Wenger Bravo Stand, Roughneck Stand, Classic 50 Stand, Preface Stand, Preface Conductor’s Stand Assembly And Owner's Manual

Assembly and Owner's Instructions

Music Stands

Bravo® Stand

Roughneck® Stand

Classic 50® Stand

Preface® Stand

Preface® Conductor’s Stand

Contents

Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

General .........................................2

Manufacturer .....................................2

Intended Use .....................................2

Warranty ........................................2

Required Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Visit the Music Stands web page at wengercorp.com for more information.

Note: Please read and understand these instructions before assembling or using.
Note: If you need additional information, contact Wenger Corporation using the information below.

©Wenger Corporation 2018 Printed in USA 2018-07 Part #237A113-11

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Base and Slider Assembly ..........................4

Desk and Slider Assembly ..........................5

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448

Questions? Call.....USA: (800) 4WENGER (493-6437) • Worldwide: [phone] • wengercorp.com

Important User Information

General

Copyright © 2018 by Wenger Corporation

All rights reserved. No part of the contents of this manual may be reproduced, copied, or transmitted in any form
or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information
storage and retrieval systems without the written permission of the publisher, unless it is for the purchaser’s
personal use.

Printed and bound in the United States of America.

The information in this manual is subject to change without notice and does not represent a commitment on the
part of Wenger Corporation. Wenger Corporation does not assume any responsibility for any errors that may
appear in these instructions.

In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for direct,
indirect, special, incidental, or consequential damages resulting from the use or defect of these instructions.
The manufacturer reserves the right to change this product at any time.

The information in this document is not intended to cover all possible conditions and situations that might occur.
The end user must exercise caution and common sense when assembling or installing Wenger Corporation
products. If any questions or problems arise, call the Wenger Corporation at (800) 4WENGER (493-6437)
or [phone] worldwide.

Manufacturer

The Music Stands are manufactured by:

Wenger Corporation
555 Park Drive
Owatonna, MN 55060
(800) 4WENGER (493-6437) • [phone]
wengercorp.com

Intended Use

· This product is intended for indoor use in normal ambient temperature and humidity
conditions — it must not be exposed to prolonged outside weather conditions.

· This product is intended to be assembled only as described in these instructions.

Warranty

This product is guaranteed free of defects in materials and workmanship for ve full years from date
of shipment. A full warranty statement is available upon request.

2

Required Tools

The following tools are needed to assemble the Music Stands:

• Plastic or Wood Mallet

• 7/16” (11 mm) Box End or Socket Wrench

• 5/32” (4 mm) Hex Key Wrench

Parts List

!

CAUTION

Only use hand tools for assembly.
Power tools could damage the
components.

7

6

4

5

1

9

2

3

Trigger Lock is on

Roughneck Stand

ONLY

1

Item Qty Description Item Qty Description

1 1 Slider Assembly 6 1 Washer, 1/4” ID x 1” OD
2 1 Base Assembly 7 1 Lock Nut, Flange, BZ, 1/4-20”
3 1 Desk 8 1 Socket Screw, BHD, 1/4-20 x 1.25”
4 1 Pivot Hub 9 1 Bushing Insert (Roughneck and Preface Stands ONLY)

5 1 Elevator Bolt, 1/4-20 x 2” 10 1 Washer, 1/4” ID x 1” OD (Classic 50 Stand ONLY)

10

8

3