Model No. WATL16105.0
erial No.
S
Serial Number Decal
QUESTIONS?
If you have questions, or if any
parts are missing or damaged,
PLEASE CONTACT OUR CUSTOMER SERVICE DEPARTMENT
DIRECTLY.
Call toll-free:
800-830-7240
E-mail:
service@goodfamily.cc
USER'S MANUAL
Goodfamily’s Web site:
www.goodfamily.cc
ICON’s Web site:
www.iconfitness.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
Goodfamily is an authorized dealer of this treadmill in the territory of mainland China. This treadmill is designed and man
ufactured by ICON
Health
& Fitness, Inc.
-
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: A PART IDENTIFICATION CHART, an EXPLODED DRAWING, and a PART LIST are found at the end of
this manual.
WESLO is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
ollowing important precautions and information before operating the treadmill.
f
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
2. Use the treadmill only as described.
3. Place the treadmill on a level surface, with at
least 2.5 m (8 ft.) of clearance behind it and
0.5 m (2 ft.) on each side. Do not place the
treadmill on any surface that blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
7. The treadmill should not be used by persons
weighing more than 115 kg (250 lbs.).
8. Never allow more than one person on the
treadmill at a time.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women.
shoes; never use the treadmill with bare feet,
wearing only stockings, or in sandals.
10.
When connecting the power cord (see page 9),
plug the power cord into an earthed circuit. No
other appliance should be on the same circuit.
When replacing the fuse, an ASTA approved
BS1362 type should be fitted to the fuse carrier.
A 13 amp fuse should be used.
11. If an extension cord is needed, use only a 3conductor, 1mm
longer than 1.5 m (5 ft.).
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
12. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
13. Keep the power cord and the surge suppressor away from heated surfaces.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See MAINTENANCE AND TROUBLESHOOTING on page
13 if the treadmill is not working properly.)
15. Read, understand, and test the emergency
stop procedure before using the treadmill (see
OPERATION AND ADJUSTMENT on page 9).
16. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
17. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
18. Never leave the treadmill unattended while it is
running. Always remove the key and unplug
the power cord when the treadmill is not in use.
19. Do not attempt to raise, lower, or move the
Always wear athletic
2
(14-gauge) cord that is no
treadmill until it is properly assembled. (See
ASSEMBLY on page 6 and HOW TO FOLD
AND MOVE THE TREADMILL on page 12.)
You must be able to safely lift 20 kg (45 lbs.)
to raise, lower, or move the treadmill.
20. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
Do not change the incline of the treadmill by
21.
placing objects under the treadmill.
3
2. Inspect and properly tighten all parts of the
2
treadmill regularly.
23. Never drop or insert any object into any
pening.
o
24. DANGER: Always unplug the power
ord immediately after use, before cleaning
c
the treadmill, and before performing the maintenance and adjustment procedures de-
cribed in this manual. Never remove the
s
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
25. This treadmill is intended for in-home use
only. Do not use this treadmill in any commercial, rental, or institutional setting.
WARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown at the right have been placed on the
treadmill. If a decal is missing or illegible, call the telephone number on the front cover of this manual and
order a free replacement decal. Apply the decal in the location shown. Note: The decals are not shown at actual
size.
4
BEFORE YOU BEGIN
Thank you for selecting the WESLO®A-40 treadmill.
The A-40 treadmill combines advanced technology
with innovative design to let you enjoy an excellent
form of cardiovascular exercise in the convenience and
rivacy of your home. And when you’re not exercising,
p
the unique A-40 treadmill can be folded up, requiring
less than half the floor space of other treadmills.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
Water Bottle Holder
(No bottle is included)
Handrail
Storage Latch
ing this manual, please see the front cover of this manual. To help us assist you, note the product model
number and serial number before calling. The model
number of the treadmill is WATL16105.0. The serial
umber can be found on a decal attached to the tread-
n
mill (see the front cover of this manual for the location).
Before reading further, please familiarise yourself with
the parts that are labelled in the drawing below.
Console
Key/Clip
LEFT SIDE
Walking Belt
Foot Rail
Rear Roller
Adjustment Bolts
RIGHT SIDE
Hood
Circuit Breaker
Wheel
Incline Leg
5
ASSEMBLY
ssembly requires two persons.Set the treadmill in a cleared area and remove all packing materials. Do not
A
remove the long wire inside of the right handrail yet. In addition, do not dispose of the packing materials
until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance
lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the
shipping carton. This does not affect treadmill performance. If there is lubricant on top of the walking belt, simply
wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex key and your own phillips screwdriver , adjustable
spanner , and wire cutters .
