Wellav UMH-150 User Manual

UMH-150

Integrated Receiver Decoder

User Manual

Wellav Technologies Ltd

1

Table of Content

Safety ................................................................................................................................ 2

Reference .......................................................................................................................... 3

Features ............................................................................................................................. 4

Introduction ....................................................................................................................... 5

FRONT PANEL ............................................................................................................. 5

REAR PANEL .............................................................................................................. 5

RF IN AND ASI OUT .................................................................................................... 6

RF IN AND IP OUT ....................................................................................................... 7

RF IN AND SDI OUT .................................................................................................... 7

RF IN AND CVBS OUT ................................................................................................ 8

IP IN AND ASI OUT ..................................................................................................... 8

Front Panel Control & Operation ..................................................................................... 10

INPUT ...................................................................................................................... 12

Sources ................................................................................................ ............... 12

Params ................................................................................................................ 12

OUTPUT ................................................................................................................... 13

Program Setup .................................................................................................... 13

Decoder .............................................................................................................. 13

SDI ..................................................................................................................... 14

Ethernet .............................................................................................................. 14

SYSTEM ................................................................................................................... 15

Local Setup ......................................................................................................... 15

Properties ................................................................................................ ............ 15

Factory Setting .................................................................................................... 15

STATUS .................................................................................................................... 15

Input status ......................................................................................................... 15

Outputs status ..................................................................................................... 15

NMS Control & Operation .............................................................................................. 16

LAN PARAMETERS SETTING & CONNECTION ESTABLISHMENT .................................... 16

Local network setting .......................................................................................... 16

Connection.......................................................................................................... 16

NMS MAIN INTERFACE CONFIGURATION .................................................................. 18

Troubleshooting .............................................................................................................. 24

Specifications .................................................................................................................. 26

Optional Models .............................................................................................................. 27

UMH 150 Integrated Receiver Decoder User Manual

2

Safety

 To avoid electric-shock hazards, do not open the receiver; refer service to qualified

personnel only.

 Keep the receiver away from flower vases, tubs, sinks, etc., in order to avoid damaging

the equipment.

 Do not expose the receiver in the sunlight. And keep it away from the heat source.
 Do not block ventilation holes of the Receiver so that air can circulate freely.
 When the abnormal phenomenon occurs, cut off the power immediately.
 Do not touch the receiver during thunder. That might create electric shock hazards.
 Switch the receiver off whenever it remains out of service for an extended period.
 Be sure to turn the receiver off and disconnect the AC power cord before cleaning the

receiver surface. If the surface is dirty, wipe clean with a cloth that has been dipped in
a diluted soap water solution and wrung out thoroughly, and then wipe again with a dry
cloth.

 Specifications and functions may be changed for improvement without notice in

advance.

UMH 150 Integrated Receiver Decoder User Manual

3

Reference

 Connect DiSEqC 1.0/1.2/2.0

The receiver is designed to be DiSEqC 1.0/1.2/2.0 compatible. This allows multiple
antennas to be connected to the receiver simultaneously. If you have two or more fixed
antennas or LNBs, you can use a DiSEqC 1.0/1.2/2.0 switch.

1. Connect the coaxial cable from the first LNB to the LNB 1 or LNB A input connectors

of the DiSEqC switch.

2. Connect the coaxial cable from the second LNB to the LNB 2 or LNB B input

connector of the DiSEqC switch.

3. Do the same for other LNBs.

4. Connect one end of a coaxial cable to the RF output connector of the DiSEqC switch

and the other end of the coaxial cable to the LNB IN socket on the receiver.

 Connect a Satellite Antenna

To UMH150 IRD, you can connect either a single satellite antenna directly or through
converter box several antennas or LNB of multi-feed equipment.
You can connect a further IRD with the IRD that has common antenna equipment to
receive satellite signals.

 Loop Through

If you wish, you can connect the same LNB to another IRD via the loop through of your
digital receiver decoder. Connect one end of a coaxial cable to the LNB OUT on the IRD
and connect the other end to the LNB IN on your second IRD.

UMH 150 Integrated Receiver Decoder User Manual

4

Features

 MPEG-2 Digital & Fully DVB-S ETSI/EN300 421 compliant
 Input Frequency 950-2150 MHz, Symbol Rate 2 ~ 45 Ms/s

 1 LNB Input (F-Type) and Loop-through IF Signal.
 2 DVB Common Interface (CI ) for descrambling most common CA system.
 SCPC & MCPC Receivable from C/Ku-Band.
 DiSEqC 1.0/1.2/2.0 compatible.

