Weslo WCTL29310.0 User Manual

Model No. WCTL29310.0 Serial No.

Write the serial number in the space above for future reference.

Serial Number

Decal

QUESTIONS?

If you have questions, or if parts are damaged or missing, PLEASE

CONTACT OUR CUSTOMER SERVICE DEPARTMENT DIRECTLY.

CALL TOLL-FREE:

1-888-936-4266

Mon.–Fri., 7:30 until 16:30 EST (excluding holidays)

USER'S MANUAL

OR E-MAIL US: customerservice@iconcanada.ca

CAUTION

Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference.

www.weslo.com

TABLE OF CONTENTS

WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

MPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

WARNING DECAL PLACEMENT

This drawing shows the location(s) of the warning decal(s). If a decal is missing or illegible,

call the telephone number on the front cover of this manual and request a free replacement decal. Apply the decal in the location shown. Note: The decal(s) may not be shown at

actual size.

WESLO is a registered trademark of ICON IP, Inc.

IMPORTANT PRECAUTIONS

WARNING: To reduce the risk of serious injury, read all important precautions and in-

structions in this manual and all warnings on your treadmill before using your treadmill. ICON as-

umes no responsibility for personal injury or property damage sustained by or through the use of

s this product.

1. Before beginning this or any exercise program, consult your physician. This is especially important for persons over age 35 or persons with pre-existing health problems.

2. It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of all warnings and precautions.

3. Use the treadmill only as described.

4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a garage or covered patio, or near water.

5. Place the treadmill on a level surface, with at least 8 ft. (2.4 m) of clearance behind it and 2 ft. (0.6 m) on each side. Do not place the treadmill on any surface that blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.

6. Do not operate the treadmill where aerosol products are used or where oxygen is being administered.

7. Keep children under age 12 and pets away from the treadmill at all times.

8. The treadmill should not be used by persons weighing more than 250 lbs. (113 kg).

9. Never allow more than one person on the treadmill at a time.

10. Wear appropriate exercise clothes when using the treadmill. Do not wear loose clothes that could become caught in the treadmill. Athletic support clothes are recommended for both men and women. Always wear athletic

shoes; never use the treadmill with bare feet, wearing only stockings, or in sandals.

into a grounded circuit capable of carrying 15 or more amps. No other appliance should be on the same circuit. Do not use an extension cord.

12. Use only a single-outlet surge suppressor that meets all of the specifications described on page 11. To purchase a surge suppressor call the telephone number on the front cover of this manual.

13. Failure to use a properly functioning surge suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may slow, accelerate, or stop unexpectedly, which may result in a fall and serious injury.

14. Keep the power cord and the surge suppressor away from heated surfaces.

15. Never move the walking belt while the power is turned off. Do not operate the treadmill if the power cord or plug is damaged, or if the treadmill is not working properly. (See TROUBLESHOOTING on page 18 if the treadmill is not working properly.)

16. Read, understand, and test the emergency stop procedure before using the treadmill (see HOW TO TURN ON THE POWER on page 13).

17. Never start the treadmill while you are standing on the walking belt. Always hold the handrails or upper body arms while using the treadmill.

18. The pulse sensor is not a medical device. Various factors, including your movement, may affect the accuracy of heart rate readings. The pulse sensor is intended only as an exercise aid in determining heart rate trends in general.

11. When connecting the power cord (see page 11), plug the power cord into a surge suppressor (not included) and plug the surge suppressor

19. The treadmill is capable of high speeds. Adjust the speed in small increments to avoid sudden jumps in speed.

20. Never leave the treadmill unattended while it is running. Always remove the key, unplug

he power cord, and press the power switch

t into the off position when the treadmill is not in use. (See the drawing on page 5 for the location of the power switch.)

21. Do not attempt to raise, lower, or move the treadmill until it is properly assembled. (See ASSEMBLY on page 6 and HOW TO FOLD AND MOVE THE TREADMILL on page 17.) You must be able to safely lift 45 lbs. (20 kg) to raise, lower, or move the treadmill.

25. Never drop or insert any object into any opening on the treadmill.

DANGER: Always unplug the power

26. cord immediately after use, before cleaning

he treadmill, and before performing the main-

t tenance and adjustment procedures described in this manual. Never remove the motor hood unless instructed to do so by an authorized service representative. Servicing other than the procedures in this manual should be performed by an authorized service representative only.

22. When folding or moving the treadmill, make sure that the storage latch is holding the frame securely in the storage position.

23. Do not change the incline of the treadmill by placing objects under the treadmill.

24. Inspect and properly tighten all parts of the treadmill regularly.

SAVE THESE INSTRUCTIONS

27. This treadmill is intended for in-home use only. Do not use this treadmill in any commercial, rental, or institutional setting.