Note: To identify small parts used during assembly, see the PART IDENTIFICATION CHART in the center of
this manual. Some parts may be preassembled.
1. Attach the six Base Pads (19) to the bottom of the Base
(71) with six Base Pad Screws (42).
2. Have a second person hold the Base (71) in the position
shown.
Identify the Right Handrail (6), which has a large hole near
the lower end.
the position shown.
Base (71) with two Handrail Bolts (12) and two Nuts (17).
Do not tighten the Handrail Bolts yet.
Hold the Right Handrail so the bend is in
Attach the Right Handrail to the
1
71
42
19
42
42
19
19
2
7
42
19
42
19
Bend
Attach the Left Handrail (7) to the Base (71) in the same
way.
6
17
71
6
12
Large
Hole
12
3. With the help of a second person, raise the Handrails
(6, 7) so the Base (71) is flat on the floor.
Attach the Wheels (15) to the outer sides of the Base
71) with two Wheel Bolts (14) and two Nuts (17). D
(
overtighten the Nuts; the Wheels should turn freely.
Position the treadmill Frame (55) between the Handrails
(6, 7) as shown. See the inset drawing. Locate the wire in
the lower end of the Right Handrail (6). Using the included plastic tie, secure the wire to the Wire Harness
(22). Next, pull the opposite end of the wire until the Wire
Harness is routed through the Right Handrail. Then, disconnect and discard the wire.
o not
3
7
55
22
Tie
22
6
17
15
14
71
Wire
6
4. Have a second person lift and hold the front end of the
Frame (55). Hold a Frame Spacer (13) between the Right
Handrail (6) and the Frame. Attach the Right Handrail to
the Frame with a Frame Bolt (10), a Handrail Washer
(30), and a Handrail Star Washer (60).
Repeat this step on the left side of the treadmill.
5. Hold the Console Base (1) near the Right Handrail (6).
Touch the Right Handrail to discharge any static.
Insert the end of the Wire Harness (22) through the three
looped plastic ties. Next, press the end of the Wire
Harness into the connector on the back of the Console
Base (1) in the location shown. The end of the Wire
Harness should slide easily into the connector and
snap into place. If it does not, turn the end of the Wire
Harness and then insert it. IF THE CONNECTORS ARE
NOT CONNECTED PROPERLY, THE CONSOLE MAY
BE DAMAGED WHEN THE POWER IS TURNED ON.
4
6
13
30
10
60
55
5
1
Connector
22
Plastic
6
Ties
22
7
6. Set the Console (1) on the Right Handrail (6) and the Left
Handrail (not shown). Start four Console Screws (70)
only two are shown) into the Console. A
(
started all four Console Screws, tighten them.
Insert the excess Wire Harness (22) down into the Right
Handrail (6). Tighten the three plastic ties around the Wire
Harness, and then cut off the ends of the plastic ties.
fter you have
6
70
1
22
Plastic
Ties
6
7. Attach the Console Back (4) to the Console (1) with four
16mm Screws (87). Note that there is a slot in the side of
the Console Back for the Wire Harness (22).
that no wires are pinched.
8. Carefully lower the Handrails (6, 7) to the floor. Center the
Frame (55) between the Handrails, and tighten the four
Handrail Bolts (12). Then, raise the Handrails to the vertical position.
Make sure
7
8
87
1
Slot
55
87
4
87
12
See the inset drawing. Attach the Latch Assembly (41) to
the Left Handrail (7) with two 16mm Screws (87).
sure that the Latch Assembly is oriented as shown.
See HOW TO CHANGE THE INCLINE OF THE TREAD
MILL on page 11. Adjust the Incline Legs to the desired
height, and fully insert the Incline Pins.
9. Make sure that all parts are properly tightened before
you use the treadmill. Keep the included hex key in a
secure place; the hex key is used to adjust the walking
belt (see page 14). To protect the floor or carpet, place a
mat under the treadmill.
Make
-
8
6, 7
87
7
41
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
Your treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply sili-
one spray or other substances to the walking belt or the walking platform. Such substances will deterio-
c
rate the walking belt and cause excessive wear.