 Up to 5000 TV & Radio channels and 2000 transponders programmable
 1 ASI transport stream input & 1 ASI output capable of working as TS decoder
 IP stream input (optional)
 2 DVB Common Interface for descrambling most common CA systems
 Broadcasting quality video and audio outputs
 VBI teletext handling
 Balance audio output (XLR)
 BNC-interfaced CVBS output
 SDI signal output
 IP stream output (optional)
 Full control via front panel or Ethernet port
 DVB-S2/C/T signal input support (optional)
 Automatic recovery for latest system configuration from unexpected power off

 Software upgrading via RS232 port or NMS

UMH 150 Integrated Receiver Decoder User Manual

5

Introduction

The UHM150 IRD is an advanced MPEG-2 DVB integrated receiver decoder with optional
TS-IP mutual conversion function. It can receive signal from different program sources. Its
prolific output interface such as IP, SDI, XLR and ASI can meet different system
requirements. The UHM150 also has 2 common interface slots which can decode multiple
scrambled channels. It is an ideal component for either a standard digital video or a IPTV
head-end system.

Front Panel

LED Indicator: Power: The LED lights on when the STB is power on.

Lock: The LED lights on when a channel is locked. Otherwise there is no

channel is locked.

Alarm: The LED lights on when there are some thing abnormal.

Display screen: Show the channel name of TV or Radio program and the configuration

information.
CI SLOTS: There are two CI slots for various CAS CAM (PCMCIA) cards
KEY PADS: SELECT KEY: To change channels, adjust volume and configure the IRD.

MENU: To enter the menu and the quit function of the sub menus.
OK: To confirm the operation in the setup.

Rear Panel

1. TUNER IN (RF IN): Connect to a RF or IF signal.

UMH 150 Integrated Receiver Decoder User Manual

6

2. TUNER OUT (LOOP OUT): Use it when connecting to another IRD (IF loop through
output from digital tuner).
3:ETHERNET : Network remote control.

4. RS-232: Connect to a personal computer for software upgrade.

5. ASI OUT: Output the standard MPEG-2 TS.
6: SDI OUT: Output the SID signal

7. ASI IN: BNC connector for TS input

6. VIDEO /AUDIO: Video signal output jack and Left/right audio output jack.

7.Cr/Cb/Y: Component output
8 XLRL : Balance Audio output

9.TS/IP: TS stream input or output in IP format.

10. POWER SUPPLY and POWER SWITCH: 170~260V (or 90~130V) AC, 50/60Hz.

RF in and ASI out

There are several ways of connecting the IRD to your existing Audio/TV system. We
recommend using one of the following set-ups for best results:

1. LNB connections

 Connect the coaxial cable from the LNB to the LNB IN socket on the STB.

UMH 150 Integrated Receiver Decoder User Manual

7

2. Motorized System (DiSEqC 1.0/1.2/2.0)

 Connect the coaxial cable from the REC of your motorized system (DiSEqC

1.0/1.2/2.0 Motor) to the LNB IN socket on the STB.

 Connect the coaxial cable from the LNB to the LNB connector in the DiSEqC

1.0/1.2/2.0 motor.

RF in and IP out

RF in and SDI out

UMH 150 Integrated Receiver Decoder User Manual

8

RF in and CVBS out

IP in and ASI out

UMH 150 Integrated Receiver Decoder User Manual

9

UMH 150 Integrated Receiver Decoder User Manual

10

Front Panel Control & Operation

This diagram is for DVB-C and DVB-T IRD

UMH 150 Integrated Receiver Decoder User Manual

11

This diagram is for DVB-S and DVB-S2 IRD

UMH 150 Integrated Receiver Decoder User Manual

12

Input

In this menu, there are two submenu used to select the input source and configure the input
parameters. They are SOURCES and PARAMS.

Sources

In this submenu, there are three options, TUNER,ASI and IPTV.
TUNER: when select this item, the receiver will search the signal from the tuner (from

LNB).

ASI: when select this item, the receiver will search the signal from the ASI input port.
IPTV: when the signal from the IP port, you can select this option.

