West Elm Flat Stock Metal Double Sconce Assembly Instruction

flat stock metal double sconce

Important Safety Instructions:

• These instructions are provided for your safety. It is important that they are read carefully and completely before
installing the chandelier.

• We strongly recommend that a professional electrician install all direct wire fixtures.

• This fixture has been rated for up to (2)

fire, do not exceed the recommended wattage.

Pre-assembly:

• Remove all parts and hardware from box along with any plastic packaging. Do not discard any
contents until after assembly is complete to avoid accidentally discarding small parts or hardware.

• For your safety and convenience, assembly by two people is recommended.

Parts Enclosed:

(1) Mounting plate (J)

•

(1) Canopy (I)

•

(2) Socket Ring (F)

•

(2) Metal Tube (G)

•

(1) Metal plate (K)

•

(2) Glass Shade (H)

•

Hardware Included:

• Mounting screws (D)

• Green ground screw (B)

• Plastic wire connectors (A)

• Canopy screws (C)

• Wrench (E)

To install you will need:

• Electrical tape

• Screwdriver

60-watt TYPE B standard bulbs (not included). To avoid the risk of

E

F

G

F

C

J

H

I

A

B

C

D

assembly instructions

A

B

G

I

H

C

D

K

E

grounding screw 1x

canopy screw 4x

mounting screw 2x

wire cap 3x

wrench 1x

To Assemble:

1. SHUT OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER.

2. Carefully unpack all fixture parts and hardware and lay out on a clear workspace.

3. Carefully inspect the fixture wires. The NEUTRAL FIXTURE WIRE is white. The HOT FIXTURE

WIRE is black. The bare wire is the GROUND WIRE.

4. Attach the GROUND WIRE from the fixture to the GROUND JUNCTION BOX WIRE from the outlet (usually

green or bare wire). Fasten each together with a plastic wire connector (A) and wrap the connection with

electrical tape. Be sure that no wire strands are exposed. If your outlet box DOES NOT have a GROUND WIRE,

be sure to insert the green ground screw (B) into the mounting plate (J) as shown, and wrap the fixture's

bare ground wire around the ground screw.

PROPERLY GROUNDED.

5. Connect the NEUTRAL FIXTURE WIRE to the NEUTRAL JUNCTION BOX WIRE ( white). Fasten each together

with a plastic wire connector (A) and wrap the connection with electrical tape. Be sure no wire strands are

exposed.

9157959 - 01/07

IT IS IMPERATIVE THAT THE OUTLET BOX IN YOUR HOME BE

page 1 of 2

6. Connect the HOT FIXTURE WIRE to the HOT JUNCTION BOX WIRE (black). Fasten each together with a

plastic wire connector (A) and wrap the connection with electrical tape. Be sure no wire strands are exposed. DO

NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS OR SAFETY WILL BE COMPROMISED.

7. Gently tuck the wire connections neatly into the ceiling junction box.

8. Attach the mounting plate (J) to the ceiling outlet box using the enclosed mounting screws (D). Tighten screws

with a screwdriver.

9. Pull canopy (I) up over the mounting plate (J), align the hole in the mounting plate with the hole in the canopy.

10. Insert the canopy screw (C) tighten with a screwdriver.

11. Unscrew socket ring (F )from the socket.

12. Place glass shade (H) on metal plate (K).

13. Place metal tube (G) onto the socket .

14. Screw on the socket rings (F) and tighten with wrench (E).

Completing the Assembly:

1. Insert (2) 60-watt Type B bulbs (not included) into the socket . DO NOT EXCEED SPECIFIED WATTAGE.

2. Restore power to junction box and test fixture.

Care Instructions:

• Wipe clean using a soft, dry cloth or static duster.

• Always avoid the use of harsh chemicals and abrasives to clean fixture as they may damage the finish.

9157959 - 01/07

page 2 of 2