Wells RWT-3HD Operation Manual

WELLS MANUFACTURING

10 Sunnen Dr., St. Louis, MO 63143

telephone: [phone]

fax: [phone]

www.wellsbloomfield.com

OPERATION MANUAL

FREE STANDING DRAWER WARMERS

with SOLID STATE CONTROLLER

MODELS

RWT-1HD thru RWT-3HD

RWNT-1 thru RWNT-3 Narrow

Includes

INSTALLATION and USE & CARE

047

Model RWT-2HD

Model RWNT-2

IMPORTANT: DO NOT DISCARD THIS MANUAL

This manual is considered to be part of the appliance and is to be given to the OWNER or
MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of
this appliance. Additional manuals are available from your WELLS DEALER.

THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR
INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any

questions concerning installation, operation or maintenance of this equipment.

p/n 2M-307538 Rev. A M047 111220

LIMITED WARRANTY STATEMENT

Unless otherwise specied, all commercial cooking equip-
ment manufactured by Wells Manufacturing is warranted

against defects in materials and workmanship for a period of

one year from the date of original installation or 18 months
from the date of shipment from our factory, whichever comes

rst, and is for the benet of the original purchaser only.

THIS WARRANTY IS THE COMPLETE AND ONLY
WARRANTY, EXPRESSED OR IMPLIED IN LAW
OR IN FACT, INCLUDING BUT NOT LIMITED TO,
WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR ANY PARTICULAR PURPOSE, AND/OR FOR
DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES
IN CONNECTION WITH WELLS PRODUCTS. This
warranty is void if it is determined that, upon inspection
by an authorized service agency, the equipment has been

modied, misused, misapplied, improperly installed, or
damaged in transit or by re, ood or act of God. It also

does not apply if the serial nameplate has been removed,
or if service is performed by unauthorized personnel.

The prices charged by Wells Bloomeld for its products

are based upon the limitations in this warranty. Seller’s

obligation under this warranty is limited to the repair of
defects without charge by a Wells Manufacturing factory
authorized service agency or one of its sub-service
agencies. This service will be provided on customer’s
premises for non-portable models. Portable models (a

device with a cord and plug) must be taken or shipped

to the closest authorized service agency, transportation
charges prepaid, for service. In addition to restrictions

contained in this warranty, specic limitations are shown in
the Service Policy and Procedure Guide. Wells Bloomeld

authorized service agencies are located in principal cities.
This warranty is valid in the United States and Canada and

void elsewhere. Please consult your classied telephone

directory, your foodservice equipment dealer or contact:

Wells Manufacturing

10 Sunnen Dr., St. Louis MO 63143 USA

phone [phone] or fax [phone]

for information and other details concerning warranty.

SERVICE POLICY AND PROCEDURE GUIDE and ADDITIONAL WARRANTY EXCLUSIONS

1. Resetting of safety thermostats, circuit breakers, over

load protectors, and/or fuse replacements are not
covered by this warranty unless warranted conditions
are the cause.

2. All problems due to operation at voltages or phase

other than specied on equipment nameplates are

not covered by this warranty.
Conversion to correct voltage and/or phase must be
the customer’s responsibility.

3. All problems due to electrical connections not made
in accordance with electrical code requirements and
wiring diagrams supplied with the equipment are not
covered by this warranty.

4. Replacement of items subject to normal wear, to

include such items as knobs, light bulbs; and, normal

maintenance functions including adjustments of

thermostats, adjustment of micro switches and
replacement of fuses and indicating lights are not
covered by warranty.

5. Damage to electrical cords and/or plug due to exposure

to excessive heat are not covered by this warranty.

6. Full use, care, and maintenance instructions supplied
with each machine. Noted maintenance and

preventative maintenance items, such as servicing and

cleaning schedules, are customer responsibility. Those
miscellaneous adjustments noted are customer
responsibility. Proper attention to preventative
maintenance and scheduled maintenance procedures
will prolong the life of the appliance.

7. Travel mileage is limited to sixty (60) miles from an
Authorized Service Agency or one of its sub-service
agencies.

8. All labor shall be performed during regular working

hours. Overtime premium will be charged to the buyer.

9. All genuine Wells replacement parts are warranted
for ninety (90) days from date of purchase on non­warranty equipment. This parts warranty is limited only
to replacement of the defective part(s). Any use of
non-genuine Wells parts completely voids any
warranty.

10. Installation, labor, and job check-outs are not

considered warranty and are thus not covered by this

warranty.

11. Charges incurred by delays, waiting time or operating
restrictions that hinder the service technician’s ability to
perform service are not covered by warranty. This
includes institutional and correctional facilities.

SHIPPING DAMAGE CLAIM PROCEDURE

NOTE: For your protection, please note that equipment

in this shipment was carefully inspected and packaged by
skilled personnel before leaving the factory. Upon accep-

tance of this shipment, the transportation company assumes
full responsibility for its safe delivery.

IF SHIPMENT ARRIVES DAMAGED:

1. VISIBLE LOSS OR DAMAGE: Be certain that any
visible loss or damage is noted on the freight bill or
express receipt, and that the note of loss or damage is
signed by the delivery person.

2. FILE CLAIM FOR DAMAGE IMMEDIATELY:

Regardless of the extent of the damage.

