Werner A100203, A100202, A100204 User Manual
FALL PROTECTION
PROTECCIÓN CONTRA CAÍDAS
USER INSTRUCTIONS
INSTRUCCIONES PARA EL USUARIO
HAND GRIP ANCHOR
Complies with ANSI Z359.1-2007, OSHA 1910 and 1926 requirements.
ANCLAJE DE AGARRE MANUAL
Cumple con las normas ANSI Z359.1-2007, OSHA 1910 y 1926.
(This manual applies to hand grip anchors A100202, A100203 and A100204.)
(Este manual aplica a los anclajes de agarre manual
A100202, A100203 y A100204.)
Werner Fall Protection 724-588-2000
93 Werner Rd. 888-523-3371 toll free/ llamada gratuita
Greenville, PA 16125 888-456-8458 fax
CAUTION!
If use of fall protection equipment is necessary then the work
environment is dangerous and potentially deadly. Werner Company
products are designed to eliminate as much of the hazard as possible
but can do that ONLY if they are used correctly. Use this equipment as
it was designed to be used, after appropriate training, under the direct
supervision of a competent person, according to the instructions
provided, and in accordance with OSHA and local safety regulations.
User MUST read and understand all cautions and instructions. Failure
to heed these guidelines could result in injury or even death. Please,
WORK SAFE! WORK SMART!
ENGLISH
Page 2
HAND GRIP ANCHOR
USER INSTRUCTIONS
Contents
I. BEFORE USING THE HAND GRIP ANCHOR ................................................... 4
a. Inspect ......................................................................................................................4
b. Compatibility ............................................................................................................5
c. Fall Protection Plan ..................................................................................................6
d. Training .....................................................................................................................8
II. HAND GRIP ANCHOR INSTALLATION AND USE .......................................... 8
a. Making a Connection ...............................................................................................8
b. Anchorage Strength ..............................................................................................10
c. Lanyard ...................................................................................................................11
d. Body Support .........................................................................................................11
e. Attaching the Hand Grip to an Anchorage ...........................................................11
f. Connecting to the Body Support ..........................................................................12
g. Connecting to the Hand Grip ................................................................................12
h. After Use .................................................................................................................12
III. USE WARNINGS, RESTRICTIONS AND CAUTIONS ................................... 13
a. Purpose ..................................................................................................................13
b. Rated Capacity .......................................................................................................13
c. Limitations ..............................................................................................................13
IV. LABELS/IDENTIFICATION/INSPECTION RECORDS .................................. 14
V. EQUIPMENT RECORDS ................................................................................16
VI. INSPECTION RECORDS .............................................................................. 16
ENGLISH
Page 3
Warning:
This product is just one part of a personal fall arrest system. It must
be matched correctly with other components to form a complete and
functional system. The user must understand the function of each of
these components and follow the manufacturer’s instructions for use
for each. The user must be provided these instructions, should read
and follow them, and consult the competent person who will supervise
his work if he has any questions about any part of the instructions.
The employer must provide training in the proper use, inspection, and
maintenance of all components in the system, and these instructions
can be used as part of that training. The equipment should be used
ONLY in accordance with these instructions, local ordinances and
codes, the applicable OSHA and ANSI standards, and the employer’s
safety plan. Alterations or misuse of this product or failure to follow
instructions may result in serious injury or death.
IF YOU HAVE ANY QUESTIONS ABOUT ANYTHING IN THESE
INSTRUCTIONS, THE EQUIPMENT, OR PROPER USE OF THE
EQUIPMENT, CONTACT WERNER CO. FOR MORE INFORMATION.
I. Before Using the Hand Grip
Before using this equipment the user should take certain steps to
ensure that it is in suitable condition and safe for use. Users must
read and understand these instructions. It is the employer’s obligation
to ensure that all users have been trained in safe work procedures
as well as in the use and limitations of fall protection equipment. All
users should be aware of and comply with all applicable OSHA, ANSI
and local or regional regulations concerning fall protection equipment
and its use.
a. Inspect
Examine all equipment thoroughly, daily before use by the user,
and periodically by a competent person who is not the user.
1. Before installation or use of this equipment, carefully inspect it to
assure it is in serviceable and usable condition.
2. The hand grip anchor must be inspected by a competent person
ENGLISH
other than the user at least annually. Record the results of each
formal inspection in the inspection log.
Page 4
HAND GRIP ANCHOR
USER INSTRUCTIONS
3. Inspect the device for damage, wear, and corrosion.
4. Inspect for misaligned, bent, or twisted components. Verify the
hook portion passes through the loops on either side of the
device.
