Page 1
USER'S MANUAL
Model No. WCTL28090
Serial No.
Write the serial number in the
space above for future reference.
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or find that there
are missing or damaged parts,
we will guarantee you complete
satisfaction through direct assistance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained technicians on our Customer Hot Line
will provide immediate assistance, free of charge to you.
CUSTOMER HOT LINE:
1-888-936-4266
Mon.–Fri., 8 a.m.–6:30 p.m. EST
(excluding holidays)
®
Visit our website at
www.weslo.com
new products, prizes,
fitness tips, and much more!
Page 2
2
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
MAINTENANCE AND TROUBLE-SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
CUSTOMER RECORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
Note: APART LIST and an EXPLODED DRAWING are attached in the center of this manual. Remove the PART
LIST and EXPLODED DRAWING before beginning assembly.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
2. Use the treadmill only as described in this
manual.
3. Place the treadmill on a level surface, with
eight feet of clearance behind it. Do not place
the treadmill on a surface that blocks any air
openings. To protect the floor or carpet from
damage, place a mat under the treadmill.
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
7. The treadmill should not be used by persons
weighing more than 250 pounds.
8. Never allow more than one person on the
treadmill at a time.
9. Wear appropriate exercise clothing when
using the treadmill. Do not wear loose
clothing that could become caught in the
treadmill. Athletic support clothes are recommended for both men and women. Always
wear athletic shoes. Never use the treadmill
with bare feet, wearing only stockings, or in
sandals.
10. When connecting the power cord (see HOW
TO PLUG IN THE POWER CORD on page 7),
plug the power cord into a surge protector
(not included) and plug the surge protector
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be
on the same circuit.
11. Use only a CUL-listed surge protector, rated
at 15 amps, with a 14-gauge cord of five feet
or less in length. Do not use an extension
cord.
12. Keep the power cord and the surge protector
away from heated surfaces.
13. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 4 if the treadmill is not working properly.)
14. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read
the following important precautions and information before operating the treadmill.
Page 3
3
15. The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
16. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
17. Never leave the treadmill unattended while it
is running. Always remove the key when the
treadmill is not in use.
18. Do not change the incline of the treadmill by
placing objects under the treadmill.
19. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 5, and HOW TO MOVE
THE TREADMILL on page 10.) You must be
able to safely lift 45 pounds in order to raise,
lower, or move the treadmill.
20. When storing the treadmill, make sure that
the storage latch is fully closed.
21. Inspect and tighten all parts of the treadmill
every three months.
22. Never insert any object into any opening.
23.
DANGER:
Always unplug the power cord
before performing the maintenance and
adjustment procedures described in this
manual. Never remove the motor hood
unless instructed to do so by an authorized
service representative. Servicing other than
the procedures in this manual should be performed by an authorized service representative only.
24. This treadmill is intended for in-home use
only. Do not use this treadmill in any commercial, rental, or institutional setting.
WARNING:Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decal shown at the right has been
placed on your treadmill. If the decal is
missing, or if it is not legible, please call
our Customer Service Department, tollfree, to order a free replacement decal
(see ORDERING REPLACEMENT PARTS
on the back cover of this manual). Apply
the decal in the location shown.
Page 4
4
BEFORE YOU BEGIN
Thank you for selecting the WESLO®CADENCE 1020
treadmill. The CADENCE 1020 treadmill combines
advanced technology with innovative design to let you
enjoy an excellent form of cardiovascular exercise in
the convenience and privacy of your home. And when
you’re not exercising, the unique CADENCE 1020 can
be folded up, requiring less than half the floor space of
other treadmills.
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
please call our Customer Service Department toll-free
at 1-888-936-4266, Monday through Friday, 8 a.m.
until 6:30 p.m. Eastern Standard Time (excluding holidays). To help us assist you, please note the product
model number and serial number before calling. The
model number of the treadmill is WCTL28090. The
serial number can be found on a decal attached to the
treadmill (see the front cover of this manual for the
location).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Handrails
Console
Storage Latch
Speed Control
Key/Clip
Circuit Breaker
Handrail
Knobs
Walking Belt
Foot Rails
Power Cord
Cushioned Deck
BACK
RIGHT SIDE
Rear Roller
Adjustment Bolts
Incline Leg
Water Bottle Holder
(bottle not included)
Accessory Tray
Book Rack
Page 5
1. Note that the Right Handrail (32) and the Console
Base (not shown) are connected to the treadmill by
the Wire Harness (53). During assembly steps 1
through 5, be careful to avoid pulling on or damaging the Wire Harness.