HOW TO PLUG IN THE POWER CORD
This product must be earthed.
down, earthing provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped
with a power cord having an equipment-earthing conductor and an
earthing plug.
be replaced with a manufacturer-recommended power cord.
See drawing 1. Plug the indicated end of the power cord into the
socket on the treadmill.
See drawing 2. Plug the power cord into an appropriate outlet that is
properly installed and earthed in accordance with all local codes and
ordinances. Important: The treadmill is not compatible with
GFCI-equipped outlets.
Important: If the power cord is damaged, it must
If it should malfunction or break
1
Socket on Treadmill
Power
Cord
2
Outlet
DANGER: Improper connection of the equipment-earthing conductor can result in an in-
creased risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as
to whether the product is properly earthed. Do not modify the plug provided with the product—if it will
not fit the outlet, have a proper outlet installed by a qualified electrician.
9
DIAGRAM OF THE CONSOLE
Note: If there is a sheet of clear plastic
on the console, remove the plastic.
CAUTION: Before operating the
console, read the following precautions.
• Do not stand on the walking belt when turning on the power.
• Always wear the clip (see the drawing
above) while operating the treadmill.
• Adjust the speed in small increments to
avoid sudden jumps in speed.
• To reduce the possibility of electric shock,
keep
the console dry. Avoid spilling liquids
on the console and place only sealed water
bottles in the water bottle holders.
STEP-BY-STEP CONSOLE OPERATION
Key
Clip
Next, stand on the foot rails of the treadmill. Find the
clip attached to the key (see the drawing above), and
slide the clip securely onto the waistband of your
clothes. Then, insert the key fully into the console.
After a moment, the display will light. Important: In an
emergency situation, the key can be pulled from
the console, causing the walking belt to slow to a
stop. Test the clip by carefully taking a few steps
backward; if the key is not pulled from the console,
adjust the position of the clip.
Follow the steps below to operate the console.
Insert the key fully into the console.
1
A moment after the key is inserted,
light.
Press the Speed increase button to start the
2
walking belt.
the display will
Before operating the console, make sure that the
power cord is properly
plugged in (see page 9).
Next, locate the reset/off circuit breaker on the treadmill
frame near the power cord,
and make sure that the circuit breaker is in the reset
position.
Reset
A moment after the button is pressed, the walking
belt will begin to move at 1 mph. Hold the handrails
and begin walking. As you exercise, change the
speed of the walking belt as desired by pressing
the Speed increase and decrease buttons. Each
time a button is pressed, the speed setting will
change by 0.1 mph; if a button is held down, the
speed setting will change in increments of 0.5
mph.
10
To stop the walking belt, press the Stop button. If
the elapsed time is shown in the display (see step
), the time will begin to flash.
3
Note: The first time the treadmill is used, observe
the alignment of the walking belt, and center the
walking belt if necessary (see page 14).
Monitor your progress with the display.
3
As you exercise, the lower
left corner of
the display
can show the
elapsed time
and the distance (in
miles) that you have walked or run. The lower right
corner of the display can show the speed of the
walking belt (in miles per hour) and the approximate number of calories you have burned.
The upper half of the display is the
The priority display can show the elapsed time, the
distance that you have walked or run, the speed of
the walking belt, or the approximate number of
calories you have burned. Press the Mode button
repeatedly until the priority display shows the information that you are most interested in viewing.
Note: While information is shown in the priority display, the same information will not be shown in the
lower left or right corner of the display.
To reset the display, press the Stop button, remove the key, and then reinsert the key.
priority display.
When you are finished exercising, remove the
4
key from the console.
Step onto the foot rails, press the Stop button, and
remove the key from the console. Keep the key in a
ecure place. Then, switch the reset/off circuit
s
breaker to the “off” position and unplug the power
cord.
HOW TO CHANGE THE INCLINE OF THE TREADMILL
To vary the intensity of your exercise, you can change
the incline of the treadmill. There are three incline lev-
Before changing the incline, remove the key
els.
and unplug the power cord. Next, fold the treadmill
to the storage position (see page 12).
To change
the incline,
first remove
the incline pin
from one of
the incline
legs. Adjust
the incline leg
to the desired
height, and
fully reinsert
the incline
pin. Adjust
the other incline leg in the same way.
Before using the treadmill, make sure that both incline legs are at the same height and that both incline pins are fully inserted into the incline legs.
After you have adjusted the incline legs, lower the
treadmill (see page 12).
