Wells Manufacturing ut10 Service Manual
WELLS BLOOMFIELD, LLC
2 ERIK CIRCLE, P. O. Box 280 Verdi, NV 89439
telephone: 775-689-5703
fax: 775-689-5976
www.wellsbloomfield.com
OPERATION MANUAL
SELF-LEVELING
DROP-IN
DISPENSERS
for ROUND
DINNERWARE
UT Series
432
Model UT8
Model UTS8
UTS Series
UTH Series
&
UTY Series
Includes
Model UTH8
IMPORTANT: DO NOT DISCARD THIS MANUAL
This manual is considered to be part of the appliance and is to be given to the OWNER or
MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of
this appliance. Additional manuals are available from your WELLS DEALER.
THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS U S ING OR
INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any
questions concerning installation, operation or maintenance of this equipment.
INSTALLATION
USE & CARE
PRINTED IN UNITED STATES OF AMERICA
p/n 303848 Rev. B ECN-13378 M432 071030 cps
LIMITED WARRANTY STATEMENT
Unless otherwise specified, all commercial cooking
equipment manufactured by WELLS BLOOMFIELD, LLC is
warranted against defects in materials and workmanship for
a period of one year from the date of original installation or
18 months from the date of shipment from our factory,
whichever comes first, and is for the benefit of the original
purchaser only.
THIS WARRANTY IS THE COMPLETE AND ONLY
WARRANTY, EXPRESSED OR IMPLIED IN LAW OR IN
FACT, INCLUDING BUT NOT LIMITED TO, WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE, AND/OR FOR DIRECT,
INDIRECT OR CONSEQUENTIAL DAMAGES IN
CONNECTION WITH WELLS BLOOMFIELD PRODUCTS.
This warranty is void if it is determined that, upon inspection
by an authorized service agency, the equipment has been
modified, misused, misapplied, improperly installed, or
damaged in transit or by fire, flood or act of God. It also
does not apply if the serial nameplate has been removed, or
if service is performed by unauthorized personnel. The
prices charged by Wells Bloomfield for its products are
based upon the limitations in this warranty. Seller’s
obligation under this warranty is limited to the repair of
defects without charge by a Wells Bloomfield factory
authorized service agency or one of its sub-service
agencies. This service will be provided on customer’s
premises for non-portable models. Portable models (a
device with a cord and plug) must be taken or shipped to
the closest authorized service agency, transportation
charges prepaid, for service. In addition to restrictions
contained in this warranty, specific limitations are shown in
the Service Policy and Procedure Guide. Wells Bloomfield
authorized service agencies are located in principal cities.
This warranty is valid in the United States and Canada and
void elsewhere. Please consult your classified telephone
directory, your foodservice equipment dealer or contact:
Service Department, Wells Bloomfield, LLC
P.O. Box 280, Verdi, Nevada 89439
phone (775) 689-5707 or fax (775) 689-5976
for information and other details concerning warranty.
SERVICE POLICY AND PROCEDURE GUIDE and ADDITIONAL WARRANTY EXCLUSIONS
1. Resetting of safety thermostats, circuit breakers, over
load protectors, and/or fuse replacements are not
covered by this warranty unless warranted conditions
are the cause.
2. All problems due to operation at voltages or phase
other than specified on equipment nameplates are
not covered by this warranty.
Conversion to correct voltage and/or phase must be
the customer’s responsibility.
3. All problems due to electrical connections not made
in accordance with electrical code requirements
and wiring diagrams supplied with the equipment are
not covered by this warranty.
4. Replacement of items subject to normal wear, to
include such items as knobs, light bulbs; and, normal
maintenance functions including adjustments of
thermostats, adjustment of micro switches and
replacement of fuses and indicating lights are not
covered by warranty.
5. Damage to electrical cords and/or plug due to exposure
to excessive heat are not covered by this warranty.
6. Full use, care, and maintenance instructions supplied
with each machine. Noted maintenance and
preventative maintenance items, such as servicing and
cleaning schedules, are customer responsibility. Those
miscellaneous adjustments noted are customer
responsibility. Proper attention to preventative
maintenance and scheduled maintenance procedures
will prolong the life of the appliance.
7. Travel mileage is limited to sixty (60) miles from an
Authorized Service Agency or one of its sub-service
agencies.
8. All labor shall be performed during regular working
hours. Overtime premium will be charged to the buyer.
9. All genuine Wells replacement parts are warranted for
ninety (90) days from date of purchase on nonwarranty equipment. This parts warranty is limited only
to replacement of the defective part(s). Any use of
non-genuine Wells parts completely voids any
warranty.
10. Installation, labor, and job check-outs are not
considered warranty and are thus not covered by this
warranty.
11. Charges incurred by delays, waiting time or operating
restrictions that hinder the service technician’s ability to
perform service are not covered by warranty. This
includes institutional and correctional facilities.
432 p/n 303848 OpM Self-Levelling Round Dishware Dispenser
SHIPPING DAMAGE CLAIM PROCEDURE
NOTE: For your protection, please note that equipment in
this shipment was carefully inspected and packaged by
skilled personnel before leaving the factory. Upon
acceptance of this shipment, the transportation company
assumes full responsibility for its safe delivery.
IF SHIPMENT ARRIVES DAMAGED:
1. VISIBLE LOSS OR DAMAGE: Be certain that any
visible loss or damage is noted on the freight bill or
express receipt, and that the note of loss or damage is
signed by the delivery person.
2. FILE CLAIM FOR DAMAGE IMMEDIATELY:
Regardless of the extent of the damage.
