Page 1
Assembly Instructions
Select Lab Adjustable Height
Workstation
Mobile version is shown.
Also available without casters.
Contents
Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Required Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Hardware Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Workstation Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Visit the Music Lab Workstations web page at www.wengercorp.com.
Note: Please read and understand these instructions before starting the assembly.
Note: If you need additional information, contact Wenger Corporation using the information below.
©Wenger Corporation 2018 Printed in USA 2018-07 Part #225D098-02
Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448
Basic Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Mobile Version Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Non-Mobile Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Optional Rackmount Shelf Assembly . . . . . . . . . . . . . . . . . . . . . . 23
Questions? Call.....USA: (800) 4WENGER (493-6437) • Worldwide: +1-507-455-4100 • wengercorp.com
Page 2
Important User Information
General
Copyright © 2018 by Wenger Corporation
All rights reserved. No part of the contents of this manual may be reproduced, copied, or transmitted in any form
or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information
storage and retrieval systems without the written permission of the publisher, unless it is for the purchaser’s
personal use.
Printed and bound in the United States of America.
The information in this manual is subject to change without notice and does not represent a commitment on the
part of Wenger Corporation. Wenger Corporation does not assume any responsibility for any errors that may
appear in these instructions.
In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for direct,
indirect, special, incidental, or consequential damages resulting from the use or defect of these instructions.
The manufacturer reserves the right to change this product at any time.
The information in this document is not intended to cover all possible conditions and situations that might occur.
The end user must exercise caution and common sense when assembling or installing Wenger Corporation
products. If any questions or problems arise, call the Wenger Corporation at (800) 4WENGER (493-6437)
or +1-507-455-4100 worldwide.
Manufacturer
The Select Lab Adjustable Height Workstation is manufactured by:
Wenger Corporation
555 Park Drive
Owatonna, MN 55060
(800) 4WENGER (493-6437) • +1 (507) 455-4100
wengercorp.com
Intended Use
· This product is intended for indoor use in normal ambient temperature and humidity conditions —
it must not be exposed to prolonged outside weather conditions.
· This product is intended to be assembled and used only as described in these instructions.
Warranty
This product is guaranteed free of defects in materials and workmanship for ten full years from date
of shipment. A full warranty statement is available upon request.
Optional power strips, digital locks and other electronic equipment are covered by the
individual manufacturer’s warranty.
2
Page 3
Safety Precautions
Throughoutthismanualyoumayndcautionsandwarningswhicharedenedasfollows:
• WARNING means that failure to follow the instruction may result in serious injury or death.
• CAUTION means that failure to follow the instruction may result in serious injury or damage
to property.
Read all of these safety instructions before assembling the Select Lab Adjustable Height Workstation.
!
CAUTION
Make sure anyone
assembling the Select
Lab Workstation has read
and understands these
instructions.
Required Tools
· Phillips Head Screwdriver
· Rubber or Plastic Mallet
· 3/8” Open-End Wrench or Socket
· Drill
!
CAUTION
Failure to comply with
Warnings and Cautions in
this document can result
in damage to property or
serious injury.
· Side Cutter or Scissors
· 5/32” Hex Insert Bit (supplied)
· 1-3/4” Caster Wrench (supplied)
!
CAUTION
To avoid damage and injury,
more than one person is
needed for assembly.
3
Page 4
Hardware Parts List
1
2
3
4
5
6
250A508._
7 x 50mm
Particle Board Screw
(color matched paint)
7
X003074
Flush Mount
Handle
12
X003110
1/4-20
Wing Nut
1/4 x 47/64”
Flat Washer
X003583
2-3/8” Grommet
X000824
#8-18 x 3/8”
Sheet Metal Screw
13
X001442
8
1-1/2” Plug
X001484
X003706
2” 5-Knuckle
Hinge
X003600
Wiring Clamp
14
3.75 Dia x 2.50
9
X003736
Clevis Pin
X000045
#8 x 5/8”
Pan Head Screw
10
X001503
#10-16 x 3/4”
Sheet Metal Screw
15
X002540
8 x 25mm
Wood Dowel
11
X002971
1/4-20 x 1/2”
Carriage Bolt
100A534
1-3/4” Caster Wrench
100A444
Corner
Bracket
16
17
X000482
#8 x 5/8
Sheet Metal Screw
(used only on mobile version)
23
250A515._
1/4-20
Cap Nut
(color matched paint)
X002998
4” Nylon Tie
(black paint)
27
18
225D234
Door Stop
Bracket
24
250A515
1/4-20
Cap Nut
250A508
7 x 50mm
Particle Board Screw
(black paint)
1/4-20 x 0.708”
Machine Screw
28
X003456
Push-In
Bumper
X003743
19
Flat Head Screw
25
(used only on mobile version)
20
X003738
#6 x 3/4”
X001162
#8 x 1-1/4”
Sheet Metal Screw
*Quantities may vary, extras can be discarded.
