Page 1
©Wenger Corporation 2009 Printed in China 011/09 Part #251A150-01
Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448
Questions? Call.....USA: (800) 733-0393 • International (call collect): (507) 455-4100 • www.wengercorp.com
CONTENTS
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Important User Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Manufacturer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Parts and Fastener List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
Please read and understand these Assembly Instructions before working with or using the Guitar
Mobile Storage Rack.
If you need additional information about the Guitar Mobile Storage Rack, contact Wenger
Corporation using the information below.
Assembly Instructions
Guitar Mobile Storage Rack
Page 2
2
SAFETY PRECAUTIONS
Make sure that anyone
working on the Guitar Mobile
Storage Rack has read and
understands this manual.
!
CA UTION
Failure to comply with
Warnings and Cautions in
this document can result in
damage to property or
serious injury.
!
CA UTION
Always observe and comply
with the Warnings and
Cautions posted on the
system equipment.
!
CA UTION
This manual contains cautions which are defined as follows.
• CAUTION; failure to follow the instruction may result in serious injury or damage to property.
Read all of these safety instructions before assembling the Guitar Mobile Storage Rack.
The Guitar Mobile Storage Rack is guaranteed free of defects in materials and workmanship for five full
years.
Our guarantee assures you of either a full refund or repair or replacement of the defective materials or
workmanship without charge, at the discretion of our Customer Service Department. Just call a
Customer Service Representative at 1-800-887-7145 and state the reason you are dissatisfied. If a
product return is necessary, your representative will issue a return authorization. This is your sole
remedy for breach of this warranty.
Should you have a question or problem with any Wenger product, don’t hesitate to call, even if the
product is past warranty. It’s important to us that all our customers be satisfied.
This is the sole warranty made by Wenger. Wenger disclaims all other warranties, including the
warranties of merchantability and fitness for a particular purpose, as well as all liability for incidental,
consequential, special, and indirect damage. Wenger liability for direct damages shall be limited to the
amount you paid for the product involved. Wenger reserves the right to make product changes without
obligation to incorporate such changes into products previously sold.
Some states do not allow the exclusion or limitation of damages or warranties, so the above may not
apply to you. This warranty gives you specific legal rights. You may also have other rights which vary
from state to state.
WARRANTY
OPERATION
Lock casters when the rack is in the desired position. Unlock casters to move the rack. If the instruments are
left on the rack when moved, two people are required to move the rack. Move the rack slowly and carefully
with two to four people holding the instruments securely keeping them in the yokes and avoiding them from
hitting each other.
Page 3
3
IMPORTANT USER INFORMATION
GENERAL
Copyright © 2009 by Wenger Corporation
All rights reserved. No part of the contents of this manual may be reproduced, copied, or transmitted in
any form or by any means including graphic, electronic, or mechanical methods or photocopying,
recording, or information storage and retrieval systems without the written permission of the publisher,
unless it is for the purchaser's personal use.
The information in this manual is subject to change without notice and does not represent a commitment
on the part of Wenger Corporation. Wenger Corporation does not assume any responsibility for any
errors that may appear in this manual.
In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for
direct, indirect, special, incidental, or consequential damages resulting from the use or defect of this
manual.
The information in this document is not intended to cover all possible conditions and situations that might
occur. The end user must exercise caution and common sense when assembling or installing Wenger
Corporation products. If any questions or problems arise, call Wenger Corporation at 1-800-733-0393.
MANUFACTURER
The Guitar Mobile Storage Racks are manufactured for:
Wenger Corporation
555 Park Drive
Owatonna, MN 55060
1-507-455-4100 • 1-800-733-0393
www.wengercorp.com
INTENDED USE
• This product is intended for indoor use in normal ambient temperature and humidity conditions - it
must not be exposed to prolonged outside weather conditions.
• This product is intended to be assembled only as described in these instructions.
Page 4
4
• Remove components from packaging carefully.
• Keep hardware together until needed for assembly.
• It is recommended that two people are used in the assembly process.
BEFORE ASSEMBLY
Item Qty. Description Item Qty. Description
1 2 End Panel 11 24 Cross Dowel, 1/4-20
2 4 Lower Cross Panel 12 2 Swivel Caster with Brake
3 4 Stiffener 13 14 Machine Screw, 1/4-20 x 3.15
4 2 Caster Panel 14 34 Washer, 1/4 x 5/8 OD
5 2 Yoke Stiffener 15 22 Wing Nut, 1/4-20
6 4 Male Extrusion 16 42 Hex Socket Lag Screw
7 4 Female Extrusion with Pad 17 12 Machine Screw, 1/4 x 4.63
8 2 Yoke Mount Panel 18 20 Machine Screw, 1/4 x 2.359
9 20 Yoke 19 1 Allen Wrench, 5/32" L-Handle
10 2 Swivel Caster without Brake or 5/32" Hex Insert Bit
The following tools are required to assemble a Guitar Mobile Storage Rack.
• Phillips Screwdriver #2
•
5
/32" Allen Wrench (provided)
• Straight Blade Screwdriver
REQUIRED TOOLS
PARTS AND FASTENER LIST
1
2
3
4
5
6
7
8
9
10
11
12
18
14
15 16
*Note: Extra fasteners may remain after completion of the assembly and can be discarded.
