Wesco 240155 User Manual
Ergonomic Drum Handler DM-1100
Operating Instructions and Parts Manual
Industrial Products, Inc.
Industrial Products, Inc.
The Wesco Ergonomic Drum Handler DM-1100s are
designed specifically for lifting and transporting 30, 55 and 85
gallon steel, fiber and poly drums.
This product is distributed by:
Wesco Industrial Products, Inc
1250 Welsh Road
North Wales, PA 19454
Tel: 215-699-7031 Fax: 215-699-3836
Contact the factory for parts information and ordering.
Visit us on the web at www.wescomfg.com
When unpacking the Wesco Product, check carefully for
shipping damage and missing parts. If damage has occurred
or any parts are missing, file a claim with the delivering carrier
within 24 hours and notify the dealer from whom the unit was
purchased.
If the unit does not work properly, contact your dealer or the
factory (215-699-7031) for units less than 90 days old.
If units are older than 90 days, repairs can be made easily on
site with factory supplied parts.
NOTE: Do not send units to the factory for service without
first obtaining a “Return Merchandise Authorization” (RMA)
number from the customer service department. We will not
be responsible for merchandise returned without proper
authorization.
The Wesco Model DM1100 is designed for specific functions.
To insure proper use, the following instructions must be
adhered to:
(1) Load Rating: 1100 lbs./(legs extended) 650 lbs./(legs
retracted)
(2) DO NOT use unit for loads exceeding the rated capacity.
(3) This product is designed for use on level floors only. DO
NOT use unit, or engage floor lock, on any incline
greater than five (5) degrees.
LIMITED WARRANTY
WESCO INDUSTRIAL PRODUCTS (WESCO) warrants to the purchaser of this product for a period of ninety (90) days from the date of purchase that this product shall be free of
defects in material and/or workmanship, as follows:
1. WESCO will supply, at no charge, new or rebuilt replacements for any part that fails through a defect in material and/or workmanship during the warranty period. To obtain warranty
service, you must deliver the product prepaid, to the WESCO factory.
2. This warranty does not cover any product or product part which has been subject to accident, misuse, abuse or negligence. WESCO shall only be liable under this warranty if the
product is used the manner intended by the manufacturer as specified in the written instructions furnished with this product.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. ANY EXPRESS WARRANTY NOT PROVIDED IN
THIS WARRANTY DOCUMENT, AND ANY REMEDY FOR BREACH OF CONTRACT THAT, BUT FOR THIS PROVISION, MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW,
IS HEREBY EXCLUDED AND DISCLAIMED. UNDER NO CIRCUMSTANCES SHALL WESCO BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY, EXPRESS OR IMPLIED, A BREACH OF CONTRACT OR OTHERWISE. EXCEPT TO THE
EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY LIMITED
IN DURATION TO THE DURATION OF THIS LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long any implied warranty lasts, so the above limitations may not
apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
General Safety Information
Description
Unpacking
Warranty Repairs
Non-Warranty Service
ATTENTION: TO INSURE SAFE AND EASY USE OF YOUR WESCO DRUM
HANDLER, READ THESE INSTRUCTIONS BEFORE USING.
General Safety Information (cont’d)
(4) Keep hands and feet clear of clamping head, mast and
wheels.
(5) Clamping head must
prior to lifting.
(6) Be certain rim of fiber or plastic drum is able to withstand
the stress of drum lifting procedure.
(7) Be certain that both ends of lift chain are securely
fastened to jack and chain anchor before lifting load.
(8) DO NOT transport load at maximum height. Transport
drum 2 to 3 inches off floor.
(9) Use extreme care when travelling over uneven floors.
(10) DO NOT use on ramps
(11) DO NOT modify this product in any way.
(12) Periodically inspect for damage, and loose or missing
hardware. If required remove unit from service
be in full contact with drum rim
Operation Instructions
(1) Move unit towards drum until the clamping head firmly
contacts the sidewall of the drum.
Note: Three sets of holes in the top of the mast allow for
the adjustment of the clamping head to grab a drum.
(2) Raise the mast above the frame upright until the lowest
adjustment hole clears the mast. While holding the
clamping head and slides with one hand, insert the
adjustment pin through the appropriate set of holes to
obtain the proper height for grabbing a drum
(3) Engage the floor lock (if present) and raise the drum 2” to
3” off of the floor by stepping on the pumping pedal or
using the power lift.
