Westcode Semiconductors N2543ZC240, N2543ZC300 Data Sheet
Date:- 19 Sep, 2003
WESTCODE
An
Absolute Maximum Ratings
V
DRM
V
DSM
V
RRM
V
RSM
I
T(AVM)
I
T(AVM)
I
T(AVM)
I
T(RMS)
I
T(d.c.)
I
TSM
I
TSM2
I2tI
I2t
(di/dt)
V
RGM
P
G(AV)
P
GM
T
HS
T
stg
IXYS
Company
Phase Control Thyristor
Types N2543ZC240 to N2543ZC300
Old Type No.: N880CH24-30
VOLTAGE RATINGS
Repetitive peak off-state voltage, (note 1) 2400-3000 V
Non-repetitive peak off-state voltage, (note 1) 2400-3000 V
Repetitive peak reverse voltage, (note 1) 2400-3000 V
Non-repetitive peak reverse voltage, (note 1) 2500-3100 V
OTHER RATINGS
Maximum average on-state current, T
Maximum average on-state current. T
Maximum average on-state current. T
Nominal RMS on-state current, T
D.C. on-state current, T
Peak non-repetitive surge tp=10ms, Vrm=0.6V
Peak non-repetitive surge tp=10ms, V
2
t capacity for fusing tp=10ms, Vrm=0.6V
2
I
t capacity for fusing tp=10ms, V
Critical rate of rise of on-state current (repetitive), (Note 6) 150 A/µs
cr
Critical rate of rise of on-state current (non-repetitive), (Note 6) 300 A/µs
Peak reverse gate voltage 5 V
Mean forward gate power 4 W
Peak forward gate power 30 W
Operating temperature range -40 to +125 °C
Storage temperature range -40 to +150 °C
=25°C, (note 4)
sink
rm
=55°C, (note 2)
sink
=85°C, (note 2)
sink
=85°C, (note 3)
sink
=25°C, (note 2)
sink
≤
10V, (note 5)
rm
RRM
≤
10V, (note 5)
, (note 5) 32 kA
RRM
, (note 5) 5.12×10
Data Sheet Issue:- 3
MAXIMUM
LIMITS
MAXIMUM
LIMITS
2543 A
1811 A
1160 A
4922 A
4509 A
39 kA
6
7.61×10
6
UNITS
UNITS
A2s
A2s
Notes: -
1)
De-rating factor of 0.13% per °C is applicable for Tj below 25°C.
2)
Double side cooled, single phase; 50Hz, 180° half-sinewave.
3)
Single side cooled, single phase; 50Hz, 180° half-sinewave.
4)
Double side cooled.
5)
Half-sinewave, 125°C Tj initial.
6)
VD=67% V
Data Sheet. Types N2543ZC240 to N2543ZC300 Issue 3. Page 1 of 11 September, 2003
, ITM=1000A, IFG=2A, t
DRM
≤
0.5µs, T
r
case
=125°C.
WESTCODE
An IXYS Company
Characteristics
Phase Control Thyristor Types N2543ZC240 to N2543ZC300
PARAMETER MIN. TYP. MAX. TEST CONDITIONS
V
TM
V
T0
r
T
(dv/dt)crCritical rate of rise of off-state voltage 1000 - - VD=80% V
I
DRM
I
RRM
V
GT
I
GT
V
GD
I
H
t
gd
t
gt
Q
rr
Q
ra
I
rm
t
rr
t
q
R
thJK
Maximum peak on-state voltage - - 1.6 ITM=3000A V
Threshold voltage - - 0.78 V
Slope resistance - - 0.274
Peak off-state current - - 200 Rated V
Peak reverse current - - 200 Rated V
Gate trigger voltage - - 3.0 V
T
Gate trigger current - - 300
Non-trigger gate voltage, (Note 7) - - 0.25 Rated V
DRM
RRM
=25°C, VD=10V, IT=3A
j
DRM
Holding current - - 1000 Tj=25°C mA
Gate controlled turn-on delay time - 0.5 1.0
Turn-on time - 1.0 2.0
=67%V
V
D
I
=2A, tr=0.5µs, Tj=25°C
FG
Recovered Charge - 7750 - µC
Recovered Charge, 50% chord - 3900 5400 µC
Reverse recovery current - 190 - A
I
=4000A, tp=1000µs, di/dt=10A/µs,
TM
V
=50V
r
Reverse recovery time, 50% chord - 40.0 -
ITM=4000A, tp=1000µs, di/dt=10A/µs,
V
=50V, Vdr=80%V
r
ITM=4000A, tp=1000µs, di/dt=10A/µs,
V
=50V, Vdr=80%V
r
Turn-off time
Thermal resistance, junction to heatsink
- 350 -
- 400 -
--0.011 Double side cooled K/W
--
0.022 Single side cooled K/W
(Note 1)
, linear ramp, Gate O/C
DRM
, ITM=2000A, di/dt=10A/µs,
DRM
, dVdr/dt=20V/µs
DRM
, dVdr/dt=200V/µs
DRM
UNITS
m
V/µs
mA
mA
mA
V
µs
µs
µs
F Mounting force 27 - 47 kN
W
t
Weight - 1.7 - kg
Ω
Notes: -
Unless otherwise indicated Tj=125°C.
