Weller T0052916699N User manual

Fume Extraction Irons

Betriebsanleitung - Mode d’emploi - Istruzioni per l’uso - Operating Instructions

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

English

Always place the soldering tool in the safety rest while not in use.

Description

Weller FE soldering irons are designed for use with the Zero-Smog system and are equipped
with an integrated extraction tube to remove unpleasant and dangerous fumes directly
where they occur: at the solder tip. The tip temperature is not effected.

Setting up

1. Replace the enclosed funnel against the original one. Make sure that the suction tube is
in upper position and does not touch the spring holder when the iron is in rest position.

2. Adjust the extraction tube to the tip. The end of tube should be vertical above the tip
when the iron is in soldering position.

3. Store soldering iron in safety holder.

4. Plug in and latch the electrical connector on the power unit.

FE 50 M to PU S.

FE 50 and MLR 21 FE to all Temtronic power supply units
FE 75 to all power supply units with 80 W.

FE 80 to all power supply units with 80 W.

5. connect the silicone suction hose to the Zero-Smog or vaccum pipe system.

Maintenance

The extraction tube has a small bending radius to hold the tube in the shaft of the soldering
iron handle. If the extraction tube should become loose during use, it can be tightened by
bending slightly.

Warning:

When using cleaning agents, legal safety regulations regarding their use must be observed.
The cleaning agent must be treated as hazardous waste and must be disposed of according
to curent local guidelines.

In order to ensure correct function, the extraction hose should also be cleaned regularly. The
hose must first be unplugged and allowed to cool. Knead the hose between the fingers until
the condensed fluxing media residues are loosened and are emoved by the turbine.

Safety Informations

● Always place the soldering iron in the original holder.

● Remove all inflammable objects from the proximity of the hot soldering tool.

● Use suitable protective clothing. Risk of burns from liquid solder.

● Never leave the hot soldering iron unsupervised.

● Never work on voltage-carrying parts.

The instructions for the use of the supply unit are valid in addition of these here.

The extraction tube should be cleaned once daily with the special brush. In order to avoid
burns, the tube should be cleaned only after cooling. If the tube is extremely dirty, it can be
placed in a closed container of cleaning alcohol (Spirit) until the fluxing media residues and
loosened.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

4

FE 50 M

5.

4.

8.

1. Kabel

2. Absaugschlauch

3. Griff

4. Spitzenhülse

5. PT- Longlife- Spitze

6. Absaugrohr

7. Biegeschutzfeder

8. PT- ET Adapter

5

1. Cordon

2. Tuyau d’aspiration

3. Manche

4. Douille pointue

5. Panne PT

6. Tube d’aspiration

7. Vis de serrage

8. PT-ET Adaptateur

1. Cordone di alimentazione

2. Tubetto siliconico di aspirazione

3. Impugnatura

4. Fermapunta

5. Punta long- life serie PT

6. Tubetto metallico di aspirazione

7. Vite di fissaggio

8. PT-ET Adattatore

1. Cord

2. Suction hose

3. Handle

4. Barrel

5. PT- Longlife- Tip

6. Suction tube

7. Strain relief spring

8. PT-ET Adapter

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

FE 50 M

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

6

FE 50

5.

4.

8.

1. Kabel

2. Absaugschlauch

3. Griff

4. Spitzenhülse

5. ET- Longlife- Spitze

6. Absaugrohr

7. Biegeschutzfeder

8. PT- ET Adapter

7

1. Cordon

2. Tuyau d’aspiration

3. Manche

4. Douille pointue

5. Panne ET

6. Tube d’aspiration

7. Vis de serrage

8. PT-ET Adaptateur

1. Cordone di alimentazione

2. Tubetto siliconico di aspirazione

3. Impugnatura

4. Fermapunta

5. Punta long- life serie ET

6. Tubetto metallico di aspirazione

7. Vite di fissaggio

8. PT-ET Adattatore

1. Cord

2. Suction hose

3. Handle

4. Barrel

5. ET- Longlife- Tip

6. Suction tube

7. Strain relief spring

8. PT-ET Adapter

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

FE 50

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

8

FE 75

1. Kabel

2. Absaugschlauch

3. Griff

4. Spitzenhülse

5. LT- Longlife- Spitze

6. Absaugrohr

7. Biegeschutzfeder

9

1. Cordon

2. Tuyau d’aspiration

3. Manche

4. Douille pointue

5. Panne LT

6. Tube d’aspiration

7. Vis de serrage

1. Cordone di alimentazione

2. Tubetto siliconico di aspirazione

3. Impugnatura

4. Fermapunta

5. Punta long- life serie LT

6. Tubetto metallico di aspirazione

7. Vite di fissaggio

1. Cord

2. Suction hose

3. Handle

4. Barrel

5. LT- Longlife- Tip

6. Suction tube

7. Strain relief spring

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

FE 75

10

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Adapter und Spitzen für FE 50, FE 50M und FE 75
Adapter and Tips for FE 50, FE 50M and FE 75

Beschreibung / Modell Breite Bestell-Nr.
Description / Model Width Order-No.