X001962
5/32” Hex
Insert Bit
26
21
22
X003751
8-32
Hex Nut
4
Page 5
Workstation Components
Item Description Item Description
29 Shelf Wiring Panel 39 Standard Swivel Caster
30 Front Wiring Panel 40 Adjustable Keyboard Bracket
31 Back Panel 41 Bottom Fixed Shelf
32 Left Side Panel 42 Wiring Access Door
33 Right Side Panel 43 Stiener
34 Desktop 44 Pullout Panel
35 Left Side Support Weldment 45 Headphone Mount
36 Right Side Support Weldment 46 Plain Channel*
37 Mobile Leg Tube 47 Non-Mobile Leg Tube*
38 Swivel Caster with Brake
42
30
29
34
36
33
31
32
35
43
45
40
46
44
41
37
39
38
47
*Used on
Non-Mobile Versions
Only
5
Page 6
Basic Assembly
The following assembly procedure shows the Mobile Version of the Adjustable
Height Workstation, the procedure is the same for the Non-Mobile Version unless
otherwise noted.
1. Connect the Shelf Wiring Panel (29) and Front Wiring Panel (30)
together using six Wood Dowels (5) and
veBlack 7 x 50mm Particle Board Screws (28).
Shelf Wiring
Panel
(29)
Wood Dowel
(5)
Front Wiring
Panel
(30)
Black
7 x 50mm
Particle Board Screw
(28)
2. Attach the Shelf Wiring Panel to the Back Panel (31)
usingveWoodDowels(5)and
four 7 x 50mm Particle Board Screws (1).
Wood Dowel
(5)
Back Panel
(31)
7 x 50mm
Particle Board Screw
(1)
6
Page 7
Basic Assembly (continued)
3. Attach four Wiring Clamps (9) to the Back Panel using four
#10-16 x 3/4” Sheet Metal Screws (10).
#10-16 x 3/4”
Sheet Metal Screw
Wiring Clamp
(9)
4. Attach two sets of 5-Knuckle Hinges (3) to the Back Panel using two
#6 x 3/4” Flat Head Screws (20).
Only one set of hinges will be attached if an optional Rackmount Shelf Accessory
will be installed.
Be sure that the screws are seated ush with the hinges.
(10)
#6 x 3/4”
Flat Head Screw
(20)
5-Knuckle
Hinge
(3)
This set of hinges will not be attached
if a Rackmount Accessory will be
installed.
7
Page 8
Basic Assembly (continued)
5. Insert eight color matched 1/4-20 Cap Nuts (23) into the outside surface
of both the Left Side Panel (32) and Right Side Panel (33).
The outside of the Side Panels do not have dowel holes.
Left
Side Panel
(32)
Color Matched
1/4-20
Cap Nuts
(23)
Right
Side Panel
(33)
Dowel holes are in the
inside of the Side Panels.
6. With the top facing up (the side without dowel holes), attach two sets of Door Stop Brackets (18)
to the back side of the Desktop (34) using two #8 x 5/8” Sheet Metal Screws (17) in each.
Only one set of brackets will be attached if anoptional Rackmount Shelf Accessory
will be installed.
7. Push/pull a Push-In Bumper (19) into each Door Stop Bracket.
Use two Bumpers where there will be adjoining Wiring Access Doors
Desktop
(34)
Trimotheexcesstailsusingasidecutterorscissors.
This set of brackets will not be
attached if a Rackmount Accessory will
be installed.
Dowel holes face down.
Push-In Bumper
Sheet Metal
Door Stop
Bracket
(18)
(19)
#8 x 5/8”
Screw
(17)
8
Page 9
Basic Assembly (continued)
8. Attach the Front Wiring Panel and Back Panel Assembly to the Right Side Panel (33)
usingthreeWoodDowels(5)andve7x50mmParticleBoardScrews(1).
Leave the Particle Board Screws loose until after Step #9.
