The vibration unit uses two ÒDÓ Batteries (not included). To
install batteries, pull the pillow case aside on the end of the
pillow with the switch. Gently pull the vibration unit out of the
slot in the pillow. Make sure you donÕt disconnect the wires
between the vibration unit and the on/off switch.
Install two ÒDÓ batteries into the battery holder in the position
indicated on the diagram inside the holder. Put the vibration
unit back into the slot in the pillow and pull the pillow case
back into place.
The vibration unit is turned on and off by flipping the switch
on one side of the pillow.
CAUTION: The vibration massage should not be used
more than 20 minutes per session. Continuous usage
could cause slight bruises.
CAUTION: Do not use magnet therapy if you are pregnant or wearing a pacemaker or any other electrical
implants. Magnets are not being sold as medical
devices.
CAUTION: The pillow case can be removed and washed.
Remove the vibration unit before removing the pillow
case. Do not wash the pillow or the vibration unit.
Operating the Vibration Unit
The pillow case can be removed
for cleaning. To do this, pull the pillow case aside to expose the vibration unit. Pull the vibration unit out
of the slot in the pillow. Remove
the pillow case from the pillow.
The switch is held in place by two
white support plates. The inside
plate is secured with two tabs, one
on each side of the switch casing.
Press these tabs together with pliers and remove the inside
support plate. Pull the switch and the outside support plate
through the slot in the pillow case.
To re-install the pillow case, start by inserting the switch and
the outside support plate through the slot in the pillow case
from the inside. Press the inside support plate over the two
tabs on the switch casing. Push the pillow into the pillow
case. Insert the vibration unit into the slot in the pillow and
pull the pillow case back into place. Do not wash the vibra-
tion unit, the switch or the pillow.
Removing the Pillow Case
Installing or Replacing the Batteries
QUESTIONS?
As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, we will
guarantee complete satisfaction through direct assistance
from our factory.
Please call our CUSTOMER HOT LINE:
1-800-999-3756
Mon.ÐFri., 6 a.m.Ð6 p.m. MST
Ta b
Switch
Ta b
Support Plate
The vibration unit uses two ÒDÓ Batteries (not included). To
install batteries, pull the pillow case aside on the end of the
pillow with the switch. Gently pull the vibration unit out of the
slot in the pillow. Make sure you donÕt disconnect the wires
between the vibration unit and the on/off switch.
Install two ÒDÓ batteries into the battery holder in the position
indicated on the diagram inside the holder. Put the vibration
unit back into the slot in the pillow and pull the pillow case
back into place.
The vibration unit is turned on and off by flipping the switch
on one side of the pillow.
CAUTION: The vibration massage should not be used
more than 20 minutes per session. Continuous usage
could cause slight bruises.
CAUTION: Do not use magnet therapy if you are pregnant or wearing a pacemaker or any other electrical
implants. Magnets are not being sold as medical
devices.
CAUTION: The pillow case can be removed and washed.
Remove the vibration unit before removing the pillow
case. Do not wash the pillow or the vibration unit.
Operating the Vibration Unit
The pillow case can be removed
for cleaning. To do this, pull the pillow case aside to expose the vibration unit. Pull the vibration unit out
of the slot in the pillow. Remove
the pillow case from the pillow.
The switch is held in place by two
white support plates. The inside
plate is secured with two tabs, one
on each side of the switch casing.
Press these tabs together with pliers and remove the inside
support plate. Pull the switch and the outside support plate
through the slot in the pillow case.
To re-install the pillow case, start by inserting the switch and
the outside support plate through the slot in the pillow case
from the inside. Press the inside support plate over the two
tabs on the switch casing. Push the pillow into the pillow
case. Insert the vibration unit into the slot in the pillow and
pull the pillow case back into place. Do not wash the vibra-
tion unit, the switch or the pillow.
Removing the Pillow Case
Installing or Replacing the Batteries
QUESTIONS?
As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, we will
guarantee complete satisfaction through direct assistance
from our factory.
Please call our CUSTOMER HOT LINE:
1-800-999-3756
Mon.ÐFri., 6 a.m.Ð6 p.m. MST
Ta b
Switch
Ta b
Support Plate