West Elm Coconut Strips Pendant Assembly Instruction
coconut strips pendant
Important Safety Instructions:
·Joist mounting is recommended. Use proper hardware for your ceiling type. When in doubt consult your local hardware
store. For your safety, it is strongly recommended that two people hang the lamp.
·Light bulb should be centered inside the pendant shade. Making sure it does not touch the shade.
·These instructions are provided for your safety. It is important that they are read carefully and completely before
assembling xture.
·This xture has been rated for up to (1) 60-watt maximum TYPE A standard light bulb (not included). To avoid the risk of
re, do not exceed the recommended wattage.
Warning:
·To reduce the risk of re, electrical shock or personal injury, always turn o lamp and allow it to cool prior to replacing light
bulb.
·Do not touch light bulb when xture is turned on.
·Keep ammable materials away from light bulb.
·THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODES BY A PERSON FAMILIAR
WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
·Do not install on a radiant-heating ceiling.
assembly instructions
Pre-assembly:
·Remove all parts and hardware from box along with any plastic protective
packaging.
·Do not discard any contents until after assembly is complete to avoid accidentally
discarding small parts or hardware.
·For your safety and convenience, assembly by two people is recommended.
·In order to use conversion kit, you must already have purchased a West Elm 3 wire
cordset with plug shown below:
J
A
wire nut connector 3x
C
canopy screw 2x
B
ground screw 1x
D
mounting screw 2x
ceiling junction box
A
E
D
B
C
L
K
I
F
Hardware Included:
• Wire Connector (A)
• Ground Screw (B)
• Canopy Screw (C)
• Mounting Screw (D)
Tools needed:
1772060/1742857
Parts Enclosed:
• Mounting Plate (E)
• Cord Screw (I)
• Canopy (L)
Parts Enclosed
w/3-Wire Cordset :
• Socket (F)
• Socket Ring (G)
• Shade (H)
• Cable Stop (J)
• Cable Screw (K)
H
G
page 1 of 3
coconut strips pendant
Assembly:
1. SHUT OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER.
2. Carefully unpack all xture parts and hardware and lay out on a clear workspace.
3. Unscrew the plastic cord screw (I) from the canopy (L) using a small ate blade screwdriver.
4. Cut o the plug form the power cord and insert the wire into the canopy. Make sure to cut the cord and ground
connector so that they are at least 6 inches long within the outlet box.
5. Unscrew the cable screw (K) from the cable stop (J) and take the steel cable out.
STEP 5
J
K
6. Insert the steel cable through the canopy.
STEP 6
assembly instructions
7. Insert the steel cable into the cable stop and tighten the cable screws with a small screwdriver.
STEP 7
8. Tighten the plastic cord screw screw with a screwdriver.
9. Carefully inspect the lamp’s xture wires. The NEUTRAL FIXTURE WIRE is white. The HOT FIXTURE WIRE is clear. The green
wire is the GROUND WIRE.
10. Attach the GROUND WIRE from the xture to the GROUND JUNCTION BOX WIRE from the outlet (usually green or bare
wire). Fasten each together with a plastic wire nut connector (A) and wrap the connection with electrical tape. Be sure that
no wire strands are exposed. If your junction box DOES NOT have a GROUND WIRE, be sure to insert the green ground screw
(B ) into the mounting plate (E), marked as “GND”, and wrap the xture's bare ground wire around the ground screw. IT IS
IMPERATIVE THAT THE JUNCTION BOX IN YOUR HOME BE PROPERLY GROUNDED.
1772060/1742857
page 2 of 3
Loading...