Page 1
®
CP139-40 Rev A
Weldmatic 350i + Weldmatic 500i
Weldmatic 350i
Multiprocess welder
Model No. CP139-2
Iss A
Operators Manual
01/16
Weldmatic 500i
Multiprocess welder
Model No. CP140-2
Iss A
Page 2
Welding Industries of Australia
A division of ITW Australia Pty Ltd
1300 300 884
Info@welding.com.au
welding.com.au
Page 3
Weldmatic 350i + Weldmatic 500i
Model No CP139, CP140 1
Contents
Section General Information Page
Safe Practices 2
1 Introduction 5
2 Receiving 6
3 Specifications 7
4 Controls 8
5 Installation 10
6 Normal Welding Sequence 12
7 Basic Welding Information 12
8 General Maintenance 18
9 External Trouble Shooting 19
10 Service Information 20
10.1 Circuit Diagram 21
11 Assembly and Parts Lists 22
12 Warranty information 24
Page 4
2
Operators Manual
Trusted by the best
Read First
The information contained in this
manual is set out to enable you
to properly maintain your new
equipment and ensure that you obtain
maximum operating efficiency.
Please ensure that this information is
kept in a safe place for ready reference
when required at any future time.
When ordering spare parts, please
quote the model and serial number
of the power source and part number
of the item required. All relevant
numbers are shown in lists contained
in this manual. Failure to supply this
information may result in unnecessary
delays in supplying the correct parts.
Safety
Before this equipment is put into
operation, please read the Safe
Practices section of this manual.
This will help to avoid possible injury
due to misuse or improper welding
applications.
Plastic Handles on Power
Source
Please note that the handles fitted
to the Weldmatic power source are
intended for carrying the equipment
by hand only.
DO NOT use these handles for
suspending or mounting the power
source in any other manner.
Safe Practices When Using
Welding Equipment
These notes are provided in the interests
of improving operator safety. They should
be considered only as a basic guide to Safe
Working Habits. A full list of Standards
pertaining to industry is available from
the Standards Association of Australia,
also various State Electricity Authorities,
Departments of Labour and Industry or
Mines Department and other Local Health
or Safety Inspection Authorities may have
additional requirements. Australian Standard
AS1674.2 provides a comprehensive guide to
safe practices in welding.
Eye Protection
NEVER LOOK AT AN ARC WITHOUT
PROTECTION. Wear a helmet with
safety goggles or glasses with side shields
underneath, with appropriate filter lenses
protected by clear cover lens. This is a MUST
for welding, cutting, and chipping to protect
the eyes from radiant energy and flying
metal. Replace the cover lens when broken,
pitted, or spattered.
Recommended Shade Filter Lens
Amps TIG MMAW MIG
Pulsed
MIG
0-100 10 9 10 12-13
100-150 11 10 10 12-13
150-200 12 10-11 11-12 12-13
200-300 13 11 12-13 12-13
300-400 14 12 13 14
400-500 — 13 14 14
500 + — — 14 14
Page 5
Weldmatic 350i + Weldmatic 500i
Model No CP139, CP140 3
Burn Protection
The welding arc is intense and visibly bright.
Its radiation can damage eyes, penetrate
light-weight clothing, reflect from lightcoloured surfaces, and burn the skin and
eyes. Burns resulting from gas-shielded arcs
resemble acute sunburn, but can be more
severe and painful.
Wear protective clothing – leather or heat
resistant gloves, hat, and safety-toed boots.
Button shirt collar and pocket flaps, and
wear cuffless trousers to avoid entry of
sparks and slag.
Avoid oily or greasy clothing. A spark may
ignite them. Hot metal such as electrode
stubs and work pieces should never be
handled without gloves.
Ear plugs should be worn when welding in
overhead positions or in a confined space.
A hard hat should be worn when others are
working overhead.
Flammable hair preparations should not be
used by persons intending to weld or cut.
Toxic Fumes
Adequate ventilation with air is essential.