Right Side
Panel
(33)
7 x 50mm
Particle Board Screw
(1)
These two screws may need to
be removed to complete Step #9.
Wood Dowel
(5)
9. Use more than one person to attach the Desktop to the Front Wiring Panel and
Right Side Panel using seven Wood Dowels (5) and three 7 x 50mm Particle Board Screws (1).
Wood Dowel
(5)
Tighten the
Particle Board Screws.
7 x 50mm
!
CAUTION
Particle Board Screw
(1)
To avoid damage and injury,
more than one person is
needed for assembly.
10. Tighten the Particle Board Screws installed in Step #8.
9
Desktop
Page 10
Basic Assembly (continued)
11. Attach the Left Side Panel to the Desktop, Back Panel and Front Wiring Panel using
six Wood Dowels (5) and eight 7 x 50mm Particle Board Screws (1).
Left
Side Panel
(32)
7 x 50mm
Particle Board Screw
(1)
12. Attach the Left and Right Side Support Weldments
to the Back Panel using
three #8 x 5/8” Sheet Metal Screws (17)
in each.
Left Side
Support Weldment
Wood Dowel
(5)
Right Side
Support Weldment
#8 x 5/8”
Sheet Metal Screw
(17)
10
Page 11
Mobile Version Assembly
The following assembly procedure shows how to assemble the Mobile Version
of the Adjustable Height Workstation.
For Non-Mobile Version Assembly, go to page 14.
1. Attach the Left Side Support Weldment (35) and
the Right Side Support Weldment (36) to the
Back Panel using three
#8 x 5/8” Sheet Metal Screws (17) in each.
Left Side
Support Weldment
(35)
Right Side
Support Weldment
(36)
2. Attach the Left and Right Side Support Weldments
to the bottoms of the Side Panels Back Panel
using four #8 x 1-1/4” Sheet Metal Screws (26)
in each.
3. Attach both Side Support Weldments
to each Side Panel using
one #8 x 5/8” Sheet Metal Screw (17).
#8 x 1-1/4”
Sheet Metal Screw
(26)
#8 x 5/8”
Sheet Metal Screw
(17)
#8 x 5/8”
Sheet Metal Screw
(17)
11
Page 12
Mobile Version Assembly (continued)
4. Attach the Left and Right Side Support Weldments
to the Nut Inserts in the Side Panels using
eight 1/4-20 x 0.708” Machine Screws (25)
in each.
1/4-20 x 0.708
Machine Screw
(25)
5. Attach six Wiring Clamps (9) to the
Back Panel using six
#10-16 x 3/4” Sheet Metal Screws (10).
#10-16 x 3/4”
Sheet Metal Screw
(10)
Wiring Clamp
(9)
6. Using a mallet, tap 1-1/4” Plug (14) into the open end of
all four Mobile Leg Tubes (37).
1-1/2” Plug
(14)
Mobile
Leg Tube
(37)
12
Page 13
Mobile Version Assembly (continued)
7. Insert one Adjustable Leg Assembly with the Plug end
at the top through the bottom of all four of the
Side Support Weldment slots.
Adjustable
Leg Assembly
8. Attach the two Swivel Casters with Brakes to
the front of the Workstation and two
Standard Swivel Casters to the
Fixed Tubes using the supplied
Caster Wrench (16).
Swivel Caster
with Brake
(38)
Standard Swivel
Caster
(39)
3.75 Dia x 2.50
Clevis Pin
(15)
9. Set the height of the Adjustable Leg Tubes with a
3.75 Dia x 2.50 Clevis Pin (15). and skip ahead to “Final Assembly” on Page 16.
13
Page 14
Non-Mobile Version Assembly
The following assembly procedure shows how to assemble the Non-Mobile Version
of the Adjustable Height Workstation.
For Mobile Version Assembly, go to page 11.
1. Attach six Wiring Clamps (9) to the
Back Panel using six
#10-16 x 3/4” Sheet Metal Screws (10).
#10-16 x 3/4”
Sheet Metal Screw
(10)
Wiring Clamp
(9)
2. Attach two Plain Channels (46) to the
Nut Inserts in both Side Panels using
four 1/4-20 x 0.708” Machine Screws (25)
in each.
Plain Channel
(46)
1/4-20 x 0.708”
Machine Screw
(25)
14
Page 15
Non-Mobile Version Assembly (continued)
3. Using a mallet, tap a 1-1/4” Plug (14) into both open ends
of all four Mobile Leg Tubes (47).