With the help of a second person, carefully lay the
treadmill onto one side. Insert one of the Base Legs
(44) into the Upright (38) as shown. Make sure that
the Base Leg Pad (33) is in the indicated position.
Using the included Allen Wrench (81), attach the
Base Leg with a Base Leg Screw (39). Attach the
other Base Leg (44) in the same way.
With the help of a second person, carefully raise the
treadmill to the upright position so that both Base
Legs (44) are resting flat on the floor.
2. Carefully lower the treadmill. Remove the two indicated Latch Screws (8) and the shipping bracket
from the left Upright (38). Save the Latch Screws
for use in assembly step 3; discard the shipping
bracket.
3. Remove the two remaining Latch Screws (8) from
the left Upright (38).
Remove the cardboard and tape from the Latch (67).
Attach the Latch to the left Upright (38) with the four
Latch Screws (8). Make sure that the Latch
Screws are tight, but do not overtighten them; if
the Latch Screws are overtightened, the Latch
(67) will not slide smoothly.
Note: The inset drawing shows how the parts of the
Latch (67) fit together.
1
5
81
44
39
38
44
33
33
39
32
53
ASSEMBLY
Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench
and your own phillips screwdriver and scissors .
2
8
38
Shipping
Bracket
8
67
38
3
67
Page 6
4. Attach a Handrail Cover (63) and the Left Handrail (4)
to the left Upright (38) with two Handrail Knobs (1) and
two Knob Washers (13). Do not tighten the Handrail
Knobs yet. If you are shorter than 5’ 8”, use the
upper two holes in the Handrail; if you are 5’ 8” or
taller, use the lower two holes.
Have a second person hold the Console Base (87)
and the Right Handrail (32) in the position shown.
Feed the excess Wire Harness (53) into the upper end
of the Handrail, and pull the excess from the lower
end of the Handrail. Then, insert the excess Wire
Harness into the right Upright (38).
Next, attach a Handrail Cover (63) and the Right
Handrail (32) to the right Upright (38) with two Handrail
Knobs (1) and two Knob Washers (13). Do not tight-
en the Handrail Knobs. Make sure that both
Handrails are at the same height.
Refer to the inset drawing. Insert a Handrail Plug (70)
into the unused hole in each Handrail (4, 32).
5. Set the Console Base (87) on the Handrails (4, 32).
Route the Wire Harness (53) as shown, and attach the
Console Base to the Handrails with the four Console
Screws (8). Make sure that the Handrail Screws are
tight, but do not overtighten them. Insert the excess
Wire Harness (53) into the Right Handrail.
Tighten the four Handrail Knobs (1) used in step 4.
6. The Console (11) requires three "AA" batteries (not
included); alkaline batteries are recommended. Open
the Battery Cover (12) and press the batteries into the
Console; the negative (–) ends of the batteries must
touch the springs. Close the battery cover, push up on
the tab, and then push the tab forward as shown in the
inset drawing. Be sure that the tab locks into place.
7. Remove the backing from the Adhesive Clip (80).
Press the Adhesive Clip onto the right Upright (38).
Press the Allen Wrench (81) into the Adhesive Clip.
8. Make sure that all parts are properly tightened
before you use the treadmill. Some parts may be left
over after assembly is completed. To protect the floor
or carpet from damage, place a mat underneath the
treadmill.
6
5
8
87
32
4
8
53
11 12
Batteries
Battery Cover Tab
7
81
38
80
70
4, 32
4
63
4
63
1
3
38
32
3
53
1
Ramps
6
13
13
87
53
Page 7
7
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBETMWALKING BELT
Your treadmill features a walking belt coated with
PERFORMANT LUBE
TM
, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking platform. They will deteriorate the walking belt and
cause excessive wear.