Barrel for MT-LT Adapter 5 87 207 95
Barrel for ET-PT / LT Adapter 5 87 207 94
Barrel for ET, PT Tip 5 10 311 99

ET-LT Adapter with barrel 5 87 207 81

PT-LT Adapter with barrel
PT5-LT 5 87 207 85
PT6-LT 5 87 207 86
PT7-LT 5 87 207 87
PT8-LT 5 87 207 88
PT9-LT 5 87 207 89

MT-LT Adapter with barrel 5 44 121 99

Beschreibung / Modell Breite Bestell-Nr.
Description / Model Width Order-No.

Meißelform / Chisel
LT H 0,8 mm 5 44 412 00
LT A 1,6 mm 5 44 403 00
LT B 2,4 mm 5 44 405 00
LT C 3,2 mm 5 44 407 00
LT D 4,6 mm 5 44 409 00
ET E 5,6 mm 4ETE

Meißelform lang / Chisel long
LT K 1,2 mm 5 44 413 00
LT L 2,0 mm 5 44 414 00
LT M 3,2 mm 5 44 415 00

Meißelform geb. 30° / Chisel bent 30°
LT HX 0,8 mm 5 44 420 99
LT ALX 1,6 mm 5 44 443 00
LT BX 2,4 mm 5 44 442 00

Rundform abgeschrägt 45° lang
Chisel sloped 45° long
LT CC45 3,2 mm 5 44 445 00
LT DD45 4,0 mm 5 44 478 00
LT DDLL 4,6 mm 5 44 486 00
Rundform abgeschrägt 60° lang
Chisel sloped 60° long
LT AA60 1,6 mm 5 44 487 00
LT BB60 2,4 mm 5 44 444 00

11

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Spitzen für FE 50, FE 50M und FE75
Tips for FE 50, FE 50M and FE 75

Beschreibung / Modell Breite Bestell-Nr.
Description / Model Width Order-No.

Konisch lang / Conical long
LT 1L Ø 0,2 mm 5 44 423 00
LT S Ø 0,4 mm 5 44 406 00

LT O Ø 0,8 mm 5 44 481 00
LT T Ø 0,6 mm 5 44 482 00

Konisch lang / Conical long
LT 1LX Ø 0,25 mm 5 44 424 00

Lotdepotspitze 45° / Gull wing 45°
LT GW Ø 2,3 mm 5 44 410 00

Ø 3,5 mm 5 44 511 99

Messerspitze / Knife tip
LT KN 6,2 mm 5 44 479 00

Rundform / Round tip
LT 1 Ø 0,25 mm 5 44 401 00
LT AS Ø 1,6 mm 5 44 404 00
LT BS Ø 2,4 mm 5 44 499 00
LT CS Ø 3,2 mm 5 44 411 00

Beschreibung / Modell Breite Bestell-Nr.
Description / Model Width Order-No.

Rundform schlank gebogen 30°
Chisel slim bent 30°
LT 1SLX Ø 2,0 mm 5 44 426 99

12

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

FE 80

1. Kabel

2. Absaugschlauch

3. Griff

4. Spitzengehäuse

5. HT- Longlife- Spitze

6. Absaugrohr

7. Biegeschutzfeder

13

1. Cordon

2. Tuyau d’aspiration

3. Manche

4. Forreau

5. Panne HT

6. Tube d’aspiration

7. Vis de serrage

1. Cordone di alimentazione

2. Tubetto siliconico di aspirazione

3. Impugnatura

4. Tubetto fermapunta

5. Punta long- life serie HT

6. Tubetto metallico di aspirazione

7. Vite di fissaggio

1. Cord

2. Suction hose

3. Handle

4. Barrel

5. HT- Longlife- Tip

6. Suction tube

7. Strain relief spring

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

HT Spitzen für FE 80
HT Tips for FE 80

Modell Beschreibung Bestell-Nr.
Model Description Order-No.

Modell Beschreibung Bestell-Nr.
Model Description Order-No.

HT 1 Meißelform 3,2 mm 5 44 260 99

Chisel tip 3,2 mm

HT 2 Meißelform 5,2 mm 5 44 261 99

Chisel tip 5,2 mm

HT 3 Meißelform 7,0 mm 5 44 262 99

Chisel tip 7,0 mm

HT C Flachform 3,2 mm 5 44 267 99

Chisel tip, 3,2 mm

HT D Flachform 4,6 mm 5 44 268 99

Chisel tip 4,6 mm

HT E Flachform 5,6 mm 5 44 269 99

Round tip 3,2

HT BS Rundform 2,4 mm 5 44 264 99

Round tip 2,4 mm

HT CS Rundform 3,2 mm 5 44 2665 99

Round tip 3,2 mm

HT DS Rundform 5,0 mm 5 44 266 99

Round tip 5,0 mm

HT Einschraubspitze
mit M8 Außengewinde 5 44 270 99
HT Screw in tip with
outside thread M8

Messspitze 5 44 263 99
Calibration tip

14

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

FE 80

15

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Weller®is a registered Trademark and registered Design of Apex Tool Group, LLC
© 2013, Apex Tool Group, LLC

T005 55 275 10 / 09.2013
T005 55 275 09 / 10.2012

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com