Wen 6515, 6515T User Manual
1" x 30" BELT SANDER
WITH 5" SANDING DISC
bit.ly/wenvideo
IMPORTANT:
Your new tool has been engineered and manufactured to WEN’s highest standards for dependability,
ease of operation, and operator safety. When properly cared for, this product will supply you years
of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings,
and cautions. If you use your tool properly and for its intended purpose, you will enjoy years of
safe, reliable service.
NEED HELP? CONTACT US!
Have product questions? Need technical support?
Please feel free to contact us at:
800-232-1195
(M-F 8AM-5PM CST)
techsupport@wenproducts.com
WENPRODUCTS.COM
TABLE OF CONTENTS
Technical Data
General Safety Rules
Specific Safety Rules For Belt/Disc Sander
Electrical Information
Know Your Belt/Disc Sander
Assembly and Adjustments
Operation
Maintenance
Exploded View and Parts List
Troubleshooting
Warranty
TECHNICAL DATA
Model Numbers:
Motor:
No Load Disc Speed:
Disc Diameter:
No Load Belt Speed:
Belt Size:
Dust Port Size:
Dust Port Adapter:
Included Sanding Disc:
Included Sanding Belt:
Net Weight:
Product Dimensions:
2
3
4
5
6
7
10
11
12
14
15
6515, 6515T
120 V, 60 Hz, 2.3 A
3450 RPM
5 inches
3160 FPM
1 x 30 inches
1.5 inches
2 inches
80 Grit
100 Grit
16 lb
14 x 11.5 x 15.5 inches
2
GENERAL SAFETY RULES
Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFE-
TY INSTRUCTIONS.
WARNING: To avoid mistakes and serious injury, do not plug in your tool until the following steps
have been read and understood.
1. READ and become familiar with this entire instruction manual. LEARN the tool’s applications, limitations, and
possible hazards.
2. AVOID DANGEROUS CONDITIONS. Do not use power tools in wet or damp areas or expose them to rain.
Keep work areas well lit.
3. DO NOT use power tools in the presence of flammable liquids or gases.
4. ALWAYS keep your work area clean, uncluttered, and well lit. DO NOT work on floor surfaces that are slippery
with sawdust or wax.
5. KEEP BYSTANDERS AT A SAFE DISTANCE from the work area, especially when the tool is operating.
NEVER allow children or pets near the tool.
6. DO NOT FORCE THE TOOL to do a job for which it was not designed.
7. DRESS FOR SAFETY. Do not wear loose clothing, gloves, neckties, or jewelry (rings, watches, etc.) when operating the tool. Inappropriate clothing and items can get caught in moving parts and draw you in. ALWAYS wear
non-slip footwear and tie back long hair.
8. WEAR A FACE MASK OR DUST MASK to fight the dust produced by operations.
WARNING: Dust generated from certain materials can be hazardous to your health. Always operate the tool in a well-ventilated area and provide for proper dust removal. Use dust collection systems
whenever possible.
9. ALWAYS remove the power cord plug from the electrical outlet when making adjustments, changing parts,
cleaning, or working on the tool.
10. KEEP GUARDS IN PLACE AND IN WORKING ORDER.
11. AVOID ACCIDENTAL START-UPS. Make sure the power switch is in the OFF position before plugging in
the power cord.
12. REMOVE ADJUSTMENT TOOLS. Always make sure all adjustment tools are removed from the tool before
turning it on.
13. NEVER LEAVE A RUNNING TOOL UNATTENDED. Turn the power switch to OFF. Do not leave the
tool until it has come to a complete stop.
14. NEVER STAND ON A TOOL. Serious injury could result if the tool tips or is accidentally hit. DO NOT store
anything above or near the tool.
3
GENERAL SAFETY RULES
15. DO NOT OVERREACH. Keep proper footing and balance at all times. Wear oil-resistant rubber-soled footwear. Keep the floor clear of oil, scrap, and other debris.
16. MAINTAIN TOOLS PROPERLY. ALWAYS keep tools clean and in good working order. Follow instructions for lubricating and changing accessories.