HOW TO PLUG IN THE POWER CORD
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances being turned on
or off. To decrease the
possibility of your
treadmill being damaged, always use a
surge protector (not
included) with your
treadmill.
Surge protectors are
sold at most hardware
stores and department
stores. Use only a CULlisted surge protector,
rated at 15 amps, with
a 14-gauge cord of five
feet or less in length.
This product must be
grounded. If it should
malfunction or break
down, grounding provides a path of least
resistance for electric
current to reduce the
risk of electric shock. This product is equipped with a
cord having an equipment-grounding conductor and a
grounding plug. Plug the power cord into a surge
protector, and plug the surge protector into an
appropriate outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge protector to a 2-pole receptacle as shown in drawing 2 if a properly grounded
outlet is not available.
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet
box covers are not grounded. Contact a qualified
electrician to determine if the outlet box cover is
grounded before using an adapter.
DANGER:Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
2
Grounded Outlet Box
Grounded Outlet Box
Grounding Plug
Treadmill Power Cord
Grounding Plug
Grounding Plug
Grounding Pin
Surge Protector
Grounding Pin
Grounding Pin
Adapter
Lug
Metal Screw
Grounded Outlet
Page 8
8
STEP BY STEP CONSOLE OPERATION
Before operating the console, make sure that the
power cord is properly plugged in. (See HOW TO
PLUG IN THE POWER CORD on page 7.) In addition,
make sure that batteries are installed in the console.
(See step 6 on page 6.) If there is a thin sheet of clear
plastic on the console, remove it.
Step onto the foot rails of the treadmill. Next, find the
clip attached to the key (see the drawing above). Slide
the clip onto your waistband.
Follow the steps below to operate the console.
Insert the key fully into the power switch.
Note: Inserting the key will
not turn on the displays.
The displays will turn on
when the display on/reset
button is pressed or when
the walking belt is started.
If you just installed batteries, the displays will
already be on.
Reset the console and start the walking belt.
Slide the speed control to
the RESET position.
Note: Each time the
walking belt is stopped,
the speed control must
be moved to the RESET
position before the walking belt can be restarted.
Next, slowly slide the speed control until the walking belt begins to move at slow speed. Carefully
step onto the walking belt and begin exercising.
Change the speed of the walking belt as desired
by moving the speed control.
To stop the walking belt, step onto the foot rails
and slide the speed control to the RESET position.
2
1
CAUTION:Before operating the
console, read the following precautions.
• Do not stand on the walking belt when turning on the power.
• Always wear the clip (see the drawing
above) while operating the treadmill. When
the key is removed from the console, the
walking belt will stop.
• Adjust the speed in small increments.
• To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and use only a sealable
water bottle.
DIAGRAM OF THE CONSOLE
Clip
KeySpeed Control
Displays
Incline Control
PulseSensor
Display On/Reset Button
Page 9
Follow your progress with the four displays.
TIME display—This
display shows the
elapsed time.
DISTANCE display—
This display shows
the distance that you
have walked or run, in
miles.
SPEED display—
This display shows the
speed of the walking
belt, in miles per hour.
CALORIES/FAT CALORIES/PULSE
display—This display
shows the approximate numbers of
calories and fat calories you have burned. (See FAT BURNING on
page 14.) Every seven seconds, the display will
change from one number to the other, as indicated by the mode arrows. This display also shows
your pulse when the pulse sensor is used (see
step 4).
The displays can be
reset, if desired, by
pressing the display
on/reset button.
Measure your pulse, if desired.
To measure your
pulse, stand on the
foot rails and place
your thumb on the
pulse sensor as
shown. The pulse sensor is pressure activated—fully press it
down. Do not press
too hard, or the circulation in your
thumb will be
restricted, and your
pulse will not be
detected. Next, raise your thumb slightly until the
heart-shaped indicator in the calories/pulse/fat
calories display flashes steadily. Hold your thumb
at this level. After a few seconds, three dashes will
appear in the display and your pulse will be
shown. Hold your thumb on the sensor for another
15 seconds for the most accurate reading.
