Werner H012002, H012001, H013002, H013001, H032102 User Manual

USER INSTRUCTIONS

FULL BODY HARNESS

Complies with the ANSI Z359.11 standard and OSHA 29 CFR 1910 and 1926 regulations.

(This manual applies to all harnesses with model numbers starting with H0 and H9)

WARNING!

Compliant fall protection equipment must only be used as it was designed. Users MUST read and follow
all user instructions provided with the product. Before using a fall arrest system, users must be trained in
the safe use of the system, as required by OSHA 29 CFR 1910.30 and 1926.503, or local safety regulations.

Misuse or failure to heed these warnings and instructions may result in injury or even death.

WORK SAFE! WORK SMART!

IF YOU HAVE ANY QUESTIONS ABOUT THE PROPER USE OF THE EQUIPMENT, SEE YOUR SUPERVISOR, USER
INSTRUCTIONS, OR CONTACT WERNER CO. FOR MORE INFORMATION.

USE INSTRUCTIONS AND LIMITATIONS

IMPORTANT

Before use, the user must read and understand these User Instructions. Keep these User Instructions for
reference.

PURPOSE

The Full Body Harness is designed to be used as part of a complete personal fall arrest, restraint, rescue, ladder
climbing, or work positioning system.

USE INSTRUCTIONS

1. Failure to follow all instructions and limitations on the use of the Full Body Harness may result in serious
personal injury or death.

2. Before using a personal fall arrest system, employees must be trained in accordance with the requirements of
OSHA 29 CFR 1910.30 and 1926.503 in the safe use of the system and its components.

3. Personal fall arrest systems, including the Full Body Harness, must be inspected prior to each use for wear,
damage, and other deterioration. Defective components must be immediately removed from service, in
accordance with the requirements of OSHA 29 CFR 1910.140 and 1926.502.

4. The complete fall protection system must be planned (including all components, calculating fall clearance,
and swing fall) before using.

5. Users must have a rescue plan, and the means to implement it, that provides for the prompt rescue of
employees in the event of a fall, or assures that employees are able to rescue themselves.

6. Store the Full Body Harness in a cool, dry, clean environment and out of direct sunlight when not in use.

7. After a fall occurs on the system, immediately remove from service until a “competent person” can make the
determination for reuse or disposal.

USE LIMITATIONS

1. CAPACITY: The Full Body Harness is designed for users with a capacity (including clothing, tools, etc.) up to
400 pounds (181 kg) total working weight, in conjunction with compatible connecting components.

WARNING!

Not all fall protection components are rated for the same user weight capacity. Only use components
rated for the same weight capacity.

2. FREE FALL: Personal fall arrest systems must be rigged in such a way to limit the free fall to 6 ft. (1.83 m)
(OSHA 1910.140 and1926.502). Work positioning systems must be rigged so that free fall is limited to 2 ft.
(0.6 m) or less. Climbing systems must be rigged so that free fall is limited to 1.5 ft. (0.46 m) or less. Restraint
systems must be rigged such that there is no possible vertical free fall. See associated connecting subsystem
manufacturer’s instructions for further information.

3. FALL CLEARANCE: Ensure that enough clearance exists in your fall path to prevent striking an object. The
amount of clearance required is dependent upon the type of connecting subsystem used (energy absorbing
lanyard, self retracting lifeline), the anchorage location, and the amount of stretch in the harness.

WARNING!

The Full Body Harness Stretch (FBH Stretch) and additional length of a D-ring extender must be taken
into consideration during the clearance calculation process.

4. EXTENDED SUSPENSION: The Full Body Harness is not intended for use in extended suspension
applications.

5. CORROSION: Do not leave the Full Body Harness in environments where corrosion of metal parts could take
place as a result of vapors from organic materials. Use near seawater or other corrosive environments may
require more frequent inspections to ensure corrosion damage is not affecting the performance of the product.

6. CHEMICAL HAZARDS: Solutions containing acids, alkali, or other caustic chemicals, especially at elevated
temperatures, may cause damage to the Full Body Harness. When working with such chemicals, frequent
inspection of this equipment must be performed. Contact Werner Co. with any questions concerning the use
of the Full Body Harness around chemical hazards.