28. Over exercising may result in serious injury or death. If you feel faint or if you experience pain while exercising, stop immediately and cool down.

BEFORE YOU BEGIN

Thank you for selecting the new WESLO CROSSWALK 5.0T treadmill. The CROSSWALK 5.0T

readmill offers a selection of features designed to

t make your workouts at home more effective. And

hen youʼre not exercising, the unique treadmill can

w be folded up, requiring less than half the floor space of other treadmills.

For your benefit, read this manual carefully before using the treadmill. If you have questions after read-

Upper Body Arm

Handrail

ing this manual, please see the front cover of this manual. To help us assist you, note the product model

umber and serial number before contacting us. The

n model number and the location of the serial number

ecal are shown on the front cover of this manual.

Before reading further, please review the drawing below and familiarize yourself with the labeled parts.

Console

Key/Clip

Storage Latch

Walking Belt

Foot Rail

Idler Roller Adjustment Bolts

Hood

Power Switch

Power Cord

Wheel

Platform Cushion

Incline Leg

M10 Star

Washer (9)–4

M8 Star

Washer (5)–6

M5 x 16mm

Screw (85)–2

M5 Star

Washer (7)–2

M4.2 x 19mm Screw (10)–4

1/4" Flat Washer

(101)–4

1/4" x 3 1/2" Bolt (103)–4

M10 x 58mm Bolt (2)–4

M4.2 x 18mm Screw (58)–2

M10 Nut (73)–4

M8 x 15mm

Bolt (8)–6

ASSEMBLY

ssembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not

A dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking

belt is coated with high-performance lubricant. During shipping, some lubricant may be transferred to the top of the walking belt or the shipping carton. This is normal and does not affect treadmill performance. If there is lubri-

ant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included hex keys and your own Phillips screwdriver , adjustable wrench , and needlenose pliers .

Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses is the quantity needed for assembly. Note: Some small parts may have been preassembled. To avoid dam-

aging parts, do not use power tools for assembly. Extra hardware may be included.

1. With the help of a second person, carefully tip the treadmill onto its side. Unfold the Frame (51) away from the Uprights (53, 54).

Orient the Base (52) as shown. Attach the Base

o the Left Upright (53) and the Right Upright

t (54) with four M10 x 58mm Bolts (2) and four M10 Nuts (73). Start all four Nuts, and then tighten each of them.

With the help of a second person, carefully tip the treadmill so that the Base (52) is flat on the floor.

2. Set the console assembly face down on a soft surface to avoid scratching it.

Identify the Right Handrail (33), which has a large hole in the location shown. Hold the Right Handrail near the console assembly.

Next, insert the console wire into the large hole in the side of the Right Handrail (33). Using needlenose pliers, carefully grasp the connector and pull the console wire out of the hole near the bracket on the Right Handrail.

Console Wire

Bracket

Console

Assembly

Connector

Large

Hole

3. Set the Right Handrail (33) on the console as-

embly. Make sure that the console wire is

s not pinched. Remove the tie from the bracket on the Right Handrail. If necessary, press the Cage Nuts (110) back into place.

Start an M5 x 16mm Screw (85) with an M5 Star Washer (7) into the Right Handrail, and then start two M4.2 x 19mm Screws (10) into the Right Handrail. Tighten the M5 x 16mm Screw

and then tighten the two M4.2 x 19mm Screws; do not overtighten the Screws.

Attach the Left Handrail (not shown) to the console assembly in the same way. Note:

There is no wire on the left side.

onsole Wire

Bracket

Console

Assembly

110

ire Tie

4. With the help of a second person, hold the console assembly near the Right Upright (54).

Connect the Wire Harness (39) to the console wire. See the inset drawing. The connectors

should slide together easily and snap into place. If they do not, turn one connector and try again. IF YOU DO NOT CONNECT THE CONNECTORS PROPERLY, THE CONSOLE MAY BECOME DAMAGED WHEN YOU TURN ON THE POWER. If there is a wire tie on the Wire

Harness, remove the wire tie. Insert the connectors and the excess wire downward into the Right Upright (54).

5. Set the console assembly on the Uprights (53,

54). Make sure that no wires are pinched. Start four M8 x 15mm Bolts (8) with four M8 Star Washers (5) into the Uprights as shown. Do not

tighten the Bolts yet.

Console

Assembly

Console

Wire

Console

Wire

Console Assembly

6. Start an M8 x 15mm Bolt (8) with an M8 Star

asher (5) into each Upright (53, 54). Then,

firmly tighten all six M8 x 15mm Bolts (8).

7. Attach the Latch Housing (48) to the Left Upright (53) with two M4.2 x 18mm Screws (58); start

both Screws, and then tighten both of them.

+ 19 hidden pages