17
13
Page 5
5
To begin the assembly of the Guitar Mobile Storage Rack:
1. Remove the four Lower Cross Panels (#2), four Stiffeners (#3), two Yoke Stiffeners (#5), two Yoke
Mount Panels (#8) and the hardware pack from the package.
2. On a level surface with free access along one side, stand the Lower Cross Panel (#2) upright as
shown with the smaller through holes along the lower edge. (see figure A)
3. Lay the Stiffener (#3) flat on the level surface with the 3mm pilot holes facing the Lower Cross Panel
(#2). (see figure A)
4. The pilot holes on the stiffener and the through holes on the lower edge of the Lower Cross Panel
should line up. Bring them into contact and align the sides of the Lower Cross Panel and the
Stiffener so that they are flush. Insert the Hex Socket Lag Screw (#16) into each through hole in the
support member and carefully drive the Hex Socket Lag Screw into the stiffener until it secures the
two pieces together. (see figure A)
Note: Hold the two pieces together firmly until at least three screws are installed, preferably one near
each end and one in the center. Some screws may require more effort to drive than others,
depending on the density of the wood. Use caution not to strip out of the Hex Socket Lag
Screw head while driving the screw as this may cause injury or damage. The screws must be
driven in straight and on the centerline of the stiffener to properly align the components and to
prevent damage to the stiffener. Screws should be driven into the cross-member until flush.
5. Repeat steps 2 through 4 until all four Lower Cross Panel/Stiffener assemblies are complete.
ASSEMBLY
figure A
2
3
16
figure B
6. Repeat steps 2 through 4 to the assemble the two Yoke Mount Panel (#8) and Yoke Stiffener (#5).
Note: The holes on the Yoke Stiffener (#5) are off set. Two people are recommended to complete
this step. One person is needed to hold the pieces tightly together while the other person
secures them using the Hex Socket Lag Screws (#16). (see figure B)
16
5
8
Page 6
6
7. Insert the Cross Dowels (#11) into the three cross holes in one of the Cross Panel/Stiffener
assemblies. There are three holes on each end of the assembly as shown in figure C.
Note: The slot in the metal cross dowel indicates the through hole for the machine screw and should
be aligned with a screwdriver to assist starting the threads of the machine screw by hand.
8. Using Machine Screws, 1/4-20 x 4.63 (#17) and washers, 1/4 x 5/8 OD (#14), assemble one End
Panel (#1), one Caster Panel (#4) and one side of the Cross Panel/Stiffener assembly as shown.
(see figure C)
Note: Do not tighten snugly until step 9 is complete.
9. Repeat step 8 for the second Cross Panel/Stiffener assembly.
10. Secure the end of the Caster Panel (#4) to the End Panel (#1) using Machine Screw, 1/4-20 x 3.15
(#13), Washer, 1/4 x 5/8 OD (#14) and Wing Nut, 1/4-20 (#15). (see figure D)
11. Repeat steps 7 through 10 on the opposite end of the Cross Panel/Stiffener assembly.
ASSEMBLY CONTINUED
11
17
4
1
2
17
13
4
1
13
4
1
14
15
Cross Panel/Stiffener Assembly
3
figure C
figure D
1
14
14
Page 7
12. To assemble the remainder Cross Panel/Stiffener assemblies to the rack;
a. Repeat step 7.
b. Using Machine Screws 1/4-20 x 3.15 (#13), assemble the other Cross Panel/Stiffener assembly
to the End Panels (#1) shown. (see figure E)
13. To assemble the Yoke Mount Panel/Yoke Stiffener assemblies to the rack;
a. Using Hex Socket Lag Screws (#16), assemble the other Yoke Mount Panel/Yoke
Stiffener assembly to the End Panels (#1) shown. (see figure F)
7
ASSEMBLY CONTINUED
Cross Panel/Stiffener Assembly
Yoke Mount Panel/
Yoke Stiffener Assembly
13
16
1
1
1
1
figure E
figure F
Page 8
14. Clear the area behind the Guitar Mobile Rack and place corrugation, cloth or carpet down for protection.
15. With a minimum of two people, gently tip the Guitar Mobile Rack onto it’s back.
16. Install the two Swivel Casters with the Brake (#12) carefully into the sockets in the bottom of the Caster
Panel (#4) on the front side of the Guitar Mobile Rack.
(see figure G)
17. Install the two Swivel Casters without the Brake (#10) carefully into the sockets in the bottom of the
Caster Panel (#4) on the back side of the Guitar Mobile Rack.
(see figure G)
18. Set the Guitar Mobile Rack upright onto it’s casters.
19. Remove the yokes (#9) from the package and install them onto the
Yoke Mount Panel/Yoke Stiffener
assemblies, using machine screws (#18), washers (#14) and the wing nuts (#15). Wing nuts are
assembled at the top of the Yokes mounted on the top
Yoke Mount Panel/Yoke Stiffener and on the
bottom of the Yokes mounted on the bottom
Yoke Mount Panel/Yoke Stiffener. (see figure H)
Note: Some experimentation may be required to find the most secure and convenient position of the
instrument in the yokes. You may attach the yokes on the bottom side of the stiffeners for better fit.
Tighten all fasteners before using the Guitar Mobile Storage Rack and routinely check for secure
connections.
ASSEMBLY CONTINUED
8
4
12
10
4
15
14
9
18
18
9
14
15
figure G
figure H
Note:
If storing Guitars in their
cases, remove the
individual yokes as they
are not needed. Save
the yokes and hardware
for future use.
Loading...