If the displayed pulse appears to be too high or
too low, or if your pulse is not displayed, lift your
thumb off the sensor and allow the display to
reset. Press down again on the sensor as
described above. Make sure that your thumb is
positioned as shown, and that you are applying the
proper amount of pressure to the pulse sensor. Try
the sensor several times until you become familiar
with it. Remember to stand still while measuring
your pulse.
Adjust the incline of the treadmill as desired.
To change the incline, press the top or bottom of
the incline control until the desired incline level is
reached.
Turn off the power.
To turn off the power, simply wait for about
four minutes. If the walking belt is stationary and
the console buttons are not pressed for four minutes, the power will turn off automatically.
HANDRAIL ADJUSTMENT
The Handrails (4, 32) can be adjusted to either of two
different heights. Before adjusting the Handrails,
remove the key and unplug the power cord. Remove
the four Console Screws (8). While a second person
holds the Console Base (87), remove the Handrail
Knobs (1) and Handrail Covers (63). Note: Make sure
that the Knob Washers (13) stay on the Handrail
Knobs. Raise or lower the Handrails to the desired
height, being careful not to damage
the Wire Harness
(53). Re-attach the
Handrails with the
Handrail Knobs
and Handrail
Covers.
Important: If you
are 5’ 8” or taller,
use the lower
two holes; if you
are shorter than
5’ 8”, use the
upper two holes.
Make sure that
both Handrails
are at the same height. Do not tighten the Handrail
Knobs yet. Always attach each Handrail with two
Handrail Knobs. Attach the Console Base (87) (see
assembly step 5 on page 6). Insert a Handrail Plug
(70) into the unused hole in each Handrail (4, 32).
6
5
4
3
9
Pulse
Sensor
Pulse Indicator
Mode Arrow
4, 32
8
8
87
38
63
70
53
1
13
13
1
70
53
Page 10
10
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, unplug the power cord.
Caution: You must be able to safely lift 45 pounds in
order to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. To decrease the possibility of injury, bend
your legs and keep your back straight. As you raise
the treadmill, make sure to lift with your legs rather
than your back. Raise the treadmill about halfway to the
vertical position.
2. Move your right hand to the position shown at the right,
and hold the treadmill firmly. Raise the treadmill until the
storage latch locks over the frame guide. Make sure that
the storage latch closes fully over the frame guide.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the storage position in temperatures above 85° Fahrenheit.
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the
storage position as described above. Make sure that the
storage latch is locked fully over the frame guide.
1. Hold the upper ends of the handrails. Place one foot near
one of the front wheels as shown.
2. Tilt the treadmill back until it rolls freely on the front
wheels. Carefully move the treadmill to the desired location. Never move the treadmill without tipping it back.
To reduce the risk of injury, use extreme caution
while moving the treadmill. Do not attempt to move
the treadmill over an uneven surface.
3. Place one foot on the base, and carefully lower the tread-
mill until it is resting in the storage position.
Base Leg
Front Wheels
Closed
Frame
Guide
Storage
Latch
Page 11
11
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand
as shown. Using your left thumb, slide open the storage
latch and hold it open. Pivot the treadmill until the frame
is past the storage latch.
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. To decrease the possibility of
injury, bend your legs and keep your back straight.
Opened
Storage
Latch
Frame
Guide
Page 12
12
MAINTENANCE AND TROUBLE-SHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department tollfree at 1-888-963-4266, Monday through Friday, 8 a.m. until 6:30 p.m. Eastern Standard Time (excluding
holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppres-
sor is plugged into a properly grounded outlet (see page 7). Use only a CUL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less in length.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the con-
sole. See step 1 on page 8.
c. Check the circuit breaker located on the treadmill
frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped.
To reset the circuit breaker, wait for five minutes
and then press the switch back in.
