I2t capacity for fusing tp=10ms, Vrm≤10V, (note 5)
Operating temperature range-55 to +175°C
Storage temperature range-55 to +200°C
=25°C, (note 4)5047A
sink
=55°C, (note 2)3270A
sink
=85°C, (note 2)2693A
sink
=85°C, (note 3)1638A
sink
=25°C, (note 2)5949A
sink
, (note 5)30.4kA
RRM
, (note 5)4.62×10
RRM
Data Sheet Issue:- 5
MAXIMUM
LIMITS
MAXIMUM
LIMITS
33.5kA
6
5.61×10
6
UNITS
UNITS
A2s
A2s
Notes:-
1) De-rating factor of 0.13% per °C is applicable for T
2) Double side cooled, single phase; 50Hz, 180° half-sinewave.
3) Single side cooled, single phase; 50Hz, 180° half-sinewave.
4) Double side cooled.
5) Half-sinewave, 175°C T
Data Sheet. Types W3270N#080 to W3270N#220 Issue 5Page 1 of9April, 2008
initial.
j
below 25°C.
j
WESTCODE
WESTCODE An IXYS Company Rectifier Diode Types W3270N#080 to W3270N#220
WESTCODEWESTCODE
Characteristics
PARAMETERMIN.TYP.MAX. TEST CONDITIONS (Note 1)UNITS
V
V
V
r
I
I
Q
Q
I
t
R
FM
FM
T0
T
RRM
RRM
rr
ra
rr
rr
thJK
Maximum peak forward voltage--1.47ITM=6400AV
Maximum peak forward voltage--1.76ITM=9800AV
Threshold voltage--0.826V
Slope resistance--0.104
Peak reverse current--50Rated V
Peak reverse current--50Rated V
RRM
, Tj=25°CmA
RRM
mΩ
mA
Recovered charge-2400-µC
Recovered charge, 50% Chord-19002350µC
Reverse recovery current-150-A
Reverse recovery time-25-
Thermal resistance, junction to heatsink
--0.022 Double side cooledK/W
I
=1000A, tp=1000µs, di/dt=10A/µs,
TM
V
=50V
r
µs
--0.044 Single side cooledK/W
FMounting force19-26kN
W
Weight-510-g
t
Notes:-
1) Unless otherwise indicated T
=175°C.
j
2) For other clamp forces, please consult factory.
Notes on rupture rated packages.
This product is available with a non-rupture rated package.
For additional details on these products, please consult factory.
Data Sheet. Types W3270N#080 to W3270N#220 Issue 5Page 2 of9April, 2008
WESTCODE
WESTCODE An IXYS Company Rectifier Diode Types W3270N#080 to W3270N#220
This report is applicable to other voltage grades when supply has been agreed by Sales/Production.
3.0 De-rating Factor
A blocking voltage de-rating factor of 0.13%/°C is applicable to this device for Tj below 25°C.
4.0 Snubber Components
When selecting snubber components, care must be taken not to use excessively large values of snubber
capacitor or excessively small values of snubber resistor. Such excessive component values may lead to
device damage due to the large resultant values of snubber discharge current. If required, please consult
the factory for assistance.
DRM VDSM VRRM
V
V
RSM
V
V
V
D
DC V
R
5.0 Computer Modelling Parameters
5.1 Device Dissipation Calculations
2
I
=
AV
Where VT0=0.826V, rT=0.104mΩ,
R
= Supplementary thermal impedance, see table below and