Params

In this submenu, there are two items, they are TUNER: QPSK and IPTV. If you IRD is for
DVB-C/T, they are QAM, COFDOM and IPTV. According to different type IRD, set
different parameters.

TUNER QPSK:
In this option, several parameters are required to setup.

 LNB frequency: this is the LNB’s local oscillation (LO) frequency, every LNB have

one or two local oscillation frequencies, you can get this parameter from the LNB’s
provider.

 Satellite frequency: This is the satellite’s down frequency, every transponder have one

frequency, you can get this parameter from the satellite programs provider.

 Symbol rate: Every transponder have one symbol rate, you can get this parameter from

the satellite programs provider.

 LNB Voltage: LNB need the power supply, for receiving the programs from different

band ( C band or Ku band), the LNB need different power supply, the receiver can
supply the power to the LNB.(13V is for C band, 18V is for Ku band)

 LNB 22KHz: when on is select, the LNB will switch automatically between C band

and Ku band.

IPTV:

When the receiver wants to receive the signal from the internet, you need to configure these
parameters.

 Receiver: Select On or Off to open or close the IPTV function.
 Input Multi IP Addr: Set up the multicast IP address for receiving the IP signal.
 Input Multi UDP port: Set up the UDP port for receiving the IP signal.
 Input Protocol: Default setting.

UMH 150 Integrated Receiver Decoder User Manual

13

 IP Board IP Address: Default setting.
 IP Board SubNetMask: Default setting.
 IP Board MAC Address: Default setting.

Notice: When two or above pieces of UMH150 are working in IPTV at the same time,
you’d better set different ‘IP Board IP Address’ and ‘IP Board SubNetMask’ for each
equipment.

Output

In this menu, there are four submenu, they are programs setup, Decoder, SDI and Ethernet.

Program Setup

In this option, all the programs received will be list, and you can configure and edit these
programs.
 Bypass: They receiver will do nothing for all the programs and all the programs will be

transmitted.

 CI slot1: in the received programs, there maybe be some scrambled programs, select

this channel and you can use the card in slot1 to descramble this channel.

 CI solt2: in the received programs, there maybe be some scrambled programs , select

this channel and you can used the card in slot2 to descramble this channel.

 Delete: In all the received channels by receiver, if there are channels which you do not

want to transfer, you can select this channel and use “Delete” to delete this channel.

Decoder

In this menu, there are three items, Program List, Video and Audio.
Program List:
All the programs received by the receiver will be list here.
Video:

Configure the video parameter
 Video standard: in this item, you can select video standard include Auto, SECAM,

NTSC, PAL.

 Screen: set the screen aspect ratio in this item, include Auto,4:3Full, 16:9Full and

4:3Letter box.

 DVB subtitle Lang: DVB subtitle language
 EBU subtitle Lang: EBU subtitle language
 Fail Mode: include Black Screen and Still Screen. Black screen: when the receiver lost

the signal, keep the screen black. Still screen: when the receiver lost the signal, keep
the last picture on the screen.

UMH 150 Integrated Receiver Decoder User Manual

14

Audio:
Configure the audio parameter

 Audio:0-99
 Audio mode: include Stereo, Left, Right, Mono, Dual
 Audio Language: Select different audio language.

SDI

SDI setup: When use SDI output, you need to setup these parameters

 Audio PID: Setup the audio PID, the range is 0-99.
 Embed Audios: Include One&Two and None options.

Ethernet

When select the IP port as the output, you need to setup some parameters in this submenu.
There are 8 channels used to output IP stream.

 Stream IP Addr: Default setting ( Used to extend in the future)
 Stream Network: Default setting ( Used to extend in the future)
 Stream Gateway: Default setting ( Used to extend in the future)
 Stream Mac Address: Default setting ( Used to extend in the future)
 Stream UDP port: Default setting ( Used to extend in the future)
 Channel 1 Param Setup:

 CH 1 Transmit: Off /On
 CH 1 Program Setup: Add/Delete
 CH 1 Multicast Addr: Set up the multicast IP for broadcasting the IP signal
 CH 1 Port: Set up the UDP or RTP port for broadcasting the IP signal
 CH 1 Protocol: UDP/RTP
 CH 1 TS Packets: Configuration range is 1—7 (7 is recommended)
 CH 1 Time to Live: Configuration range is 1-5 (5 is recommended)
 Ch 1 Type of Service: It includes Normal, Monetary Cost, Max reliabiability, Max

Throughput, Min delay

 Channel 2 Param Setup: The same to Channel 1
 Channel 3 Param Setup: The same to Channel 1
 Channel 4 Param Setup: The same to Channel 1
 Channel 5 Param Setup: The same to Channel 1
 Channel 6 Param Setup: The same to Channel 1
 Channel 7 Param Setup: The same to Channel 1
 Channel 8 Param Setup: The same to Channel 1

UMH 150 Integrated Receiver Decoder User Manual

15

System

Under this menu, there are three submenu include Local Setup, Properties and Factory
Setting.