Incline
Pin
Incline
Leg
Incline
Pin
CAUTION:
1
1
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Unplug the power cord. CAUTION: You must be able to
safely lift 20 kg (45 lbs.) to raise, lower, or move the
readmill.
t
1. Hold the metal frame firmly in the location shown by
the arrow at the right. CAUTION: To decrease the possibility of injury, do not lift the frame by the plastic
foot rails. Make sure to bend your legs and keep your
back straight. As you raise the frame, make sure to lift
with your legs rather than your back.
about halfway to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob
to the left and hold it. Raise the frame until the hole in the
catch is aligned with the latch pin. Slowly release the
latch knob;
serted into the catch.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in temperatures above 30° C (85° F).
make sure that the latch pin is fully in-
Raise the frame
1
Frame
2
Latch
Pin
Knob
Catch
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the latch
pin is fully inserted into the catch.
1. Hold the handrails and place one foot against a wheel.
Tilt the treadmill back until it rolls freely on the wheels.
2.
Carefully move the treadmill to the desired location.
move the treadmill without tipping it back. To reduce
the risk of injury, use
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
3. Place one foot against one of the wheels, and carefully
lower the treadmill until it is in the storage position.
HOW TO LOWER THE TREADMILL FOR USE
1. See drawing 2 above. Hold the treadmill with your right hand as shown. Pull the latch knob to the left and hold
it. Pivot the frame down until it is past the latch pin.
2. See drawing 1 above. Hold the metal frame firmly with both hands, and lower it to the floor. CAUTION: To
decrease the possibility of injury, do not lower the frame by gripping only the plastic foot rails. Do not
drop the frame to the floor. Make sure to bend your legs and keep your back straight.
extreme caution while moving
Never
Handrail
Wheel
12
MAINTENANCE AND TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet. (See page 9.) If an ex-
tension cord is needed, use only a 3-conductor, 1 mm
m (5 ft.). Important: The treadmill is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the circuit breaker located on the treadmill
frame near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
d. Check the on/off switch located on the treadmill frame
near the power cord. Make sure that the switch is in
the “on” position.
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the
circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
2
(14-gauge) cord that is no longer than 1.5
c
Tripped
d
On
Position
Reset
c. Remove the key from the console. Reinsert the key into the console.
d. Make sure that the on/off switch is in the on position.
e. If the treadmill still will not run, see the front cover of this manual.
PROBLEM: The displays of the console do not function properly
SOLUTION: a.
Remove the key from the console and
POWER CORD.
two Foot Rail Screws (52). Next, remove the Hood (23).
Locate the Reed Switch (46) and the Magnet (49) on
the left side of the Pulley (53). Turn the Pulley until the
Magnet is aligned with the Reed Switch.
that the gap between the Magnet and the Reed
Switch is about 3 mm (1/8 in.).
the Screw (5), move the Reed Switch slightly, and
then retighten the Screw. Reattach the Hood, and run
the treadmill for a few minutes to check for a correct
speed reading.
Remove the four Screws (8) and the
UNPLUG THE
Make sure
If necessary, loosen
a
52
8
3 mm
Top View
46
23
52
5
8
8
53
49
13
PROBLEM: The walking belt slows when walked on
OLUTION: a
S
. If an extension cord is needed, use only a 3-conductor, 1mm
than 1.5 m (5 ft.).
b. If the walking belt is overtightened, treadmill perfor-
mance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE
POWER CORD. Using the hex key, turn both rear
roller bolts counterclockwise, 1/4 of a turn. When the
walking belt is properly tightened, you should be able
to lift each edge of the walking belt 5 to 7 cm (2 to 3
in.) off the walking platform. Be careful to keep the
walking belt centered. Then, plug in the power cord, insert the key, and walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened.
c. If the walking belt still slows when walked on, see the front cover of this manual.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt has shifted to the left, first re-
move the key and UNPLUG THE POWER CORD.
Using the hex key, turn the left rear roller bolt clockwise 1/2 of a turn. Be careful not to overtighten the
walking belt.
If the walking belt has shifted to the
right, turn the left rear roller bolt counterclockwise 1/2
of a turn. Then, plug in the power cord, insert the key,
and run the treadmill for a few minutes. Repeat until
the walking belt is centered.
