West Elm Modular Lateral File Cabinet Assembly Instruction

modular lateral file cabinet
assembly instructions
! Tool required: ! Do not throw away packaging materials until assembly is complete. ! Assemble this item on a soft surface, such as: cardboard or carpet to protect finish. ! Proper assembly of this item requires 2 people.
Hardware
K
File bar 8x
O
Bolt 11x
S
T
Cam house 8x Cam bolt 8x
Flat washer 11x Lock washer 11x
U
NM
Q
Screw M6x30 12x
8600660-3.26.09
Screw M4x25 16x
Allen key 1x
Page 1 of 7
modular lateral file cabinet
assembly instructions
Parts
8600660-3.26.09
Page 2 of 7
modular lateral file cabinet
assembly instructions
1. Unfold end/back panel (A). Put cam bolt (N) into pre-installed inserts in each end panel at the front as shown below. Tighten cam bolts (N) with Phillips head screw driver.
A
N
A
2. Assemble center partition (B) and bottom rail (C) with end/back panels (A) by aligning pre-drilled holes in center partition (B) and bottom rail (C) with cam bolt (N) assembled in step 1. Put cam house (M) in pre-drilled hole at each end of center partition (B) and bottom rail (C) as shown below. Tighten cam house (M) with allen key (U).
8600660-3.26.09
A
B
C
M
Page 3 of 7
modular lateral file cabinet
assembly instructions
3. Attach bottom back rail (D) to back panels (A) with three bolts (O), lock washers (Q) and washers (P) as shown below. Tighten all bolts (O) with allen key (U).
A
P
Q
O
D
4. Assemble bottom frame (E) with bottom rail (C) and bottom back rail (D) with bolts (O), lock washers (Q) and washers (P) as shown below. Tighten all bolts (O) with allen key (U).
8600660-3.26.09
Page 4 of 7
modular lateral file cabinet
assembly instructions
5. Insert four cam bolts (N) into pre-drilled inserts at corners of top (F) as shown below. Tighten cam bolts (N) with Phillips head screw driver.
6. Carefully ip over top (F) and assemble with end/back panels (A) by aligning cam bolts on top (F) with pre-drilled holes in end/back panels (A). Insert four cam houses (M) into pre-drilled holes on end/back panels (A) as shown below. Tighten cam house (M) with allen key (U).
8600660-3.26.09
Page 5 of 7
modular lateral file cabinet
assembly instructions
7. Unfold upper drawer box (H). Slide drawer bottom panel (J) into the drawer box groove on back side of drawer front (G) with exposed edge of drawer bottom panel (J). Run 3 screws (S) through drawer box (H) to each side of drawer front (G), tighten screws (S) with allen key (U). Put two drawer support rails (L) in the notches on back side of assembled drawer. Run two screws (T) through pre-drilled holes in each end of drawer support rail (L) as shown below. Tighten all screws (T) with Philips head screw driver.
8. Repeat step for lower drawer box (I) assembly.
9. Install le bars (K) into the walls of upper drawer box (H) and lower drawer box (I) as shown.
Upper Drawer Box (H) Lower Drawer Box (I)
8600660-3.26.09
Page 6 of 7
modular lateral file cabinet
assembly instructions
10. Install upper drawer box (H) and lower drawer box (I) into the cabinet as shown.
H
I
CARE INSTRUCTIONS Hardware may loosen over time. Periodically check that all connections are tight. Wipe with a soft, dry cloth. To protect nish, avoid the use of chemicals and household cleaners.
8600660-3.26.09
Page 7 of 7
Loading...