Non-Mobile
Leg Tube
(47)
1-1/2” Plug
(14)
4. Insert one Adjustable Leg Assembly with the Plug end
at the top through the bottom of all four of the
Plain Channel slots.
3.75 Dia x 2.50
Clevis Pin
(15)
Adjustable
Leg Assembly
5. Set the height of the Adjustable Leg Tubes with a
3.75 Dia x 2.50 Clevis Pin (15). and skip ahead to “Final Assembly” on Page 16.
15
Page 16
Final Assembly
The following assembly procedure shows the Mobile Version of the Adjustable
Height Workstation, the procedure is the same for the Non-Mobile Version unless
otherwise noted.
1. Attach seven Corner Brackets (6) to the Desktop,
Side Panels and Front Wiring Panel using
#8 x 5/8” Pan Head Screws (4) in each.
#8 x 5/8”
Pan Head Screw
(4)
Corner
Bracket
(6)
2. Attach two Adjustable Keyboard Brackets (40)
tothebottomoftheDesktopusingve
#10-16 x 3/4” Sheet Metal Screws (10)
in each.
#10-16 x 3/4”
Sheet Metal Screw
(10)
Adjustable
Keyboard
Bracket
(40)
16
Page 17
Final Assembly (continued)
3. This step is for the Mobile Version Only, does not apply to the Non-Mobile Version:
Insert four Black 1/4-20 Cap Nuts (24) into pilot holes in the the top of the
Bottom Fixed Shelf (41).
Black
1/4-20
Cap Nut
(24)
Bottom
Fixed Shelf
(41)
4. Tip the Assembly onto the Legs.
17
Page 18
Final Assembly (continued)
5. Attach the Bottom Fixed Shelf (41).
Mobile Version Instruction (Non-Mobile Version on the following page):
a. Keep the narrower side of the Bottom Shelf at the same side as the Keyboard Brackets
(this leaves room for a computer tower on the wider side of the shelf).
b. WiththeCapNutsfacingup,tiptheShelftotontothebottomlipsofthe
Side Support Weldments.
c. Attach the Shelf to the Side and Back Panels using two Wood Dowels (5)
at the back and eleven 7 x 50mm Particle Board Screws (1).
Bottom
7 x 50mm
Particle Board Screw
(1)
Lip
Wood Dowel
(5)
1/4-20
Cap Nut
Narrower side
Bottom Fixed
Shelf
(41)
Wider side
d. Attach the Shelf to the Side Support Weldments on each side using
two 1/4-20 x 0.708” Machine Screws (25) into the previously installed Cap Nuts.
1/4-20
Cap Nut
1/4-20 x 0.708”
Machine Screw
(25)
18
Page 19
Final Assembly (continued)
5. Attach the Bottom Fixed Shelf (41).
Non-Mobile Version Instruction (Mobile Version on the previous page):
a. Tip the Assembly onto the Back Panel.
b. Keep the narrower side of the Bottom Shelf
at the same side as the Keyboard Brackets
(this leaves room for a computer
tower on the wider side of the shelf).
c. TiptheShelftotoverthePlainChannels.
d. Attach the Shelf to the Side and
Back Panels using two
Wood Dowels (5) at the back and
six 7 x 50mm Particle Board Screws (1).
7 x 50mm
Particle Board Screw
(1)
Wood Dowel
(5)
Narrower side
Wider side
Bottom Fixed
Shelf
(41)
e. Tip the Assembly onto the Legs.
f. Attach the Shelf to the Back Panel on
each side using three
7 x 50mm Particle Board Screws (1)
into each Side Panel.
7 x 50mm
Particle Board Screw
(1)
19
Page 20
Final Assembly (continued)
6. Attach the Flush Mount Handle (7) to the longer Wiring Access Door (42)
using two #8-18 x 3/8” Sheet Metal Screws (8).
Sheet Metal Screw
Flush Mount
7. Attach a Wiring Access Door to each set of Hinges in the Back Panel using
two #6 x 3/4” Flat Head Screws (20).
Be sure that the screws are seated ush with the hinges.
#8-18 x 3/8”
(8)
Handle
(7)
Wiring Access
Door
(42)
5-Knuckle
#6 x 3/4”
Flat Head Screw
(20)
Hinge
(3)
Wiring Access
Door
(42)
20
Page 21
Final Assembly (continued)
8.AttachaStiener(43)tothebottomonthebacksideofthePulloutPanel(44)
using three #8 x 5/8” Sheet Metal Screws (17).