Note: If a drum is to be moved from a raised platform,
engage the clamping head against the drum, raise the
load to clear the platform, and lower the drum to the
recommended height for transportation
(4) Disengage the floor lock (if present), and transport drum
to the desired location.
(5) Engage floor lock (if present), and lower drum to floor by
pressing relief pedal located on left side of hydraulic jack
or using the power lift.
Note: If drum is to be positioned on a raised platform,
raise the drum so that it clears the platform, move the
load to the required position, and lower the drum.
159131G
Ergonomic Drum Handler DM-1100
Industrial Products, Inc.
ATTENTION: TO INSURE SAFE AND EASY USE OF YOUR WESCO DRUM
Item Part No. Description
1 051618 Chain Roller Guard
2 053769 5x2 Phenolic Wheel
3 054267 Swivel Caster Assembly
4 055079 Gator Grip Jaw Assembly
5 055006 Chain Anchor
6 055007 RH Outrigger
054933
7 055008 LH Outrigger Weldment
054932
8 055090
054923
9 055016
051169
*10 052723 Hydraulic Jack Seal Kit
11 055286 Gator Grip Slide
12 055063 Adjustment Pin
13 150001
14 100069 Flat Washer (5/16 SAE)
492038
1
Spare Parts (1-13)
RH Outrigger Extended (For 240155 Only)
LH Outrigger Extended (For 240155 Only)
Guard Assembly
(For 240155 & 240150 Only)
Extended Guard Assembly
(For 240154, 240156 & 240157 Only)
40” Hydraulic Jack – Foot Pump
(For 240150, 240154 & 240155 Only)
28” Cylinder – Powered Model
(For 240156 & 240157 Only)
Floor Lock Assembly
(For Units Made Before 8/12)
Floor Lock Assembly
(For Units Made After 7/12)
27
8
12
Operating Instructions and Parts Manual
HANDLER, READ THESE INSTRUCTIONS BEFORE USING.
Spare Parts (14-34)
Item Part No. Description
15 100170 Lockwasher (5/16)
16 100642 Hex Nut (3/8-16)
17 105080 Socket Cap Screw (3/8-16x1-1/4)
18 105311 Spanner Bushing
19 108149 Hex Cap Screw (5/16-18 x 1”)
20 108161 Hex Cap Screw (1/2-13 x 3-1/3)
21 108174 Lock Hex Nut (1/2-13 2 Way Rev)
22 108175 Hex Nut (5/16-18)
23 108226 Handgrip
24 108427 Flat Washer (1/4 USS)
25 108918 Hex Cap Screw (1/4-20, 7/8L)
Cotter Pin (1/8 x 1”)
(For Units Made Before 8/12)
Retaining Ring 1/2”, Ext.
(For Units Made After 7/12)
Relief Pedal Assembly
(For 240150, 240154, 240155 Only)
Gator Grip Release Pin Replacement
Kit (Includes 2 Release Cams )
28
26 108943
100457
27 108944 Circle Cotter Pin
28 050853 Carriage Roller
29 100169 ¼” Lockwasher
30 108503 Lift Chain
31 108502 Connecting Link
32 108941 Flat Washer (1 OD x ½ ID)
33 108967 Chain Roller
*34 220802 Gator Grip Slide Kit (Includes 2 Slides )
35 055012
36 052250
* Items not shown in Figure 1
33
35
9
19
15
14
23
22
3
24
25
13
31
17
29
30
NOTE: LOCATION OF CORNER RADIUS
UNDERCUT CRITICAL.
32
26
11
16
4
SLIDE HOLE
LOCATION
ON GATOR
GRIP IS
“CRITICAL”
ASSEMBLE RADIUS
THIS LOCATION
5
6, 7
21
2
18
20
21
20
36
159131G
Hydraulic Jack
Industrial Products, Inc.
Operating Instructions and Parts Manual
ATTENTION: TO INSURE SAFE AND EASY USE OF YOUR WESCO HYDRAULIC
JACK, READ THESE INSTRUCTIONS BEFORE USING.
The Wesco Hydraulic Jacks are an exclusive design of the
manufacturer and under normal usage, will provide a long life
of service. The jacks are rated for 750 lb., 1000 lb., or 1100
lb. loads depending on the product.