2
14-gauge) cord that is no longer
(
b
–7 cm
5
Rear Roller
Bolts
a
b. If the walking belt slips when walked on, first remove
the key and
UNPLUG THE POWER CORD. Using
the hex key, turn both rear roller bolts clockwise, 1/4
of a turn. When the walking belt is correctly tightened,
you should be able to lift each edge of the walking
belt 5 to 7 cm (2 to 3 in.) off the walking platform. Be
careful to keep the walking belt centered. Then, plug
in the power cord, insert the key, and carefully walk
on the treadmill for a few minutes. Repeat until the
walking belt is properly tightened.
b
14
CONDITIONING GUIDELINES
WARNING: Before beginning
this or any exercise program, consult your
physician. This is especially important for individuals over the age of 35 or individuals
ith pre-existing health problems.
w
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
n the heart to pump blood to the muscles, and on the
o
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your exercise program. For more detailed exercise information, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the desired
results is to exercise with the proper intensity. The
proper intensity level can be found by using your heart
rate as a guide. The chart below shows recommended
heart rates for fat burning and aerobic exercise.
To find the proper heart rate for you, first find your age
at the top of the chart (ages are rounded off to the
nearest ten years). Next, find the three numbers below
your age. The three numbers are your “training zone.”
The lower two numbers are recommended heart rates
for fat burning; the highest number is the recommended heart rate for aerobic exercise.
HOW TO MEASURE YOUR HEART RATE
To measure your heart
rate, stop exercising
and place two fingers
on your wrist as
shown. Take a six-sec
ond heartbeat count,
and then multiply the
result by ten to find
your heart rate. (A six-second count is used because
your heart rate will begin to slow when you stop exercising.)
WORKOUT GUIDELINES
Each workout should include three important parts:
A Warm-up—Warming up prepares the body for exercise by increasing circulation, delivering more oxygen
to the muscles, and raising the body temperature.
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your heart rate is in
your training zone for 20 to 60 minutes. (During the
first few weeks of your exercise program, do not keep
your heart rate in your training zone for longer than 20
minutes.) Breathe regularly and deeply as you exer
cise—never hold your breath.
-
-
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time. During
the first few minutes of exercise, your body uses easily
accessible
the first few minutes does your body begin to use
stored
adjust the speed and incline of the treadmill until your
heart rate is near one of the lower two numbers in your
training zone.
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise
carbohydrate calories
fat calories
for energy. If your goal is to burn fat,
for energy. Only after
A Cool-down—Finish each workout with 5 to 10 minutes of stretching to cool down. This will increase the
flexibility of your muscles and will help to prevent postexercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
15
PART LIST—Model No. WATL16105.0 R0306A
Key No. Qty. Description
1 1 Console
2 4 Round Endcap
3 1 Key/Clip
4 1 Console Back
5 8 Electronics Screw
6 1 Right Handrail
7 1 Left Handrail
8 4 Hood Screw
9 2 Motor Tension Bolt
10 2 Frame Bolt
11 2 Rear Roller Bracket Screw
12 4 Handrail Bolt
13 2 Frame Spacer
14 2 Wheel Bolt
15 2 Wheel
16 1 Right Rear Roller Bracket
17 6 Nut
18 1 Belly Pan Grommet
19 6 Base Pad
20 23 13mm Screw
21 1 Latch Warning Decal
22 1 Wire Harness
23 1 Hood
24 1 Left Rear Roller Bracket
25 1 Belly Pan
26 4 Belt Guide Screw
27 2 Belt Guide
28 1 6mm Hex Key
29 1 4mm Hex Key
30 2 Handrail Washer
31 2 Platform Bolt, Front
32 1 Controller Bracket
33 1 Front Roller Star Washer
34 1 Front Roller Adj. Bolt
35 1 Controller
36
37
38 2
39
40 2 Outlet Plate Screw
41
42
43 1 Drive Motor Assembly
44
45 2
46 1 Reed Switch
47 2 Platform Bolt, Rear
1 Motor Bolt
1 Left Foot Rail
Motor Tension Nut
2
1
6
1 Power Cord
Motor Star Washer
Storage Latch Assembly
Base Pad Screw
Rear Roller Bracket Washer
Key No. Qty. Description
48 1 Reed Switch Clip
49 1 Magnet
50 1 Motor Belt
51 2 Roller Adj. Bolt
52 10 Foot Rail Screw
53 1 Front Roller/Pulley
54 1 Right Foot Rail
55 1 Frame
56 1 Walking Belt
57 1 Walking Platform
58 2 Motor Washer
59 2 Motor Bolt
60 2 Handrail Star Washer
61 8 8” Cable Tie
62 1 Dust Guard
63 2 Incline Leg
64 2 Incline Pin
65 1 Voltage Warning Decal
66 2 Roller Adj. Washer
67 2 Frame Endcap
68 2 U-nut
69 2 Cushion Fastener
70 4 Console Screw/Latch Screw
71 1 Base
72 1 Rear Roller
73 2 Outlet Plate Washer
74 2 Outlet Plate Nut
75 5 Nut
76 2 Platform Cushion
77 2 Front Isolator
78 1 Catch
79 1 Motor Bracket
80 1 Choke
81 3 Plastic Tie
82 4 Bracket Star Washer
83
84
85 4
86
87 6 16mm Screw
88
89
# 1 8” White Wire, Male/Female
#
#
Specifications are subject to change without notice.