1)
Data Sheet. Types N2543ZC240 to N2543ZC300 Issue 3. Page 2 of 11 September, 2003
WESTCODE
An IXYS Company
Notes on Ratings and Characteristics
1.0 Voltage Grade Table
Phase Control Thyristor Types N2543ZC240 to N2543ZC300
Voltage Grade
V
DRM VDSM VRRM
V
V
RSM
V
V
V
D
DC V
R
24 2400 2500 1450
26 2600 2700 1550
28 2800 2900 1650
30 3000 3100 1750
2.0 Extension of Voltage Grades
This report is applicable to other voltage grades when supply has been agreed by Sales/Production.
3.0 De-rating Factor
A blocking voltage de-rating factor of 0.13%/°C is applicable to this device for Tj below 25°C.
4.0 Repetitive dv/dt
Standard dv/dt is 1000V/µs.
5.0 Snubber Components
When selecting snubber components, care must be taken not to use excessively large values of snubber
capacitor or excessively small values of snubber resistor. Such excessive component values may lead to
device damage due to the large resultant values of snubber discharge current. If required, please consult
the factory for assistance.
6.0 Rate of rise of on-state current
The maximum un-primed rate of rise of on-state current must not exceed 300A/µs at any time during turnon on a non-repetitive basis. For repetitive performance, the on-state rate of rise of current must not
exceed 150A/µs at any time during turn-on. Note that these values of rate of rise of current apply to the
total device current including that from any local snubber network.
7.0 Gate Drive
The nominal requirement for a typical gate drive is illustrated below. An open circuit voltage of at least 30V
is assumed. This gate drive must be applied when using the full di/dt capability of the device.
I
GM
4A/µs
I
G
t
p1
The magnitude of IGM should be between five and ten times IGT, which is shown on page 2. Its duration
) should be 20µs or sufficient to allow the anode current to reach ten times IL, whichever is greater.
(t
p1
Otherwise, an increase in pulse current could be needed to supply the necessary charge to trigger. The
‘back-porch’ current I
magnitude in the order of 1.5 times I
should remain flowing for the same duration as the anode current and have a
G
.
GT
Data Sheet. Types N2543ZC240 to N2543ZC300 Issue 3. Page 3 of 11 September, 2003
WESTCODE
8.0 Computer Modelling Parameters
I
AV
Where VT0=0.78V, rT=0.274m
R
= Supplementary thermal impedance, see table below and
th
ff
= Form factor, see table below.
Square wave Double Side Cooled 0.0124 0.0122 0.0121 0.0119 0.0117 0.0113 0.011
Square wave Single Side Cooled 0.0249 0.0248 0.0247 0.0246 0.0244 0.0241 0.022
Sine wave Double Side Cooled 0.0168 0.0140 0.0131 0.0118 0.0112
Sine wave Single Side Cooled 0.0249 0.0247 0.0246 0.0244 0.0241
An IXYS Company
8.1 Device Dissipation Calculations
2
4
=
Conduction Angle 30° 60° 90° 120° 180° 270° d.c.
00
⋅⋅
2
rff
Ω,
⋅⋅⋅++−
WrffVV
AVs
and:
s
Supplementary Thermal Impedance
Phase Control Thyristor Types N2543ZC240 to N2543ZC300
∆
T
AV
=
R
th
max
−=∆
TTT
Hsj
W
Form Factors
Conduction Angle 30° 60° 90° 120° 180° 270° d.c.
Square wave 3.464 2.449 2 1.732 1.414 1.149 1
Sine wave 3.98 2.778 2.22 1.879 1.57
8.2 Calculating VT using ABCD Coefficients
The on-state characteristic I
(i) the well established V
(ii) a set of constants A, B, C, D, forming the coefficients of the representative equation for V
terms of I
The constants, derived by curve fitting software, are given below for both hot and cold characteristics. The
resulting values for V
that plotted.
given below:
T
T
vs. VT, on page 6 is represented in two ways;
T
and rs tangent used for rating purposes and
0
in
T
()
ln
agree with the true device characteristic over a current range, which is limited to
125°C Coefficients
A 1.307753
B -0.1906143
C 4.623129×10
D 0.03065344
-5
⋅+⋅+⋅+=
IDICIBAV
TTTT
Data Sheet. Types N2543ZC240 to N2543ZC300 Issue 3. Page 4 of 11 September, 2003
Loading...