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing
above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsert the key fully into the console. See step 1 on page 8.
d. If the treadmill still will not run, please call our Customer Service Department, toll-free.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Check the batteries in the console. If the batteries need to be replaced, see assembly step 6 on
page 6. Most problems are the result of drained batteries.
b. Remove the key from the console and UNPLUG
THE POWER CORD. Next remove the screws from
the hood and carefully remove the hood. Locate the
Reed Switch (89) and the Magnet (88) on the left side
of the Pulley (90). Turn the Pulley until the Magnet is
aligned with the Reed Switch. Make sure that the
gap between the Magnet and the Reed Switch is
about 1/8”. If necessary, loosen the Screw (28) and
move the Reed Switch slightly. Retighten the Screw.
Re-attach the hood, and run the treadmill for a few
minutes to check for a correct speed reading.
Tripped
Reset
c
88
89
28
Top
View
1/8”
90
Tripped
Reset
Page 13
13
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt has shifted to the left, first
remove the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn the left rear roller adjust-
ment bolt clockwise, and the right bolt counterclock-
wise, 1/4 of a turn each. Be careful not to overtighten
the walking belt. Plug in the power cord, insert the
key and run the treadmill for a few minutes. Repeat
until the walking belt is centered.
b. If the walking belt has shifted to the right, first
remove the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn the left rear roller adjust-
ment bolt counterclockwise, and the right bolt clock-
wise, 1/4 of a turn each. Be careful not to overtighten
the walking belt. Plug in the power cord, insert the
key and run the treadmill for a few minutes. Repeat
until the walking belt is centered.
c. If the walking belt slips when walked on, first
remove the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn both rear roller adjust-
ment bolts clockwise, 1/4 of a turn. When the walking
belt is correctly tightened, you should be able to lift
each side of the walking belt 2 to 3 inches off the
walking platform. Be careful to keep the walking belt
centered. Plug in the power cord, insert the key and
run the treadmill for a few minutes. Repeat until the
walking belt is properly tightened.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a CUL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less
in length.
b. If the walking belt is overtightened, treadmill perfor-
mance may decrease and the walking belt may be
permanently damaged. Remove the key and
UNPLUG THE POWER CORD. Using the allen
wrench, turn both rear roller adjustment bolts counter-
clockwise, 1/4 of a turn. When the walking belt is
properly tightened, you should be able to lift each
side of the walking belt 2 to 3 inches off the walking
platform. Be careful to keep the walking belt cen-
tered. Plug in the power cord, insert the key and run
the treadmill for a few minutes. Repeat until the walk-
ing belt is properly tightened.
c. If the walking belt still slows when walked on, please call our Customer Service Department toll-free.
Rear Roller
Adjustment Bolts
2”–3”
b
b
a
a
Page 14
14
CONDITIONING GUIDELINES
The following guidelines will help you to plan your
exercise program. Remember—these are general
guidelines only. For more detailed exercise information, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. To find the proper heart rate for
you, first find your age at the top of the chart below
(ages are rounded off to the nearest ten years). Next,
find the two numbers below your age. The two numbers are your “training zone.”
To measure your heart rate during exercise, use the
pulse sensor on the console. If your heart rate is too
high or too low, adjust the speed and incline of the
treadmill as needed.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for ener-
gy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the treadmill until your heart rate is near the low end of your
training zone. (See pages 8 and 9.)
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the middle of your training zone. (See
pages 8 and 9.)
WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-up
Start each workout with 5 to 10 minutes of stretching
and light exercise. Aproper warm-up increases your
body temperature, heart rate, and circulation in preparation for exercise.
Training Zone Exercise
After warming up, increase the intensity of your exercise until your pulse is in your training zone for 20 to
60 minutes. (During the first few weeks of your exercise program, do not keep your pulse in your training
zone for longer than 20 minutes.) Breathe regularly
and deeply as you exercise—never hold your breath.
A Cool-down
Finish each workout with 5 to 10 minutes of stretching
to cool down. This will increase the flexibility of your
muscles and will help prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months, you may complete up to five workouts each week if desired. The
key to success is to make exercise a regular and
enjoyable part of your everyday life.
WARNING:
Before beginning
this or any exercise program, consult your
physician. This is especially important for
individuals over the age of 35 or individuals
with pre-existing health problems.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
Page 15
15
ORDERING REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-888-963-4266, Monday
through Friday, 8 a.m. until 6:30 p.m. Eastern Standard Time (excluding holidays). To help us assist you, please
be prepared to give the following information when calling:
• The MODEL NUMBER of the product (WCTL28090)
• The NAME of the product (WESLO CADENCE
®
1020 treadmill)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED
DRAWING at the center of this manual).