7. EXTREME TEMPERATURE: The Full Body Harness is designed to be used in temperatures ranging
from -40ºF to +130ºF (-40°C to +54°C). Protection should be provided for Full Body Harness when used
near welding, metal cutting or similar activities. Contact Werner Co. with any questions concerning high
temperature environments.

8. ELECTRICAL HAZARDS: Use extreme caution when working near high voltage power lines due to the
possibility of electric current  owing through the Full Body Harness or connecting components.

9. HEALTH: Minors, pregnant women and anyone with a history of either back or neck problems should not use
this equipment.

1. TRAINING: Do not use the Full Body Harness without proper training from a “competent person” as de ned by OSHA
29 CFR 1910.140(b) and 1926.32(f).

2. REPAIRS: Only Werner Co., or persons or entities authorized in writing by Werner Co., may make repairs or alterations
to the equipment.

ANCHORAGES

All anchorage requirements depend on the application which the Full Body Harness is used. In a personal fall arrest system
the anchorage must meet the requirements of OSHA 29 CFR 1910 and 1926. OSHA states:

Anchorages must be capable of supporting at least 5,000 pounds (22.2 kN) for each employee attached; or designed,
installed, and used, under the supervision of quali ed person, as part of a complete personal fall protection system
that maintains a safety factor of at least two.

ANSI Z359.2 states that anchorages selected for fall arrest systems must have a strength capable of sustaining static loads,
applied in all permitted directions by the system:

(a) no less than 5,000 pounds (22.2 kN) for non certi ed anchorages; or
(b) at least two times the maximum arresting force for certi ed anchorages;

When more than one fall arrest system is attached to an anchorage, the strengths set forth in (a) and (b) above shall be
multiplied by the number of systems attached to the anchorage.

Anchorages used in restraint systems must be capable of supporting loads of 1,000 lbf (4.5 kN) for non-certi ed anchorages
or at least two times the foreseeable force for certi ed anchorages per ANSI Z359.2.

Anchorages used in work positioning systems must be capable of supporting loads of 3,000 lbf (13.3 kN) for non-certi ed
anchorages or two times the foreseeable force for certi ed anchorages per ANSI Z359.2.

Anchorages used in controlled descent and rescue systems must be capable of supporting loads of 3,100 lbf (13.8 kN) for
non-certi ed anchorages or a 5:1 safety factor for certi ed anchorages per ANSI Z359.4-2007.

SWING FALL

All anchorages should be located vertically above the user’s head and be
positioned as to not exceed the maximum allowable free fall for the system.

Anchorages

HAZARD

SWING FALLS

To minimize the possibility of a swing fall, anchor as directly above the work
area as possible. Striking objects horizontally, due to the pendulum effect,
may cause serious injury. Swing falls also increase the vertical fall distance of
a worker, compared to a fall directly below the anchorage connector. Swing
falls may be reduced by using overhead anchorage connectors that move
with the worker.

Correct Incorrect

DONNING AND USE

WARNING!

Before using a personal fall arrest system, employees must be trained in accordance with the requirements of
OSHA 29 CFR 1910.30 and 1926.503 and/or applicable local, state, governmental and jurisdictional agencies, in the
safe use of the system and its components.

Personal fall arrest systems, including Full Body Harnesses, must be inspected prior to each use for wear, damage,
and other deterioration, and defective components must be immediately removed from service in accordance with
the requirements of OSHA 29 CFR 1910.140 and 1926.502 and/or applicable local governmental and jurisdictional
standards.

DONNING

1. Hold the dorsal (back) D-ring of the Full Body Harness and shake to allow all straps to fall into place. Ensure straps are
not buckled or twisted.

2. Slip shoulder strap over one shoulder, then pull the other shoulder strap around the back and over the second shoulder,
just like putting on a jacket. The dorsal D-ring will be located on your back, while the chest strap is located in the front.
Straps must not be tangled as the harness hangs freely from shoulders.

3. Pull one leg strap between your legs and connect it to the opposite end on the same side. See Fitting for speci c
connecting type. Repeat with second leg strap. Ensure that the leg straps are not twisted or crossed.

WARNING!

Failure to have the leg straps of a Full Body Harness connected and properly adjusted in the event of a fall arrest
may result in serious personal injury or death.