Wells T-4C, BT-4C, T-4C 15A User Manual

WELLS MANUFACTURING COMPANY

2 ERIK CIRCLE, P. O. Box 280

Verdi, NV 89439

Customer Service [phone] Ext.502

fax: [phone]

www.wellsbloomfield.com

OPERATION MANUAL

for

ELECTRONIC POP-UP TOASTERS

Models T-4C and T-4C 15A

and

BAGEL TOASTERS

201

Model BT-4C

Includes

INSTALLATION

USE & CARE

Model T-4C

IMPORTANT: DO NOT DISCARD THIS MANUAL

This manual is considered to be part of the appliance and is to be given to the OWNER or
MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of

this appliance. Additional manuals are available from your WELLS DEALER.

THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR

INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any

questions concerning installation, operation or maintenance of this equipment.

p/n 40091 Rev. E M201 020601 cps

LIMITED WARRANTY STATEMENT

Unless otherwise specified, all commercial cooking equip­ment manufactured by WELLS MFG. CO. is warranted
against defects in materials and workmanship for a period of
one year from the date of original installation or 18 months
from the date of shipment from our factory, whichever
comes first, and is for the benefit of the original purchaser
only.
THIS WARRANTY IS THE COMPLETE AND ONLY WAR­RANTY, EXPRESSED OR IMPLIED IN LAW OR IN FACT,
INCLUDING BUT NOT LIMITED TO, WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICU­LAR PURPOSE, AND/OR FOR DIRECT, INDIRECT OR
CONSEQUENTIAL DAMAGES IN CONNECTION WITH
WELLS MFG. CO. PRODUCTS. This warranty is void if it
is determined that, upon inspection by an authorized service
agency, the equipment has been modified, misused, misap­plied, improperly installed, or damaged in transit or by fire,
flood or act of God. It also does not apply if the serial name­plate has been removed, or if service is performed by unau-

SERVICE POLICY AND PROCEDURE GUIDE

ADDITIONAL WARRANTY EXCLUSIONS

1. Resetting of safety thermostats, circuit breakers, over
load protectors, and/or fuse replacements are not
covered by this warranty unless warranted conditions
are the cause.

2. All problems due to operation at voltages or phase
other than specified on equipment nameplates are
not covered by this warranty.
Conversion to correct voltage and/or phase must be
the customer’s responsibility.

3. All problems due to electrical connections not made

in accordance with electrical code requirements
and wiring diagrams supplied with the equipment are

not covered by this warranty.

4. Replacement of items subject to normal wear, to
include such items as knobs, light bulbs; and, normal
maintenance functions including adjustments of
thermostats, adjustment of micro switches and
replacement of fuses and indicating lights are not
covered by warranty.

5. Damage to electrical cords and/or plug due to exposure
to excessive heat are not covered by this warranty.

6. Full use, care, and maintenance instructions supplied
with each machine. Noted maintenance and

preventative maintenance items, such as servicing and

thorized personnel. The prices charged by Wells Mfg. Co.
for its products are based upon the limitations in this war­ranty. Seller’s obligation under this warranty is limited to the
repair of defects without charge by a Wells Mfg. Co. factory
authorized service agency or one of its sub-service agen­cies. This service will be provided on customer’s premises
for non-portable models. Portable models (a device with a
cord and plug) must be taken or shipped to the closest au­thorized service agency, transportation charges prepaid, for
service. In addition to restrictions contained in this warranty,
specific limitations are shown in the Service Policy and Pro­cedure Guide. Wells Mfg. Co. authorized service agencies
are located in principal cities. This warranty is valid in the
United States and Canada and void elsewhere. Please con­sult your classified telephone directory, your foodservice
equipment dealer or write the Factory Service Department,
Wells Manufacturing Company, P.O. Box 280, Verdi, Ne­vada 89439, phone [phone] or [phone], for
information and other details concerning warranty.

cleaning schedules, are customer responsibility. Those
miscellaneous adjustments noted are customer
responsibility. Proper attention to preventative
maintenance and scheduled maintenance procedures
will prolong the life of the appliance.

7. Travel mileage is limited to sixty (60) miles from an
Authorized Service Agency or one of its sub-service
agencies.

8. All labor shall be performed during regular working
hours. Overtime premium will be charged to the buyer.

9. All genuine Wells replacement parts are warranted for
ninety (90) days from date of purchase on non­warranty equipment. This parts warranty is limited only
to replacement of the defective part(s). Any use of

non-genuine Wells parts completely voids any

warranty.