Severe discomfort, illness or death can
result from fumes, vapours, heat, or oxygen
depletion that welding or cutting may
produce. NEVER ventilate with oxygen.
Lead, cadmium, zinc, mercury, and beryllium
bearing and similar materials when welded
or cut may produce harmful concentrations
of toxic fumes. Adequate local exhaust
ventilation must be used, or each person in
the area as well as the operator must wear
an air-supplied respirator. For beryllium, both
must be used.
Metals coated with or containing materials
that emit fumes should not be heated unless
coating is removed from the work surface,
the area is well ventilated, or the operator
wears an air-supplied respirator.
Work in a confined space only while it is
being ventilated and, if necessary, while
wearing air-supplied respirator.
Vapours from chlorinated solvents can be
decomposed by the heat of the arc (or
flame) to form phosgene, a highly toxic
gas, and lung and eye irritating products.
The ultra-violet (radiant) energy of the arc
can also decompose trichlorethylene and
perchlorethylene vapours to form phosgene.
Do not weld or cut where solvent vapours
can be drawn into the welding or cutting
atmosphere or where the radiant energy
can penetrate to atmospheres containing
even minute amounts of trichlorethylene or
percholorethylene.
Fire and Explosion Prevention
Be aware that flying sparks or falling slag can
pass through cracks, along pipes, through
windows or doors, and through wall or floor
openings, out of sight of the operator. Sparks
and slag can travel up to 10 metres from the arc.
Keep equipment clean and operable, free of
oil, grease, and (in electrical parts) of metallic
particles that can cause short circuits.
If combustibles are present in the work
area, do NOT weld or cut. Move the work if
practicable, to an area free of combustibles.
Avoid paint spray rooms, dip tanks, storage
areas, ventilators. If the work can not be
moved, move combustibles at least 10 metres
away out of reach of sparks and heat; or
protect against ignition with suitable and
snug-fitting fire-resistant covers or shields.
Walls touching combustibles on opposite
sides should not be welded on or cut. Walls,
ceilings, and floor near work should be
protected by heat-resistant covers or shields.
Page 6
4
Operators Manual
Trusted by the best
A person acting as Fire Watcher must be
standing by with suitable fire extinguishing
equipment during and for some time after
welding or cutting if;
• Combustibles (including building
construction) are within 10 metres.
• Combustibles are further than 10 metres
but can be ignited by sparks.
• Openings (concealed or visible) in floors
or walls within 10 metres may expose
combustibles to sparks.
• Combustibles adjacent to walls, ceilings,
roofs, or metal partitions can be ignited
by radiant or conducted heat.
After work is done, check that area is free of
sparks, glowing embers, and flames.
A tank or drum which has contained
combustibles can produce flammable
vapours when heated. Such a container must
never be welded on or cut, unless it has first
been cleaned as described in AS.1674-2.
This includes a thorough steam or caustic
cleaning (or a solvent or water washing,
depending on the combustible’s solubility),
followed by purging and inerting with nitrogen
or carbon dioxide, and using protective
equipment as recommended in AS.1674-2.
Water-filling just below working level may
substitute for inerting.
Hollow castings or containers must be vented
before welding or cutting. They can explode.
Never weld or cut where the air may contain
flammable dust, gas, or liquid vapours.
Shock Prevention
Exposed conductors or other bare metal
in the welding circuit, or ungrounded
electrically alive equipment can fatally shock
a person whose body becomes a conductor.
Ensure that the equipment is correctly
connected and earthed. If unsure have the
equipment installed by a qualified electrician.
On mobile or portable equipment, regularly
inspect condition of trailing power leads and
connecting plugs. Repair or replace damaged
leads.
Fully insulated electrode holders should be
used. Do not use holders with protruding
screws. Fully insulated lock-type connectors
should be used to join welding cable lengths.
Terminals and other exposed parts of
electrical units should have insulated knobs
or covers secured before operation.
IMPORTANT NOTICE: Warranty may
be voided if equipment is powered
from an unsuitable engine driven
generator.