2 Incline Leg Bolt
2 Incline Leg Nut
Incline Leg Washer
2
1
1
1 4” Black Wire, Male/Flag
1
Rear Roller Star Washer
Outlet Bracket Assembly
Filter Wire
User’s Manual
Handrail Washer (11)–2
2 3/4” Bolt (47)–4
Star Washer (81)–4
Washer (29)–4
3
Handrail Nut (17)–4
Frame Bolt (10)–2
Wheel Bolt (14)–2
Console Screw
(70)–4
Nut (17)–6
Base Pad
Screw (42)–6
Handrail Star
Washer (60)–2
Handrail Washer (30)–2
Handrail Bolt (12)–4
16mm Screw
(87)–6
4
” Bolt (120)–2
PART IDENTIFICATION CHART
Remove this chart and use it to identify small parts during assembly. Save this chart and the EXPLODED
RAWING/PART LIST for future reference.
D
65
81
20
20
27
29
61
57
55
47
56
37
26
49
46
5
48
76
27
25
1
3
6
71
2
17
15
15
14
17
17
23
88
21
13
10
13
7
17
30
60
30
10
60
68
68
51
66
22
12
12
22
19
42
42
19
42
18
2
70
2
4
87
87
87
63
9
39
38
36
43
75
19
70
19
42
19
42
14
42
19
40
40
8
20
20
20
8
8
52
47
20
11
63
64
64
52
52
52
52
51
66
52
52
69
69
50
87
41
32
5
35
5
5
80
9
52
20
77
77
20
59
20
62
67
67
78
20
79
2
39
53
54
16
24
33
34
26
76
73
73
74
74
28
75
75
83
84
84
83
82
20
85
85
72
86
86
58
58
8
31
31
85
85
45
11
45
44
89
EXPLODED DRAWING—Model No. WATL16105.0 R0306A
ORDERING REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 800-830-7240, or call:
Beijing: 010-60291670 Guizhou: 0851-5617855 Shengang: 024-22507779
Changchun: 0431-682499 Ha’erbin: 0451-82702754 Shenzhen: 0755-83248325
Changsha: 0731-4825618 Hefei: 0551-4238040 Shijiazhuang: 0311-86219246
Chengdu: 028-86927825 Jinan: 0531-86292209 Wuhan: 027-87275455
Chongqing: 023-65457730 Kunming: 0871-3130512 Xi’an: 029-87891305
Dongquan: 0769-2333575 Nanjing: 025-85640306 Xinjiang: 0991-8813186
Fuzhou: 0591-87734032 Nanning: 0711-5331007
Guangzhou: 020-37652666 Shanghai: 021-28323250/28323233
When ordering parts, please be prepared to provide the following information:
• the MODEL NUMBER of the product (WATL16105.0)
• the NAME of the product (WESLO A-40 treadmill)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING
attached in the center of this manual)
LIMITED WARRANTY
Goodfamily, Inc. (Goodfamily), warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of ninety (90) days from the date of purchase.
This warranty extends only to the original purchaser. Goodfamily's obligation under this warranty is limited to replacing or repairing, at Goodfamily's option, the product through one of its authorized service
centers. All repairs for which warranty claims are made must be pre-authorized by Goodfamily. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by a Goodfamily authorized
service center; products used for commercial or rental purposes; or products used as store display models. No other warranty beyond that specifically set forth above is authorized by Goodfamily.
Goodfamily is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or damages with respect to any economic loss,
loss of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or
other consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation
of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
Part No. 236099 R0306A
Goodfamily, Inc.
Printed in China
2006 ICON IP, Inc.
©
Loading...