeat steps 5 and 6 for the second bracket set.
wall
back side
Page 6 of 69700923 - 06/07
Loading...