ICON of Canada Inc.
900 de l’Industrie
St-Jérôme, Québec
Canada, J7Y 4B8
PLACE
STAMP
HERE
CUSTOMER RECORD
Model No.: Serial No.:
Retailer Name: Purchase Date:
Retailer Address:
Page 16
PART LIST—Model No. WCTL28090 R0201A
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the user’s manual for information about ordering replacement parts.
Key No. Qty. Description
1 4 Handrail Knob
2 4 Long Screw
3 2 Handrail Bracket
4 1 Left handrail
5 1 Strain Relief
6 1 Key/Clip
7 1 Incline Wire
8 10 Console Screw/Latch Screw
9 1 Speed Potentiometer
10 1 Speed Control
1 1* 1 Console Assembly
12 2 Battery Cover
13 4 Knob Washer
14 4 Belt Guide Screw
15 0 Not Used
16 2 Console Rack Screw
17 1 Front Isolator Spacer
18 1 Motor Belt
19 3 Motor Tension Bolt/Incline Leg Bolt
20 1 Motor Tension Washer
21 1 Tension Star Washer
22 1 Motor Pivot Nut
23 1 Motor/Pulley/Flywheel/Fan
24 1 Pulley/Flywheel/Fan
25 1 Motor
26 1 Motor Pivot Bolt
27 1 8” Cable Tie
28 12 Hood Screw
29 1 Hood
30 1 Hood Shield
31 12 Small Screw
32 1 Right Handrail
33 4 Base Leg Pad
34 1 Motor Belly Pan
35 1 Controller
36 2 Frame Pivot Bolt
37 2 Frame Pivot Washer
38 1 Upright/Base
39 2 Base Leg Screw
40 15 Washer
41 2 Wheel Bolt
42 2 Wheel
43 7 Wheel Nut/Incline Nut
44 2 Base Leg
45 1 Circuit Breaker
46 1 Grommet
47 1 Power Cord
48 1 Motor Tension Nut
49 1 Shock
50 1 Right Foot Rail
51 4 Platform Screw
52 1 Front Roller Adj. Bolt
53 1 Wire Harness
Key No. Qty. Description
54 1 Frame Pivot Spacer (Left)
55 2 Oval Isolator
56 12 Belly Pan Fastener
57 1 Choke
58 2 Belt Guide
59 1 Belly Pan
60 2 Isolator
61 1 Incline Control
62 1 Frame Pivot Spacer (Right)
63 2 Handrail Cover
64 3 Incline Bolt
65 1 Incline Bracket
66 1 Frame Guide Spacer
67* 1 Latch Assembly
68 1 Wire Tie
69 1 Wire Tie Clamp
70 2 Handrail Plug
71 1 Incline Motor
72 1 Incline Leg
73 2 Incline Wheel Bolt
74 2 Incline Wheel
75 4 Incline Leg Nut
76 16 Electronic Screw
77 1 Ground Wire
78 2 Rear Roller Adj. Bolt
79 1 Rear Endcap
80 1 Adhesive Clip
81 1 Allen Wrench
82 1 Latch Decal
83 1 Rear Roller
84 1 Frame
85 2 Rear Platform Screw
86 1 Left Foot Rail
87 1 Console Base
88 1 Magnet
89 1 Reed Switch
90 1 Front Roller/Pulley
91 1 Sensor Clip
92 1 Walking Platform
93 1 Walking Belt
94 1 Ratchet Screw
95 2 Leg Endcap
96 1 Frame Guide
97 1 Book Holder
98 1 Upright Grommet
# 1 8” White Wire, Pig Tail
# 1 8” Blue Wire, Pig Tail
# 1 14” Blue Wire, Male/Female
# 1 14” Red Wire, Male/Female
# 1 8” Red Wire, Male/Female
# 1 User’s Manual
* Includes all parts shown in the box
Page 17
REMOVE THIS EXPLODED DRAWING
AND PART LIST FROM THE MANUAL
Save this EXPLODED DRAWING and PART LIST for future reference.