10. Installation, labor, and job check-outs are not

considered warranty and are thus not covered by this
warranty.

11. Charges incurred by delays, waiting time or operating

restrictions that hinder the service technician’s ability to
perform service are not covered by warranty. This
includes institutional and correctional facilities.

SHIPPING DAMAGE CLAIM PROCEDURE

NOTE: For your protection, please note that equipment in

this shipment was carefully inspected and packaged by
skilled personnel before leaving the factory. Upon accep­tance of this shipment, the transportation company assumes
full responsibility for its safe delivery.
IF SHIPMENT ARRIVES DAMAGED:

1. VISIBLE LOSS OR DAMAGE: Be certain that any
visible loss or damage is noted on the freight bill or
express receipt, and that the note of loss or damage is
signed by the delivery person.

2. FILE CLAIM FOR DAMAGE IMMEDIATELY:

Regardless of the extent of the damage.

3. CONCEALED LOSS OR DAMAGE: if damage is
unnoticed until the merchandise is unpacked, notify the
transportation company or carrier immediately, and file
“CONCEALED DAMAGE” claim with them. This
should be done within fifteen (15) days from the date
the delivery was made to you. Be sure to retain the
container for inspection.

Wells Manufacturing cannot assume liability for damage or
loss incurred in transit. We will, however, at your request,
supply you with the necessary documents to support your
claim.

xi

TABLE OF CONTENTS

WARRANTY xi
SPECIFICATIONS 1
FEATURES & OPERATING CONTROLS 2
PRECAUTIONS &GENERAL INFORMATION 3
AGENCY APPROVAL INFORMATION 3

very best performance and a long,

INSTALLATION 4
OPERATION 5
CLEANING INSTRUCTIONS 6
TROUBLESHOOTING 7
PARTS & SERVICE 9
CUSTOMER SERVICE DATA 9

SPECIFICATIONS

DIMENSIONS:

Cabinet 12”H x 13-1/8”W x 9-1/16”D

Bread Slot 1-1/8” x 5-1/4”

Slices per Load 1 to 4

ELECTRICAL:
MODEL VOLTS AMPS kW PLUG

T-4C 208V 11.5A 2.4 kW NEMA 6-15P

240V 10.0A 2.4 kW NEMA 6-15P

T-4C 15A 120V 15.0A 1.8 kW NEMA 5-15P

BT-4C 120V 13.3A 1.6 kW NEMA 5-15P

Thank You for purchasing this

Wells Manufacturing Co.

Electronic Pop-Up Toaster.

Proper installation, professional

operation and consistent
maintenance of this equipment
will ensure that it gives you the

economical service life.

This manual contains the

information needed to properly

install this equipment, and to use

and care for the equipment in a

manner which will ensure its

optimum performance.

1

FEATURES & OPERATING CONTROLS

SLIDE

KNOBS

(1 per 2

slots,

2 total)

DARKNESS

CONTROL

KNOBS
(1 per 2

slots,

2 total)

CRUMB

TRAY

Fig. 1 Toaster Features & Operating Controls

BREAD SLOTS

(4 total)

ELEMENTS
(2 per slot,
8 total)

CARRY

HANDLES

(1 each side)

POWER
CORD

BREAD GUIDES
(2 per slot,
8 total)

SLIDE

RACKS

(1 per 2

slots,

2 total)

INTERNAL COMPONENTS

n BREAD SLOTS One to four pieces of bread, one slice of bread per slot.
Oversized to accept Texas toast, English muffin, bagel, etc.

n BREAD GUIDES Hold bread at proper distance from elements

n SLIDE RACKS Carriages hold bread slices for toasting
Controlled by slide knobs

n ELEMENTS Provide toasting heat.
Note: Bagel toaster BT-4C toasts one side (cut side) only
One element in each pair is inert

n DARKNESS Individually adjustable from very light to very dark
CONTROL Control time slide rack is down and elements are energized
KNOBS Each knob controls one pair of bread slots

n SLIDE KNOBS Control slide racks. Initiate toasting timer when pushed
down. Each knob controls one slide rack (one pair of bread
slots)

n POWER CORD Plugs into appropriate electrical receptacle

n CARRY HANDLES Carry the toaster here
DO NOT carry the toaster by the bread slots!

n CRUMB TRAY Crumbs accumulate here. Remove to dump crumbs

2