Wesco 240240 User Manual

Stainless Steel Drum Handler SSDH

Operating Instructions and Parts Manual

Industrial Products, Inc.

Industrial Products, Inc.

The Wesco Stainless Steel Drum Handler units are 304 stainless
steel construction including Frame, Drum Grab, Hydraulic Pump,
Foot Pedal, Wheel Locks and Lifting Cable.
(Items Listed Below Shown in Figures 1 or 3)

- Wheels:
[Figure 1, Item 5].

- Casters: Phenolic wheel with stainless rig and bearing
[Figure 1, Item 3].

- Stainless Steel Hydraulic Pump: Copper pumping cylinder
seal [Figure 3, Item D1.1], Copper sealing ring [Figure 3,
Item C3.1].

- Stainless Steel Wire Rope Assembly: with zinc plated
copper compression sleeve [Figure 1, Item 11 and
Figure 3, Item L1.1].

- Stainless Steel Wire Rope Sheave: with bearing bronze
bushing [Figure 3, Item K1.1].

- Cable Guard: ABS plastic [Figure 1, Item 12].

- Carriage Rollers: UHMW Polyethylene [Figure 1, Item 7].

- Hand Grips: PVC [Figure 1, Item 17].

See nameplate on unit for capacity, load center, model number
and truck serial number. This product is manufactured by:

Wesco Industrial Products, Inc

1250 Welsh Road
North Wales, PA 19454
Tel: [phone] Fax: [phone]

Contact the factory for parts information and ordering.
Visit us on the web at www.wescomfg.com

Phenolic wheel with stainless frame and bearings

When unpacking the Wesco Product, check carefully for shipping
damage and missing parts. If damage has occurred or any parts
are missing, file a claim with the delivering carrier within 24 hours
and notify the dealer from whom the unit was purchased.

If the unit does not work properly, contact your dealer or the
factory (215-699-7031) for units less than 1 year old.

If units are older than 1 year, repairs can be made easily on site
with factory supplied parts.
NOTE: Do not send units to the factory for service without first
obtaining a “Return Merchandise Authorization” (RMA) number
from the customer service department. We will not be
responsible for merchandise returned without an RMA number.

LIMITED WARRANTY

WESCO INDUSTRIAL PRODUCTS (WESCO) warrants to the purchaser of this product for a period of one year from the date of purchase that this product shall be free of
defects in material and/or workmanship, as follows:

1. WESCO will supply, at no charge, new or rebuilt replacements for any part that fails through a defect in material and/or workmanship during the warranty period. To obtain warranty
service, you must deliver the product prepaid, to the WESCO factory.

2. This warranty does not cover any product or product part which has been subject to accident, misuse, abuse or negligence. WESCO shall only be liable under this warranty if the
product is used the manner intended by the manufacturer as specified in the written instructions furnished with this product.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. ANY EXPRESS WARRANTY NOT PROVIDED IN
THIS WARRANTY DOCUMENT, AND ANY REMEDY FOR BREACH OF CONTRACT THAT, BUT FOR THIS PROVISION, MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW,
IS HEREBY EXCLUDED AND DISCLAIMED. UNDER NO CIRCUMSTANCES SHALL WESCO BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY, EXPRESS OR IMPLIED, A BREACH OF CONTRACT OR OTHERWISE. EXCEPT TO THE
EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY LIMITED
I

N DURATION TO THE DURATION OF THIS LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long any implied warranty lasts, so the above limitations may not
apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Description

Unpacking

Warranty Repairs

Non-Warranty Service

ATTENTION: TO INSURE SAFE AND EASY USE OF YOUR WESCO DRUM

HANDLER, READ THESE INSTRUCTIONS BEFORE USING.

General Safety Information

The Wesco Model SSDH is designed for specific functions. To
insure proper use, the following instructions must be adhered to:

(1) Load Rating: 800 lbs
(2) DO NOT use unit for loads exceeding the rated capacity.
(3) This product is designed for use on level floors only. DO

NOT use unit, or engage floor lock, on any incline greater
than five (5) degrees.

(4) Keep hands and feet clear of drum grab, carriage and

wheels.

(5) The drum grab must be in full contact with drum rim prior to

lifting. Using the manual lock is recommended, but not
necessary for operation.

(6) Be certain rim of fiber or plastic drum is able to withstand

the stress of drum lifting procedure.

(7) Be certain that both ends of lift cable are securely fastened

to jack and cable anchor before lifting load.

(8) DO NOT transport load at maximum height. Transport drum

2 to 3 inches off floor.

(9) Use extreme care when travelling over uneven floors.
(10) DO NOT use on ramps
(11) DO NOT modify this product in any way.
(12) Periodically inspect for damage, and loose or missing

hardware. If required remove unit from service.

Operation Instructions

Move unit towards drum until the bottom of the drum grab

(1)

firmly contacts the sidewall of the drum underneath the rim.
Note: Three sets of holes in the top of the carriage allow for
the adjustment of the drum grab for drums of different
heights. Raise the carriage above the frame upright until the
lowest adjustment hole clears the mast. While holding the
clamping head and slides with one hand, insert the
adjustment pin through the appropriate set of holes to obtain
the proper height for grabbing a drum

(2) Engage the floor lock and raise drum grab until grab

automatically clamps on the drum rim. If desired tighten the
drum grab manual lock by turning the knob clockwise. Once
secure raise the drum 2” to 3” off of the floor by stepping on
the pumping.

(3) Disengage the floor lock and transport drum to the desired

location.

(4) Engage floor lock and lower drum to floor by pressing relief

pedal located on left side of hydraulic jack. If the manual lock
was engaged, release the drum grab clamp by turning the
knob counter-clockwise.

Note: If drum is to be positioned on or moved from a
raised platform, use care during movement of drum in
raised position and keep drum at transportation height
whenever possible.

159282B

Stainless Steel Drum Handler SSDH

Operating Instructions and Parts Manual

Industrial Products, Inc.

Industrial Products, Inc. Industrial Products, Inc.

Item

Part No. Description Qty

1 056400 Jack: Stainless Assembly (40") 1
2 056472 Weldment: Jack/Carriage 1
3 109452 Caster: Swivel, 5x2, SS 2
4 109453 Floor Lock: 304SS 1
5 109454 Wheel: 5x2 Phenolic 2
6 056390 Drum Grab Automatic - S.S. 1
7 056481 Roller: Carriage (SSDH) 6
8 109491 Washer:SS,1/2"ID,1-1/4"OD 12
9 109492 Ring: Retaining, SS, 1/2" 6

Replacement Parts (1-9)

ATTENTION: TO INSURE SAFE AND EASY USE OF YOUR WESCO DRUM

NOTE: LOCATION OF CORNER RADIUS

UNDERCUT CRITICAL.

HANDLER, READ THESE INSTRUCTIONS BEFORE USING.

SLIDE HOLE LOCATION ON

DRUM GRAB IS CRITICAL

Replacement Parts (10-18)

Item Part No. Description Qty

10 109528 Screw: SS, Truss Hd (10-32 x 1/2) 4
11 056478 Assembly: Lift Cable 1
12 056479 Guard:"Wesco" SSDH 1
13 109527 Nut: SS, Hex Nylock, #10-32 4
14 109499 Magnet: Stainless Encased 2
15 108944 Ring: Circle, Cotter Pin 1
16 056480 Pin: Adjustment (SSDH) 1
17 108226 Handgrip: 1" Black PVC 2
18 056539 Sheave: SS, 1/4" Wire Rope 1

Figure 1

(CARRIAGE ASSEMBLY)

159282B