Note: Specifications are subject to change without notice. For information about
ordering replacement parts, see the back cover of the User’s Manual.
34
Page 18
EXPLODED DRAWING—Model No. WCTL28090 R0201A
99
67*
8
28
31
99
40
44
95
37
5
36
28
8
7
31
45
46
47
43
42
48
41
49
50
33
31
76
89
88
43
54
51
36
37
98
53
52
40
51
91
90
76
55
51
76
32
76
41
42
43
76
39
62
43
76
92
93
3
31
2
38
55
51
2
70
63
13
35
1
40
39
76
56
33
44
57
58
76
59
60
56
76
56
85
40
31
40
34
40
40
31
95
31
33
40
80
56
28
28
29
30
28
26
23*
10
9
25
24
22
21
20
19
18
11*
12
28
61
28
28
Page 19
Part No. 156642 J02147-C R0201A Printed in Canada © 2001 ICON Health & Fitness, Inc.
LIMITED WARRANTY
ICON OF CANADA INC., (ICON), warrants this product to be free from defects in workmanship and material,
under normal use and service conditions, for a period of one (1) year from the date of purchase. This warranty
extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at ICON's option, the product at one of its authorized service centers. All products for which warranty claim
is made must be received by ICON at one of its authorized service centers with all freight and other transportation charges prepaid, accompanied by sufficient proof of purchase. All returns must be pre-authorized by
ICON. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized
service center, to products used for commercial or rental purposes, or to products used as store display models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature. Some provinces do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you. The warranty extended hereunder
is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some provinces do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from province to
province or so specified by the retailer of your equipment.
ICON OF CANADA, 900 de l’Industrie, St. Jérôme, QC J7Y 4B8
IMPORTANT: MAIL WITHIN 14 DAYS OF PURCHASE
NAME:
ADDRESS:
COUNTY:
MODEL NO.
RETAILER NAME:
PHONE:
POSTCODE:
SERIAL NO. PURCHASE DATE:
RETAILER ADDRESS:
1) Primary user(s) of product:
❏ Male ❏ Female ❏ Family
2) Age of primary user:
❏ 0–24 ❏ 35–44 ❏ 55–64
❏ 25–34 ❏ 45–54 ❏ 65 and over
3) Annual household income:
❏ 0–9,999 ❏ 15,000–19,999
❏ 10,000–14,999 ❏ 20,000+
4) How many times a week do you exercise?
❏ Less than 3 times ❏ 3 times or more
5) Have you ever purchased an ICON product before?
❏ Yes ❏ No
6) Where did you first see or hear about ICON products?
❏ Magazine ❏ Friend/relative
❏ Newspaper Ad ❏ Store
❏ Other
7) What was the primary reason for purchasing this ICON product?
❏ Store Employee ❏ Television Ads ❏ Colour
❏ Electronic Features ❏ Magazine Ads ❏ Price
❏ Product Design ❏ Product Innovation
❏ Other Features
8) Did you consider purchasing fitness equipment from another
manufacturer?
❏ No ❏ Yes
What other Manufacturer?
9) Based on your impression of what you have purchased,
would you buy another ICON product?
❏ Yes ❏ No ❏ No Opinion
If not, what other brand name equipment would you purchase?
10)What other type of exercise equipment do you own?
❏ Bicycle ❏ Exercise Cycle ❏ Treadmill
❏ Home Gym ❏ Weight Bench ❏ Stepper
❏ Cardio Glide ❏ Other
11)Which type of magazines do you read regularly?
❏ Sports ❏ Fitness ❏ Motoring
❏ Business ❏ Computer ❏ General
12) Do you wish to be sent further bulletins about ICON products?
❏ Yes ❏ No
THANK YOU FOR YOUR TIME
PRODUCT WARRANTY REGISTRATION
© 2001 ICON of Canada, Inc. Printed in Canada
WESLO is a registered trademark of ICON Health & Fitness, Inc.
™
of/du Canada Inc.
®
Loading...