West Elm Globe Pendant Assembly Instruction
globe pendant
Important Safety Instructions:
·Stud mounting is recommended. Use proper hardware for your wall type. When in doubt consult your local hardware
store. For your safety, it is strongly recommended that two people hang the lamp.
·Electric bulb should be centered inside the pendant shade, making sure it does not touch the outer sides.
·These instructions are provided for your safety. It is important that they are read carefully and completely before
assembling xture.
·This xture has been rated for up to (1) 60-watt maximum TYPE A standard bulb (not included). To avoid the risk of re,
do not exceed the recommended wattage.
Warning:
·To reduce the risk of re, electrical shock or personal injury, always turn o
and unplug lamp and allow it to cool prior to replacing light bulb.
·Do not touch bulb when xture is turned on. Do not look directly at lit bulb.
·Keep ammable materials away from lit bulb.
Pre-assembly:
·Remove all parts and hardware from box along with any plastic protective packaging.
·Do not discard any contents until after assembly is complete to avoid accidentally discarding small parts or hardware.
·For your safety and convenience, assembly by two people is recommended
assembly instructions
Parts Enclosed:
A
• (1) Mounting plate (E)
• (1) Canopy (F)
• (1) Screw cap (H)
B
wire caps 3x
• (1) Lamp Socket (G)
• (1) Socket Ring (J)
• (1) Shade Canopy (I)
• (1) Glass Shade(K)
Hardware Included:
• (1) Mounting screws (C)
C
D
grounding screw
mounting screws 1x
2x
• (2) Green ground screws (B)
• (3) Plastic wire caps (A)
canopy screws
4x
• (4) Canopy screws ( D )
To install you will need:
• Electrical tape
• Screwdriver
To Assemble:
1. SHUT OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT
BREAKER.
2. Carefully unpack all xture parts and hardware and lay out on a clear workspace.
3. Place the shade canopy (I) onto the lamp socket (G)
4. Screw the metal ring (J) onto the lamp socket (G)
5. Hang up the glass shade (K) on the shade canopy (I).
6. Tighten the shade canopy (I) by the screw cap (H).
7. Carefully inspect the chandelier's xture wires. The NEUTRAL FIXTURE WIRE is
white or marked “N”. The HOT FIXTURE WIRE is black or marked “L”. The
yellow-green or bare wire is the GROUND WIRE.
A
E
B
C
D
F
G
H
I
J
K
5388285/5567557 - 03/08
page 1 of 2
globe pendant
8. Attach the GROUND WIRE from the xture to the GROUND JUNCTION BOX WIRE from the outlet (usually green or bare
wire). Fasten each together with a plastic wire connector (A) and wrap the connection with electrical tape. Be sure that
no wire strands are exposed. If your outlet box DOES NOT have a GROUND WIRE, be sure to insert the green ground
screw (B) into the mounting plate (E) facing DOWN, and wrap the xture's bare ground wire around the ground screw. IT
IS IMPERATIVE THAT THE OUTLET BOX IN YOUR HOME BE PROPERLY GROUNDED.
9. Connect the NEUTRAL FIXTURE WIRE to the NEUTRAL JUNCTION BOX WIRE ( white). Fasten each together with a
plastic wire connector (A) and wrap the connection with electrical tape. Be sure no wire strands are exposed.
10. Connect the HOT FIXTURE WIRE to the HOT JUNCTION BOX WIRE ( black). Fasten each together with a plastic wire
connector (A) and wrap the connection with electrical tape. Be sure no wire strands are exposed. DO NOT REVERSE THE
HOT AND NEUTRAL CONNECTIONS OR SAFETY WILL BE COMPROMISED.
11. Gently tuck the wire connections neatly into the ceiling junction box.
12. Attach the mounting plate (E) to the ceiling outlet box using the enclosed mounting screws (C). Tighten screws with
a screwdriver.
13. Pull canopy (F) up over the mounting plate (E), align the hole in the mounting plate with the hole in the canopy.
14. Using the enclosed mounting screws (D). Tighten screws with a screwdriver.
Completing the Assembly:
1. Insert (1) 60-watt Type A bulbs (not included) into the socket . DO NOT EXCEED SPECIFIED WATTAGE.
2. Restore power to junction box and test xture.
3. Assembly is complete.
Care Instructions:
• Wipe clean using a soft, dry cloth or static duster.
• Always avoid the use of harsh chemicals and abrasives to clean xture as they may damage the nish.
assembly instructions
5388285/5567557 - 03/08
page 2 of 2
Loading...