Generators used to power
this equipment must have the
recommended minimum capacity and
incorporate output voltage regulation.
Due to variation between generators by
different manufacturers, it is impossible
for WIA to validate operation from all
generators. Therefore, we recommend
that operation of equipment on
the generator is received from the
manufacturer before purchasing the
generator.
Page 7
Weldmatic 350i + Weldmatic 500i
Model No CP139, CP140 5
1 Introduction
The Weldmatic is a multiprocess welding
machine capable of Gas Metal Arc Welding
(GMAW or MIG), Manual Metal Arc Welding
(MMAW or Stick) and Gas Tungsten Arc
Welding (GTAW or TIG).
GMAW (MIG Welding)
Gas Metal Arc Welding (GMAW) is an arc
welding process where a consumable wire is
fed by motor driven feed rolls to a welding
gun, and where welding current is supplied
from the welding power source. The welding
arc is struck between the work piece and
the end of the wire, which melts into the
weld pool. The arc and the weld pool are
both shielded by gas flow from the gun, or
in the case of “self shielded” wires, by gases
generated by the wire core.
The process is very versatile in that by
selection of the correct wire composition,
diameter and shielding gas, it can be used
for applications ranging from sheet-metal to
heavy plate, and metals ranging from carbon
steel to aluminium alloys.
The Weldmatic has been designed to be
used with consumable wires of different
diameter. The smaller wire sizes are used
when welding at lower currents, such as
sheet-metal applications. Increasing the wire
diameter permits higher welding currents to
be selected.
A common application of GMAW is for
welding Mild Steel. In this application, a
Mild Steel solid consumable wire such as
AUSTMIG ES6 is used with a shielding gas
of Carbon Dioxide, or Argon mixed with
Carbon Dioxide. Alternatively, Flux-cored
consumable wires are available in both gas
shielded, and ‘gasless’ self shielding types.
Stainless steel and Aluminium can be welded
with GMAW using the correct consumable
wire and shielding gas.
The Weldmatic wirefeeder has been designed
to feed a range of hard, soft, and flux-cored
wires for the GMAW process. A compact
motor with integral gear box is coupled to
a two roll drive assembly forming the basic
component of the wirefeeder. The motor
is controlled by an electronic speed control
which provides speed regulation.
MMAW (Stick Welding)
Manual Metal Arc Welding (MMAW) is a
process where an arc is struck between a
flux-coated consumable electrode and the
work piece. The arc and the weld pool are
both shielded by gases generated by the flux
coating of the electrode.
The Weldmatic has been designed to be used
with 2.0mm, 2.5mm, 3.2mm and 4.0mm
diameter electrodes. The smaller electrodes
are used when welding at lower currents,
such as sheet metal applications. Increasing
the electrode diameter permits higher welding
currents to be selected.
WIA supplies a wide range of mild steel and
special purpose electrodes which cater for home
workshop, rural, and industrial requirements.
Some popular AUSTARC electrodes are listed
below. The correctly selected AUSTARC
electrode will influence the quality of the weld,
and the stability of the arc.
Austarc 12P, Classification E4313-A
A popular general purpose electrode used
with ease in all positions, vertical up or
down. The smooth forceful arc makes it
an ideal electrode for all general mild steel
applications.
Austarc 13S, Classification E4313-A
A smooth running electrode with a soft arc,
particularly suited to light sheetmetal and
smooth mitre fillet welds.
Page 8
6
Operators Manual
Trusted by the best
Austarc 16TC, Classification E4916-A
A low hydrogen electrode with good
arc stability and out-of-position welding
characteristics. This electrode is ideal for
medium carbon steels, or steels of unknown
analysis.
Austarc 11, Classification E4311-A
A high cellulose electrode for all positional
welding, AC or DC. Particularly suited for
vertical and incline pipe welding where
complete root penetration is required.