Local Setup

 IP address: Local IP setting for connecting to the server. This IP and the server’s IP

should be in the same section.

 Network Mask: Network Mask setting for connecting to the server.
 Gateway: Gateway setting for connecting to the server.
 Trap IP address: This IP should be the same as the server’s IP, before connection, it

will verify the server’s IP, if they are the same, the connection will be allowed.

Properties

 Mac Address: Query the receiver’s Mac Address.
 HW Version: Query the receiver’s hardware version.
 SW Version: Query the receiver’s software version.

Factory Setting

Take the receiver back to factory setting.

Status

There are two submenus under this menu. Input status and output status.

Input status

Query the input status, lock or unlock.

Outputs status

Decoder: In this item you can check the programs PMT, PN, AV, Video, Audio status.
CI: Check two CI’s status.

UMH 150 Integrated Receiver Decoder User Manual

16

NMS Control & Operation

Except using the front panel to configure and operate the equipment, UMH150 also
supplies the network management function. When you get the equipment, there should be a
CD contain the network management software with it. If you want to use the network
management software to control and operate the equipment, please copy the software form
the CD to your server (Computer).

LAN parameters setting & connection establishment

Before logging on the equipment, you should use the front panel to configure the local
network setting.

Local network setting

Let’s take an example to explain how to configure the local network for connection. We
assume the server’s IP is 192.168.1.2, network mask is 255.255.255.0 and gateway is

198.168.1.1. All these parameters in the equipment should be:

 IP address: Local IP setting for connecting to the server. This IP and the server’s IP

should be in the same section. For example is can be 192.168.1.x, x can be 3 to 254.

 Network Mask: Network Mask setting for connecting to the server. It should be the

same as server’s. 255.255.255.0.

 Gateway: Gateway setting for connecting to the server. It should be the same as

server’s. 198.168.1.1

 Trap IP address: This IP should be the same as the server’s IP, before connection, it

will verify the server’s IP, if they are the same, the connection will be allowed. It
should be 192.168.1.2.

Connection

Connect the server and equipment via Ethernet port with an Ethernet cable before running
the network management software on the server. Then the login interface will display as the
following picture.

Enter the user name and password, the default user name and password both are “admin”,
and then enter the IP address, the default IP is 192.168.1.16. Click button “login” to log on
the equipment. Click Changepassword, button, then you can enter the new password for the
equipment.

UMH 150 Integrated Receiver Decoder User Manual

17

Login Interface

UMH 150 Integrated Receiver Decoder User Manual

Chang the Password

18

NMS Main Interface Configuration

After successfully logging in, the main interface will display as below:

DVB-S (MainBoard)

On the main interface of the network management software, there are two menus including
twelve parts. All these parts are the same as the front panel display.

Main Board:

Ⅰ. SOURCE
In this submenu, there are three options, TUNER,ASI and IPTV.

TUNER: when select this item, the receiver will search the signal from the tuner (from
LNB).

ASI: when select this item, the receiver will search the signal from the ASI input port.
IPTV: when the signal from the IP port, you can select this option.

Ⅱ. QPSK
In this option, there are several parameters need to setup.

 LNB frequency: this is the LNB’s local oscillation (LO) frequency, every LNB have

one or two local oscillation frequencies, you can get this parameter from the LNB’s

provider.

 Satellite frequency: This is the satellite’s down frequency, every transponder have one

frequency, you can get this parameter from the satellite programs provider.

UMH 150 Integrated Receiver Decoder User Manual

19

DVB-S2 (MainBoard)

UMH 150 Integrated Receiver Decoder User Manual

DVB-C/T (MainBoard)

20

DVB-S/S2/C/T (Ethernet)

 Symbol rate: Every transponder have one symbol rate, you can get this parameter from

the satellite programs provider.