5. Inspect each system component or subsystem per associated
manufacturer’s instructions.
6. Record the inspection date and results in the inspection log.
7. If inspection reveals a defective condition or abnormalities in
any of these areas, remove unit from service immediately. A
competent person should be consulted to determine if that item
is safe for continued use or if it should be destroyed.
IMPORTANT: If this equipment has been subjected to forces
resulting from the arrest of a fall, it must be immediately removed
from service.
IMPORTANT: Do not attempt to alter, repair, or make substitutions to
the hand grip anchor. Equipment found to be in defective condition
must be removed from service. Repairs may only be performed by
Werner Co. or those authorized in writing to do so.
b. Compatibility
Werner Co. equipment is designed for use with Werner Co. approved
components and subsystems only. Substitutions or replacements
made with non-approved components or subsystems may
jeopardize compatibility of equipment and may affect the safety and
reliability of the complete system.
Connectors are considered to be compatible with connecting
elements when they have been designed to work together in
such a way that their sizes and shapes do not cause their gate
mechanisms to inadvertently open regardless of how they become
oriented. Contact Werner Co. if you have any questions about
compatibility. Connectors (hooks, carabiners, and D-rings) must be
capable of supporting at least 5,000 lbs. (22.2kN). Connectors must
be compatible with the anchorage or other system components.
Do not use equipment that is not compatible. Non-compatible
connectors may unintentionally disengage. Connectors must be
compatible in size, shape, and strength. Self locking snap hooks
and carabiners are required by ANSI Z359 and OSHA.
Page 5
ENGLISH
Total Fall
Distance
(Free Fall +
Deceleration)
Free Fall
Working Level
Lower Level or Obstruction
Energy
Absorbing
Lanyard
Length of Anchorage Connector
6 ft.
Length of Lanyard
1/2 ft.
Anchorage Stretch
11 ft.
4 ft.
Deceleration Free Fall Distance
2 ft.
Safety Factor
1 ft. Harness Stretch
5 ft.
To Worker’s Back D-Ring
Total Estimated
Fall Distance
18.5 ft.
c. Fall Protection Plan
Plan your fall arrest or restraint system before starting your work.
Take into consideration all factors affecting your safety at any
time during use. The following list gives some important points to
consider when planning your system:
1. ANCHORAGE: Select a rigid anchorage point that is capable of
supporting the required loads. See section II.b.
The anchorage location must be carefully selected to reduce
possible free fall and swing fall hazards and to avoid striking an
object during a fall. For restraint systems the anchorage must be
located such that no vertical free fall is possible. For fall arrest
systems OSHA requires the anchorage be independent of the
means suspending or supporting the user.
2. FREE FALL: Do not work above the anchorage level, increased
fall distance will result. Personal fall arrest systems must be
rigged such that the potential free fall is never greater than six
feet. Restraint systems must be rigged such that there is no
possible vertical free fall.
Fall distance for shock absorbing lanyards
ENGLISH
Page 6
HAND GRIP ANCHOR
1/2 ft.
USER INSTRUCTIONS
Fall distance for self-retracting lifeline
Self Retracting
Lifeline
Working Level
Lower Level or Obstruction
3. FALL ARREST FORCES: The assembled fall arrest system
must keep fall arrest forces below 1,800 lbs. when used with a
full body harness. Do not use a body belt for fall arrest.
4. SWING FALLS: Swing falls
occur when the anchor is
not directly above the point
where a fall occurs. The
force of striking an object
while swinging can be great
and cause serious injury.
Minimize swing falls by
working as directly below
the anchorage as possible.
5. FALL CLEARANCE: Make certain enough clearance exists
in your fall path to prevent striking an object. The amount of
clearance needed is dependent upon the type of connecting
subsystem used and anchorage location. These anchorage
connectors can stretch up to 6” during a fall.
6. SHARP EDGES: Avoid working where parts of the system will
be in contact with, or abrade against, unprotected sharp edges.
7. RESCUE: Should a fall occur, the user (employer) must have a
rescue plan. If a worker falls and is forced to remain suspended
for any length of time, physical damage to the body or even
death can result. For this reason Werner, OSHA, ANSI and
most local regulations require that a rescue plan and the means
to implement the rescue plan are in place before use of this
equipment.
Anchorage Stretch
Bottom of Retractable Lifeline
2 ft.
Maximum Free Fall
2.5 ft.
Maximum Deceleration
1 ft. Harness Stretch
5 ft.
To Worker’s Back D-Ring
2 ft.
Safety Factor
Maximum Arrest
Distance (per ANSI)
4.5 ft.