Sheet Metal Screw
Holes can be used to secure
keyboard cables with the
included 4”Nylon Ties (27).
Pullout Panel
(44)
Back side is
unnished
#8 x 5/8”
(17)
Front side has
edge banding
Stiener
(43)
9. Extend the Drawer Glides and attach one to each side of the Pullout Panel using the
included fasteners at all four locations.
10. Attach the Adjustable Keyboard Bottom Brackets to the Drawer Glides using
a #8-32 x 3/8” Self Tapping Screw (included with drawer glides) and
a 8-32 Hex Nut (22) on each side.
#8-18 x 3/8”
Adjustable
Keyboard Bottom
Bracket
Use the included fasteners
at all four locations
Drawer
Glide
Sheet Metal Screw
(included with drawer glides)
8-32
Hex Nut
(22)
21
Page 22
Final Assembly (continued)
11. Fit the back of both Drawer Glides into the slots of the Front Wiring Panel.
Attach the Pullout Drawer to the
Adjustable Keyboard Brackets using
one 1/4-20 x 1/2” Carriage Bolt (11),
1/4 x 47/64” Flat Washer (13)
and 1/4-20 Wing Nut (12)
on each side.
1/4-20
Wing Nut
(12)
1/4 x 47/64
Flat Washer
(13)
It is preferred to face the smooth head of the Carriage Bolt
toward the inside as shown.
If space is limited, the Wing Nut and Washer can face
the inside but there may be an issue with snagging.
1/4-20 x 1/2”
Carriage Bolt
(11)
Fit Drawer Glides
into slots
Desktop is shown
removed for clarity.
12. Attach Headphone Mount (45) to the bottom of the Pullout Drawer
using three #10-16 x 3/4” Sheet Metal Screws (10).
Headphone Mount can also be attached to the inside of the Right Side Panel.
13. Insert Grommets (2) into the
Left, Right and Back Panels.
Headphone Mount
#10-16 x 3/4”
Sheet Metal Screw
(10)
Headphone
Mount
(45)
can also be mounted
to the inside of the
Right Side Panel.
Grommet
(2)
22
Page 23
Optional Rackmount Shelf Assembly
If installing the Optional Rackmount Shelf Assembly, the smaller Wiring Access Door and
Hinges must be removed.
1. Clip the Cage Nuts into the front of each individual Rackmount Shelf.
10-32 x 3/4” Truss Screws are included to secure
electronic components into the Rackmount.
The deepest electronic components should be
installed at the bottom Rackmount Shelf.
2. Attach the Rackmount Shelf to the Desktop using six #8 x 5/8” Truss Head Screws.
If there are no existing pilot holes, a template must be used
for placement.
Rackmount
Shelf Unit
Cage
Nut
10-32 x 3/4”
Truss Screw
#8 x 5/8”
Truss Head Screw
3. Connect additional shelving units using six #10-32 x 3/8” Pan Head Screws
and 10-32 Jam Lock Nuts.
If there are no pilot holes,
a template must be used
for placement.
10-32 x 3/8”
Pan Head Screw
10-32 x 3/8”
Jam Lock Nut
23
Page 24
Optional Rackmount Shelf Assembly (continued)
4. Attach two 5-Knuckle Hinges to the top Rackmount Shelf
using two #8-32 x 1/2” Flat Head Screws and
two #8-32 Nylon Lock Nuts in each.
Be sure that the screws are seated ush with
the hinges.
5. Push/pull two Push-In Bumpers into the front
of the Rackmount.
Trimotheexcesstailsusingasidecutter
or scissors.
6. Clip the two Cage Nuts into the top at the
front of the Top Rackmount Shelf.
7. Attach the Top Panel to the Hinges using two
#6 x 3/4” Flat Head Screws in each Hinge.
Be sure that the screws are seated ush with
the hinges.
5-Knuckle
Hinge
#8-32 x 1/2”
Flat Head Screw
Push-In
Bumper
#8-32
Nylon
Lock Nut
Cage
Nut
Top Panel
#6 x 3/4”
Flat Head Screw
8. Close the Top Panel and secure it to the top Rackmount Shelf
using two #10-32 x 1.25” Pan Head Screws.
24
#10-32 x 1.25”
Pan Head Screw
Loading...