Unicord 312, Classification ES312-16
A high tensile (50tsi), chromium nickel
electrode specially formulated for joining all
alloy steels and irons, and for tool and die
maintenance.
GTAW (TIG Welding)
Gas Tungsten Arc Welding (GTAW) is a
welding process where the arc is struck
between a non-consumable tungsten
electrode and the work piece. A ceramic
nozzle surrounds the tungsten electrode and
directs a flow of inert gas, usually Argon, over
the electrode and the weld zone. If filler metal
is required, it is hand fed into the welding arc.
The DC current output of the Weldmatic is
suitable for welding most ferrous and nonferrous metals, but is not suitable for welding
Aluminium for which an AC machine is
required.
2 Receiving
Check the equipment received against the
shipping invoice to make sure the shipment
is complete and undamaged. If any damage
has occurred in transit, please immediately
notify your supplier.
The Weldmatic 350i package contains;
• CP139-2 Weldmatic 350i power source.
• Argon gas regulator.
• Gas hose
• Welding torch – 350 AMP fitted with
Bernard 0.9 centre fire tip
• Work lead and spring clamp - 10m
x 35mm2 cable with large twist lock
connector.
• W66-0 wire feeder with 4 roll drive.
• Feed roller V0.9/1.2mm with Vgroove
quantity 2 fitted
• Feed roller V0.9/1.2mm with teeth
(knurled) quantity 2 spare
• Composite lead 35mm2 10M
• AM358 trolley with drawers
• Owners Manual CP139-40 issue A.
The Weldmatic 500i package contains;
• CP140-2 Weldmatic 500i power source.
• Argon gas regulator
• Welding torch - 400amp fitted with
0.9mm Bernard centre fire tip
• Work lead and clamp - 10m x 50mm2
cable terminated with G clamp
• W65-0 wire feeder with heavy duty 4
roll drive
• Feed roller V0.9/1.2mm with Vgroove
quantity 2 fitted
• Feed roller V0.9/1.2mm with teeth
(knurled) quantity 2 spare
• COMPOSITE LEAD 50mm2 10M
• AM358 Trolley with drawers
• Owners Manual CP139-40 issue A.
Optionally available
• TIG Torch Complete DGT26FX8M20058F,
8m cable with twist-lock connection and
fitted with 2.4mm collet.
Page 9
Weldmatic 350i + Weldmatic 500i
Model No CP139, CP140 7
3 Specifications
350i 500i
Manufactured to Standards AS60974.1 IEC60974.10 AS60974.1 IEC60974.10
Rated Input Voltage 380 – 415V 3 Phase 380 – 415V 3 Phase
Power Frequency 50/60 Hz 50/60 Hz
Generator Three Phase Capacity 15KVA 25KVA
Rated Maximum Supply Current
Imax
25A 37A
Maximum Effective Supply
Current Ieff
19.4A 28.7A
Output No Load Voltage 65V 65V
VRD Safe 4.1V 4.1V
MIG GMAW
350Amp @ 31.5V 60% Duty 500Amp @ 39V 60% Duty
271Amp @ 27.6V 100% Duty 387Amp @ 33.4V 100% Duty
Stick MMA
350Amp @ 34V 60% Duty 490Amp @ 39.6V 60% Duty
271Amp @ 30.8V 100% Duty 380Amp @ 35.2V 100% Duty
TIG
350Amp @ 24V 60% Duty 500Amp @ 30V 60% Duty
271Amp @ 20.8V 100% Duty 387Amp @ 25.5V 100% Duty
Spool Size ES6 – 5kg & 15kg ES6 – 5kg & 15kg
Supply Plug 32A 32A
Supply Cable 2.5mm2 3 Core + E Heavy
Duty PVC
4.0mm2 3 Core + E Heavy
Duty PVC
Mains Circuit Breaker Rating 25A 32A
Wire Speed Range 0-15 Metre/sec 0-20 Metre/sec
Wire Size 0.8, 0.9, 1.2 mm Solid Wire
0.8 - 1.2 mm Cored Wire
0.8, 0.9, 1.6 mm Solid Wire
0.8 - 1.6 mm Cored Wire
Cooling Type Fan on Demand Fan On Demand
Efficiency ≥ 85% ≥ 85%
Power Factor 0.92 0.92
Insulation H 140°C Rise H 140°C Rise
Protection IP21S IP21S
Weight 93kg 96kg
Shipping Weight 104kg 107kg
Dimension L × W × H 705 x 307 x 500mm 705 x 307 x 500mm
Shipping Dimension L × W × H 1070 x 550 x 1080mm 1070 x 550 x 1080mm
Page 10
8
Operators Manual
Trusted by the best
AMPS
AMPS
VOLTS
ARC FORCE
A175NIW
WELDMATIC
VS
350i
WELD AMPS WELD VOLTS
350
271
31.5
60% 100%
27.6
LOCAL
CORED WIRE:
- Self Shielded
- Gas Shielded
- All Sizes
REMOTE
He
Fig 1 Weldmatic 350i + 500i Controls
1 Control Panel
2 Remote Connector
There are two remote connectors, the larger
one is for the wire feeder connection and
the other is for a remote control connection,
such as a TIG torch.