3. CONCEALED LOSS OR DAMAGE: if damage is
unnoticed until the merchandise is unpacked, notify the
transportation company or carrier immediately, and file
“CONCEALED DAMAGE” claim with them. This
should be done within fifteen (15) days from the date
the delivery was made to you. Be sure to retain the
container for inspection.
Wells Bloomfield cannot assume liability for damage or loss
incurred in transit. We will, however, at your request, supply
you with the necessary documents to support your claim.
xi
TABLE OF CONTENTS
WARRANTY xi
SPECIFICATIONS 1
FEATURES & OPERATING CONTROLS 2
PRECAUTIONS & GENERAL INFORMATION 3
AGENCY APPROVAL INFORMATION 3
INSTALLATION 4
OPERATION 6
TROUBLESHOOTING SUGGESTIONS 7
CLEANING INSTRUCTIONS 8
PARTS & SERVICE 9
CUSTOMER SERVICE DATA 9
INTRODUCTION
Thank You for purchasing this Wells Bloomfield dispenser.
Proper installation, professional operation and consistent maintenance of this dispenser will ensure that
it gives you the very best performance and a long, economical service life.
This manual contains the information needed to properly install this dispenser, and to use and care for
the dispenser in a manner which will ensure its optimum performance.
SPECIFICATIONS
MODEL DISH FLANGE REQ’D.
NO. DIA. DIA. CUTOUT*
UT4 UP TO 4” 7h ” 6d ” dia.
UT5 4d ”-5” 8h ” 7d ” dia.
UT57 5d ”-5H ” 9 ” 7d ” dia.
UT65 5L ”-6p ” 9H ” 8D ” dia.
UT7 6D ”-7h ” 10p ” 9l ” dia.
UT8 7L ”-8d ” 11L ” 10h ” dia.
UT9 8h ”-9d ” 12l ” 11h ” dia.
OPEN DROP-IN TUBES SHIELDED DROP-IN TUBES
UT10 9h ”-10h ” 13l ” 12l ” dia.
UT12 10l ”-12” 15d ” 14d ” dia.
UTS4 UP TO 4” 7h ” 6j ” dia.
UTS5 4d ”-5” 8h ” 7n ” dia.
UTS57 5d ”-5H
UTS65 5L ”-6p ” 9H ” 8D ” dia.
UTS7 6D ”-7h ” 10p ” 9F ” dia.
UTS8 7L ”-8d ” 11L ” 10B ” dia.
UTS9 8h ”-9d ” 12l ” 11B ” dia.
UTS10 9h ”-10h ” 13l ” 12B ” dia.
432 p/n 303848 OpM Self-Levelling Round Dishware Dispenser
UTS12 10l ”-12” 15d ” 14j ” dia.
* NOTE: Verify dimensions by referring to the Installation Instructions included with the dispenser.
For metric sizes refer to the Specification Sheet included with the dispenser.
UTH and UTY heated dispensers are shielded. UTS shielded dispensers are not heated.
” 9 ” 8f ” dia.
MODEL DISH FLANGE REQ’D. WATTS AMPS
NO. DIA. DIA. CUTOUT*
UTH4 UP TO 4” 7h ” 6j ” dia. 240 2.0
UTH5 4d ”-5” 8h ” 7n ” dia. 240 2.0
UTH57 5d ”-5H ” 9 ” 8f ” dia. 240 2.0
UTH65 5L ”-6p ” 9H ” 8D ” dia. 300 2.5
UTH7 6D ”-7h ” 10p ” 9F ” dia. 300 2.5
UTH8 7L ”-8d ” 11L ” 10B ” dia. 300 2.5
UTH9 8h ”-9d ” 12l ” 11B ” dia. 300 2.5
UTH10 9h ”-10h ” 13l ” 12B ” dia. 500 4.2
UTH12 10l ”-12” 15d ” 14j ” dia. 500 4.2
120V 1ø HEATED DROP-IN TUBES
UTY4 UP TO 4” 7h ” 6j ” dia. 240 1.0
UTY5 4d ”-5” 8h ” 7n ” dia. 240 1.0
UTY57 5d ”-5H
UTY65 5L ”-6p ” 9H ” 8D ” dia. 300 1.3
UTY7 6D ”-7h ” 10p ” 9F ” dia. 300 1.3
UTY8 7L ”-8d ” 11L ” 10B ” dia. 300 1.3
UTY9 8h ”-9d ” 12l ” 11B ” dia. 300 1.3
UTY10 9h ”-10h ” 13l ” 12B ” dia. 500 2.1
UTY12 10l ”-12” 15d ” 14j ” dia. 500 2.1
240V 1ø HEATED DROP-IN TUBES
” 9 ” 8f ” dia. 240 1.0
1
FEATURES & OPERATING CONTROLS
CARRIAGE
1
2
3
CARRIAGE
SPRINGS
1
2
3
KEY
1
UT Series
2
UTS Series
3
UTH Series
4
UTY Series
PLATE GUIDES
1
2
3
4
4
4
FLANGE
1
2
OPEN
TUBE
1
2
3
4
3
4
POWER
SWITCH
3
4
POWER
INDICATOR
3
4
TEMPERATURE
ADJUSTMENT
3
4
SHIELD
2
3
4
POWER
CORD
3
4
HEATING
ELEMENT
3
4
432 p/n 303848 OpM Self-Levelling Round Dishware Dispenser
Fig. 1 Features & Operating Controls - Drop-In Round Dinnerware Dispensers
2
Loading...