Anchorages
CorrectIncorrect
Total Estimated
Fall Distance
13 ft.
SWING FALL
HAZARD
ENGLISH
Page 7
8. AFTER A FALL: Any equipment which has been subjected
to the force of arresting a fall must be removed from service
immediately.
Warning:
Never connect more than one personal fall arrest or restraint system
to this device.
Warning:
Follow manufacturer’s instructions for associated equipment used in
your fall protection or restraint system.
d. Training
OSHA, ANSI, and most local ordinances require that workers using
this product receive adequate training before use of this product.
These instructions and their entire contents should be a part of that
training.
II. Hand Grip Installation and Use
Warning:
Do not alter or intentionally misuse this equipment. Consult with
Werner Co. if using this equipment with components or subsystems
other than those described in this manual. Some subsystem and
component combinations may interfere with the operation of this
equipment. Use caution when using this equipment around moving
machinery, electrical hazards, chemical hazards, and sharp edges.
Warning:
Do not use this device if you are unable to tolerate the impact of
a fall arrest. Age and tness can seriously affect your ability to
withstand a fall. Pregnant women and minors must not use this
equipment.
a. Making Connections
1. Only use self-locking snap hooks and carabiners with this
equipment. Only use connectors that are suitable to each
application. Ensure all connections are compatible in size, shape
and strength. Do not use equipment that is not compatible.
Ensure all connectors are fully closed and locked.
ENGLISH
Page 8
HAND GRIP ANCHOR
USER INSTRUCTIONS
2. Werner Co. connectors
(snap hooks and carabiners)
PROPER CONNECTION
are designed to be used only
as specied in each product’s
user’s instructions. See
inappropriate connections.
INAPPROPRIATE CONNECTIONS
A. B.
NO! NO! NO! NO!
D. E. F.
Werner Co. snap hooks and carabiners should NOT be
connected:
i. to a D-ring to which another connector is attached.
ii. in a manner that would result in a load on the gate. If the
connecting element that a snaphook or carabiner attaches
to is undersized or irregular in shape, a situation could occur
where the connecting element applies a force to the gate of
the snaphook or carabiner. This force may cause the gate
(of either a self-locking or a non-locking snaphook) to open,
allowing the snaphook or carabiner to disengage from the
connecting point.
NOTE: Large throat opening snap hooks should not be
connected to standard size D-rings or similar objects which
will result in a load on the gate if the hook or D-ring twists
or rotates. Large throat snap hooks are designed for use on
xed structural elements such as rebar or cross members
that are not shaped in a way that can capture the gate of
the hook.
C.
NO!NO!NO!NO!
Page 9
ENGLISH
b. Anchorage Strength
ENGLISH
iii. in a false engagement, where features that protrude from
the snap hook or carabiner catch on the anchor and without
visual conrmation seems to be fully engaged to the anchor
point.
iv. to each other.
v. directly to webbing or rope lanyard or tie-back (unless
the manufacturer’s instructions for both the lanyard and
connector specically allow such a connection).
vi. to any object which is shaped or dimensioned such that the
snap hook or carabiner will not close and lock, or that roll-
out could occur.
3. Do not pass the lanyard or lifeline through the hand grip and
hook back into the lanyard or lifeline. When connecting, make
sure the connections are fully closed and locked.
4. When using an energy-absorbing lanyard, connect the energy
absorber “pack” end to the harness.
Depending on the application, the anchorage to which the hand
grip is installed must meet strengths as given below:
1. FALL ARREST: Anchorages selected for personal fall arrest
systems (PFAS) shall have a strength capable of sustaining
static loads, applied in the directions permitted by the PFAS, of
at least; (A) 3,600 lbs. (16kN) when certication exists (see ANSI
Z359.1 for certication denition), or (B) 5,000 lbs. (22kN) in the
absence of certication. When more than one PFAS is attached
to an anchorage, the anchorage strengths set forth in (A) and
(B) above shall be multiplied by the number of personal fall
arrest systems attached to the anchorage. Per OSHA 1926.500
and 1910.66; Anchorages used for attachment of PFAS shall
be independent of any anchorage being used to support or
suspend platforms, and capable of supporting at least 5,000 lbs.
(22kN) per user attached, or be designed, installed, and used as
part of a complete PFAS which maintains a safety factory of at
least two, and is supervised by a qualied person.
2. RESTRAINT: Hand Grips installed for restraint applications
must be attached to an anchorage capable of sustaining a static
load of at least 3,000 lbs. applied in any direction permitted by
the restraint system when in use.
Page 10
Loading...