This product is distributed by:
Wesco Industrial Products, Inc
1250 Welsh Road
North Wales, PA 19454
Tel: 215-699-7031 Fax: 215-699-3836
Contact the factory for parts information and ordering.
Visit us on the web at www.wescomfg.com
When unpacking the Wesco Product, check carefully for
shipping damage and missing parts. If damage has occurred
or any parts are missing, file a claim with the delivering carrier
within 24 hours and notify the dealer from whom the unit was
purchased.
If the unit does not work properly, contact your dealer or the
factory (215-699-7031) for units less than 90 days old.
If units are older than 90 days, repairs can be made easily on
site with factory supplied parts.
NOTE: Do not send units to the factory for service without
first obtaining a “Return Merchandise Authorization” (RMA)
number from the customer service department. We will not
be responsible for merchandise returned without proper
authorization.
The Wesco Hydraulic Jack is designed for specific functions.
To insure proper use, the following instructions must be
adhered to:
(1) DO NOT overload the jack above the rated capacity of
the unit.
(2) Jack should always be filled with hydraulic oil to filler
hole level. Oil level should be checked with the ram fully
retracted
General Safety Information
LIMITED WARRANTY
WESCO INDUSTRIAL PRODUCTS (WESCO) warrants to the purchaser of this product for a period of ninety (90) days from the date of purchase that this product shall be free of
defects in material and/or workmanship, as follows:
1. WESCO will supply, at no charge, new or rebuilt replacements for any part that fails through a defect in material and/or workmanship during the warranty period. To obtain warranty
service, you must deliver the product prepaid, to the WESCO factory.
2. This warranty does not cover any product or product part which has been subject to accident, misuse, abuse or negligence. WESCO shall only be liable under this warranty if the
product is used the manner intended by the manufacturer as specified in the written instructions furnished with this product.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. ANY EXPRESS WARRANTY NOT PROVIDED IN
THIS WARRANTY DOCUMENT, AND ANY REMEDY FOR BREACH OF CONTRACT THAT, BUT FOR THIS PROVISION, MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW,
IS HEREBY EXCLUDED AND DISCLAIMED. UNDER NO CIRCUMSTANCES SHALL WESCO BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY, EXPRESS OR IMPLIED, A BREACH OF CONTRACT OR OTHERWISE. EXCEPT TO THE
EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY LIMITED
IN DURATION TO THE DURATION OF THIS LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long any implied warranty lasts, so the above limitations may not
apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Description
Unpacking
Warranty Repairs
Non-Warranty Service
(3) When lowering platform or forks, apply foot pressure
(4) A sealing label has been placed over the breather
(5) Custom alterations of units for specific
Jack Start Up:
To be certain your unit is in working order, place an
approximately 200 lb. load on the platform; fork; or in the
case of the Drum-Master, a drum weighing approximately 200
lbs. and pump the load to full height at least 5 or 6 times.
If jack does not pump or pumps only slightly at the outset,
pump the pedal vigorously at least 12 times to dislodge any
air pockets that might have located in the unit during
shipment.
If this procedure does not correct the problem; loosen
assembly retainer (see Figure 1) and pump the pedal once or
twice. This will cause the oil to flow, breaking any air lock that
might exist. Re-tighten the assembly retainer before using the
unit.
If the unit does not reach proper height, the oil reservoir is low
and additional hydraulic fluid should be added. This can be
done by removing both fill screws (See Parts Drawing) and
washers and filling to level of the lower hole. Use premium
grade ISO #32 Anti-Wear Hydraulic Pump oil. The oil must be
perfectly clean, we recommend straining the oil prior to use.
After filling it may be necessary to rebleed the unit as
described above. If any oil leaks exist after completion of
above procedure, contact your dealer immediately.
General Safety Information (cont’d)
slowly to release pedal to properly determine and control
downward speed. DO NOT Depress the pedal fully when
loaded without performing the above test.
hole of the jack to prevent leakage during shipment.
This label must be removed prior to use. See parts
list drawing for hole location.
functions, not made at the factory, void all
warranties without exceptions. User-made
alterations may result in unsafe conditions
during use of unit.
Operation Instructions
159132E
Loading...