3. CONCEALED LOSS OR DAMAGE: if damage is

unnoticed until the merchandise is unpacked, notify the

transportation company or carrier immediately, and le

“CONCEALED DAMAGE” claim with them. This

should be done within fteen (15) days from the date

the delivery was made to you. Be sure to retain the
container for inspection.

Wells Manufacturing cannot assume liability for damage or
loss incurred in transit. We will, however, at your request,
supply you with the necessary documents to support your
claim.

xi

047 p/n 307538 OpM Free-Standing Drawer Warmer w/ Solid State Control

TABLE OF CONTENTS

WARRANTY xi
SPECIFICATIONS 1
FEATURES & OPERATING CONTROLS 2
PRECAUTIONS & GENERAL INFORMATION 3
AGENCY LISTING INFORMATION 3
INSTALLATION 4
OPERATION 6
CLEANING INSTRUCTIONS 10
TROUBLESHOOTING SUGGESTIONS 11
MAINTENANCE INSTRUCTIONS 12
PARTS & SERVICE 13
CUSTOMER SERVICE DATA 13

INTRODUCTION

Thank You for purchasing this Wells Manufacturing appliance.

Proper installation, professional operation and consistent maintenance of this appliance will ensure that it
gives you the very best performance and a long, economical service life.

This manual contains the information needed to properly install this appliance, and to use and care for the
appliance in a manner which will ensure its optimum performance.

MODELS

RWT-1HD, RWNT-1

RWT-2HD, RWNT-2

RWT-3HD, RWNT-3

SPECIFICATIONS

VOLTS

50/60 Hz 1ø

120 VAC 450 W 3.8 NEMA-5-15P

208/240 VAC 338/450 W 1.6/1.9 NEMA 6-15P

120 VAC 900 W 7.5 NEMA-5-15P

208/240 VAC 676/900 W 3.3/3.8 NEMA 6-15P

120 VAC 1350 W 11.3 NEMA-5-15P

208/240 VAC 1014/1350 W 4.9/5.6 NEMA 6-15P

WATTS AMPS POWER CORD

047 p/n 307538 OpM Free-Standing Drawer Warmer w/ Solid State Control

1

FEATURES & OPERATING CONTROLS

CONTROL MODULE

HUMITROL

RACK

DRAWER

INSERT PAN

AIR VENT
CONTROL

DRAWER

STOP

DECREMENT KEYS

ADJUSTABLE

LEG

ROLLER
CATCH

LED READOUT

"PROCESS" KEY

INCREMENT AND

PROCESS

POWER SWITCH

CONTROL MODULE

POWER CORD

DRAWER

GASKET

ºF OR ºC
INDICATORS

LOAD
INDICATOR

DRAWER

ROLLER

DRAWER

SLIDE

HEATING

ELEMENT

2

DRAWER

CATCH

DRAWER
SLIDE

DRAWER
ROLLERS

IL1937, Rev. -, M047

047 p/n 307538 OpM Free-Standing Drawer Warmer w/ Solid State Control

PRECAUTIONS AND GENERAL INFORMATION

This appliance is intended for use in commercial establishments
only.

This appliance is intended
No other use is recommended or authorized by the manufacturer or its
agents.

Operators of this appliance must be familiar with the appliance use,
limitations and associated restrictions. Operating instructions must be
read and understood by all persons using or installing this appliance.

Cleanliness of this appliance is essential to good sanitation. Read and
follow all included cleaning instructions and schedules to ensure the
safety of the food product.

Disconnect this appliance from electrical power before performing any
maintenance or servicing.

DO NOT submerge this appliance in water. This appliance is not jet
stream approved. Do not direct water jet or steam jet at this appliance,
or at any control panel or wiring. Do not splash or pour water on, in or

over any controls, control panel or wiring. Do not wash oor around

this appliance with water or steam jet.

Exposed surfaces of this appliance can be hot to the touch and may
cause burns.

Heating element will be very hot when in use. Contact may cause
serious burns.

The technical content of this manual, including any wiring diagrams,

schematics, parts breakdown illustrations and/or adjustment
procedures, is intended for use by qualied technical personnel.

Any procedure which requires the use of tools must be performed by a

qualied technician.

This manual is considered to be a permanent part of the appliance.
This manual and all supplied instructions, diagrams, schematics, parts

breakdown illustrations, notices and labels must remain with the

appliance if it is sold or moved to another location.

to prepare food for human consumption.

WARNING:

SHOCK HAZARD

All servicing requiring
access to non-insulated
electrical components must
be performed by a factory
authorized technician.
DO NOT open any access
panel which requires the use
of tools. Failure to
follow this warning can
result in severe electrical

shock.

CAUTION:

RISK OF
DAMAGE

DO NOT connect or energize
this appliance until all
installation instructions are
read and followed. Damage
to the appliance will result if
these instructions are not
followed.

CAUTION:

HOT SURFACE

Exposed surfaces can be hot
to the touch and may cause
burns.

This appliance is made in the USA. Unless otherwise noted, this
appliance has American sizes on all hardware.

This appliance conforms to NSF Standard 4 for sanitation only if
installed in accordance with the supplied Installation Instructions and
maintained according to the instructions in this manual.

This appliance is NSF approved for potentially hazardous foods.

This appliance is and Listed under UL File E6070 for 120V, 208V
and 240V.

047 p/n 307538 OpM Free-Standing Drawer Warmer w/ Solid State Control

3

AGENCY LISTING INFORMATION

STD 4

E6070

E6070