17. CHECK FOR DAMAGED PARTS. Check for alignment of moving parts, jamming, breakage, improper
mounting, or any other conditions that may affect the tool’s operation. Any part that is damaged should be properly
repaired or replaced before use.
18. MAKE THE WORKSHOP CHILDPROOF. Use padlocks and master switches and ALWAYS remove starter keys.
19. DO NOT operate the tool if you are under the influence of drugs, alcohol, or medication that may affect your
ability to properly use the tool.
20. USE SAFETY GOGGLES AT ALL TIMES that comply with ANSI Z87.1. Normal safety glasses only have
impact resistant lenses and are not designed for safety. Wear a face or dust mask when working in a dusty environment. Use ear protection such as plugs or muffs during extended periods of operation.
SPECIFIC RULES FOR THE BELT SANDER
WARNING: Do not operate this tool until it is completely assembled and installed according to the
instructions.
1. This sander is designed to sand wood or wood-like products only. Sanding or grinding other materials could
result in fire, injury, or damage to the workpiece.
2. Use the sander on horizontal surfaces only. Operating the sander when mounted on non-horizontal surfaces may
result in motor damage or injury.
3. Make sure the sanding belt is installed in the correct direction. See directional arrow on back of belt.
4. Always have the tracking adjusted properly so the belt does not run off the pulleys.
5. Do not use sanding belts or discs that are damaged, torn, or loose. Use only correct size sanding belt and disc.
6. Always hold the workpiece firmly when sanding. Keep hands away from sanding belt or disc. Sand only one
workpiece at a time.
7. Always hold the workpiece firmly on the table when using the disc sander and when using the belt sander.
8. Always sand on the downward side of the sanding disc when using the disc sander. Sanding on the upward side
of the disc can cause the workpiece to fly out of position, resulting in injury.
9. Always maintain a minimum clearance of 1/16 inch (1.6 mm) or less between the table or backstop and the sanding belt or disc.
4
SPECIFIC RULES FOR THE BELT SANDER
10. Do not sand pieces of material that are too small to be safely supported.
11. When sanding a large workpiece, provide additional table height support.
12. Do not sand with the workpiece unsupported. Always support the workpiece with the table.
13. Always remove scrap pieces and other objects from the tables before turning the sander ON.
14. Never perform layout, assembly or set-up work on the table while the sander is operating.
15. Never use solvents to clean plastic parts. Solvents could dissolve or otherwise damage the material. Use only a
soft damp cloth to clean plastic parts.
16. Should any component of your sander be missing/damaged or fail in any way, shut off switch and remove plug
from power supply outlet. Replace the missing, damaged, or failed parts before resuming operation.
17. Never pull the power cord out of the receptacle. Keep cords away from heat, oil, and sharp edges.
18. Have an electrician replace or repair damaged or worn cords immediately.
ELECTRICAL INFORMATION
GROUNDING INSTRUCTIONS
IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides the path of least resistance
for an electric current and reduces the risk of electric shock. This tool is equipped with an electric cord that has an
equipment grounding conductor and a grounding plug. The plug MUST be plugged into a matching outlet that is
properly installed and grounded in accordance with ALL local codes and ordinances.
DO NOT MODIFY THE PLUG PROVIDED. If it will not fit the outlet, have the proper outlet installed by a
licensed electrician.
IMPROPER CONNECTION of the equipment grounding conductor can result in electric shock. The conductor with the green insulation (with or without yellow stripes) is the equipment grounding conductor. If repair or
replacement of the electric cord or plug is necessary, DO NOT connect the equipment grounding conductor to a
live terminal.
CHECK with a licensed electrician or service personnel if you do not completely understand the grounding instructions or whether the tool is properly grounded.
USE ONLY THREE-WIRE EXTENSION CORDS that have three-pronged
plugs and outlets that accept the tool’s plug as shown in Fig. A. Repair or replace a damaged or worn cord immediately.
Fig. A
CAUTION: In all cases, make certain the outlet in question is properly grounded. If you are not sure, have a licensed electrician check the outlet.
WARNING: This tool is for indoor use only. Do not expose to rain
or use in damp locations.
5
Loading...