 LNB Voltage: LNB need the power supply, for receiving the programs from different

band ( C band or Ku band), the LNB need different power supply, the receiver can
supply the power to the LNB.(13V is for C band, 18V is for Ku band)

 LNB 22KHz: when on is select, the LNB will switch automatically between C band and Ku band.

Ⅲ. System

 IP address: Local IP setting for connecting to the server. This IP and the server’s IP

should be in the same section.

 Network Mask: Network Mask setting for connecting to the server.
 Gateway: Gateway setting for connecting to the server.
 Trap IP address: This IP should be the same as the server’s IP, before connection, it

will verify the server’s IP, if they are the same, the connection will be allowed.

 Mac Address: Query the receiver’s Mac Address.

Ⅳ. Video

Configure the video parameter
 Video standard: in this item, you can select video standard include Auto, SECAM,

UMH 150 Integrated Receiver Decoder User Manual

21

NTSC, PAL.

 Screen Mode: set the screen aspect ratio in this item, include Auto, 4:3 Full, 16:9Full

and 4:3Letter box.

 DVB subtitle Language: DVB subtitle language
 EBU subtitle Language: EBU subtitle language
 Fail Mode: include Black Screen and Still Screen. Black screen: when the receiver lost

the signal, keep the screen black. Still screen: when the receiver lost the signal, keep
the last picture on the screen.

Ⅴ. Audio

Configure the audio parameter

 Audio:0-99
 Audio mode: include Stereo, Left, Right, Mono, Dual
 Audio Language: Select different audio language.

Ⅵ . SDI setup

 Audio PID: Setup the audio PID, the range is 0-99.
 Embed Audios: Include One &Two and None options.

Ⅶ. Program list

In the programs list box, all the received programs will be list. There are three item will
show the programs information: Program Number, Program Status and program Name. Let
take Channel [V] (NO.21) as an example to explain how to edit the programs status.
As the following picture, the Channel [V]’s status is bypass, now we want to change the
status.

Click the program which you want to edit (in the picture, it is Channel [V], NO.21), then
this program will be high bright blue, program number will show in “Program Number”

item. Then click the down list menu in the “program operation” item to select the status

you need.

Explain:

 Bypass: The receiver will do nothing on this program just transfer it to the output port.
 CI slot1: Use the CAM card in slot1 to descramble this program and then transfer it to

the output port.

 CI slot2: Use the CAM card in slot2 to descramble this program and then transfer it to

the output port.

 Delete: Do not transfer this program to the output port, filtrate this program.

UMH 150 Integrated Receiver Decoder User Manual

22

Ⅷ. Programs play

In this box, select the programs you want to play, and then click “SendData” button to save
the parameters, the programs you select will be played.

Ⅸ. Status

This box is used to display the information about palying program, CI slot, Tuner status and
TS rate.

Ethernet:
Ⅹ. IP Receiver

 Enable: When the programs are from IP source, select on.
 Protocol: Optional UDP and RTP.
 Enablechannel: When the programs are from IP source, select on.
 UDPDestPort: Set up the UDP port for receiving the IP signal.
 IPDestAddress: Set up the multicast IP address for receiving the IP signal.

Other parameters: Default setting.

UMH 150 Integrated Receiver Decoder User Manual

23

Ⅺ. Transmitter

 ChannelSelect: Set up the channel number where you want to transmit programs.
 EnableChannel: Enable or disable the channel.
 Protocol: Optional UDP or RTP.
 EncapNum TSPackts: Configuration range is 1—7.(7 is recommended).
 TypeOfService: It includes Normal, Min onetary, Max reliabiability, Max Throughput,

Min delay.

 TimeToLive: Configuration range is 1-5.(5 is recommended).
 IPDestAddress: Set up the channel’s multicast IP for broadcasting the IP signal.
 UDPDestPort: Set up the UDP port for broadcasting the IP signal.

Other parameters: Default setting.

Ⅻ. Program list

In this part, you can see the information of the programs which is in the selected channel.
You can determine which program will be transmitted by changing the status of ‘Operation’
in the list.

Upgrade:

You can upgrade the new software by this NMS conveniently. Click ‘Upgrade’ button, then
select a desired document, then NMS will upgrade for UMH150 automatically.

UMH 150 Integrated Receiver Decoder User Manual

24

Problem

Possible causes

What to do

The display on the front
panel does not light up.

No power.

Check that the main cable is
plugged into the power socket.

The front panel red light is
on. AV has no output.

The unit is in standby mode
or no output connection.

Check the output connection or
Press the standby button.

TV is not in AV mode.

Set TV in AV mode.

No or bad signal.
No cable connection or the

program does not exist in
the current satellite.

Check the cable connections,
LNB and other equipment
connected between the LNB
and the STB, and /or adjust the
dish.

The satellite dish is not
facing the satellite.

Adjust the dish. Check the
signal level in the antenna
setup menu.

Bad picture / Blocking
error.

The satellite dish is not
facing the satellite.

Adjust the dish.

Signal is too strong.

Connect a signal attenuator to
the LNB input.

Signal is too weak.

Change to a larger dish.

LNB noise figure is too
high.

Change to a LNB with a lower
noise figure.

The LNB is defect.

Change the LNB.

Troubleshooting

UMH 150 Integrated Receiver Decoder User Manual

25

Problem

Possible causes

What to do

Signal is good. But No
picture and no audio.

The picture and audio are
scrambled.

Change to a FTA channel.

There is interference on
your digital satellite
channel.

The system is connected
with RF leads and the
output channel of the
receiver interferes with an
existing terrestrial channel
or video signal.

Change the receiver output
channel to a more suitable
channel.

Network remote can not
connect

IP stetting

Check the PC IP and
equipment IP

Cable is not good

Make sure the cable is good
one and connect well.

No output on ASI or output
unstable.

BNC Connection loosing.

Make sure that ASI output
cable connect with the output
port
tightly.

Cannot Decrypt Programs.

Don’t select decrypted

programs or select
incorrectly.

Select decrypted programs to
be correctly.

CAM Modular Error.

Change for another CAM.

Smart Card no right.

Contact the content provider.

Incorrect insertion of CAM
or Smart card.

Correctly insert CAM and
Smart card.

UMH 150 Integrated Receiver Decoder User Manual

26

Specifications

Tuner

Frequency Range

950~2150MHz

Symbol Rate

2~45Mband

Signal Strength

-65~-30dBm

FEC Mode Rate Demodulation

1/2,2/3,3/4,5/6,7/8QPSK

Audio

Audio Decoding

MPEG layer I & II

Audio Mode

Mono/Dual Channel/Stereo

Connectors

RCA (L , R)

Video

Video Decode

MPEG-II ISO/IEC 13818-1

Input Bit Rate

<=15Mbps

Output System

PAL/NTSC/SECAM

Video Resolution

720×576

Connectors

RCA

TS output

Connectors

BNC

Interface Type

ASI

Impedance

75Ω

Packet

188/204

Bit rate

1~72Mbps

TS Format

Single / Multiple programs

TS input

Connectors

BNC

Interface Type

ASI

Bit rate

Up to 82Mbps

Working

condition&

Physical

Specification

Power supply voltage

AC: 170~260V (or 90~130V),

50/60Hz

Power consumption

20W(Max)

Temperature

0℃~40℃

Humidity

10%~90%

Size (W×D×H)

42mmH×484mmW×335mmD

Net Weight

4.2 Kg

UMH 150 Integrated Receiver Decoder User Manual

27

UMH150F

UMH150CI

UMH150IP

-S

-C

-T

­S2

-S

-C

-T

­S2

-S

-C

-T

­S2

DVB-S input/loop through
output

√ √ √

DVB-C input/loop through
output

√ √ √

DVB-T input/loop through
output

√ √ √ DVB-S2 input/loop
through output

√ √

√

IP input

√ √ √

√

IP output

√ √ √

√

CI slot x 2

√ √ √ √ √ √ √ √ Audio Balance

√ √ √ √ √ √ √

√

SDI output

√ √ √ √ √ √ √

√

ASI input

√ √ √ √ √ √ √

√

ASI output

√

√

√ √ √ √ √ √ √ √ √ √ YPbPr output

√ √ √ √ √ √ √ √ √ √ √

√

CVBS output

√ √ √ √ √ √ √ √ √ √ √ √ LAN remote (SNMP)

√ √ √ √ √ √ √ √ √ √ √

√

Model

Function

Optional Models

Note: The icon √ represents the model with this function.

UMH 150 Integrated Receiver Decoder User Manual