3 Positive Welding Output Terminal
4 Negative Welding Output Terminal
5 Gas Connection
6 Power On Indicator
7 VRD Safe Light
VRD safe light is on when the machine is
in stick mode and the open circuit output
voltage is reduced to a safe level.
8 Over Temperature Warning
If an over temperature condition is reached
the machine will prevent weld output and
wait until machine has cooled down, before
welding output can commence.
9 Digital Display Amps
If Weld Mode is stick MMA Mode or TIG
mode the display will indicate the selected
welding Amps when adjusted with knob,
item (10).
During welding in any mode, the display will
show actual welding Amps.
10 Weld Current Adjustment
Weld Current Adjustment Knob for Stick
MMA or TIG Mode.
4 Controls
1211 6
7 8 14
10
9
15
13
16
3
1
45 2
Page 11
Weldmatic 350i + Weldmatic 500i
Model No CP139, CP140 9
11 Digital Display Volts
MIG Mode (GMAW): the display will
indicate Actual weld volts.
Stick Mode (MMA): the display will indicate
the amount of Arc Force 0-10 set by Knob
(12).
Voltage Sensing (VS): the display will
indicate the weld volts setting set by Knob
(12).
12 Voltage Adjustment Knob
When in Stick MMA Mode the knob will
adjust Arc force 0-10.
When the welding machine detects a sudden
drop in the weld arc voltage, the machine
will compensate momentarily by increasing
the weld current and weld voltage.
A higher arc force might be useful for
difficult electrodes such as Cellulose.
If Weld Mode is Voltage Sensing VS the knob
will adjust the weld volts setting
13 Mode Selection Button
Pressing the button will cycle through each
of the six welding modes as indicated by the
six lights. The Six Modes are:
13.1 Stick electrode welding MMA, with
LOCAL control: The two knobs will adjust
Weld amps and Arc force.
13.2 Stick electrode welding MMA, with
REMOTE control: The two knobs will adjust
maximum Weld amps and Arc force. The
remote control will provide arc start switch
and knob control of weld amps, up to the
maximum AMPS setting.
13.3 GMAW MIG using remote wire
feeder: The weld voltage is controlled from
the wire feeder and the set value is displayed
on (11). The output voltage is only active
when signaled from the wire feeder.
13.4 TIG GTAW welding, LOCAL control:
Lift arc start, using TIG welding torch with
separate gas supply.
Knob (10) will adjust the weld current which
is displayed on (9).
13.5 TIG GTAW welding REMOTE
control: Lift arc start, using TIG welding
torch with separate gas supply.
Knob (10) will adjust the Maximum weld
current which is displayed on (9).
The remote control will provide arc start
switch and knob control of weld amps, up to
the maximum setting.
13.6 MIG Mode Voltage Sensing VS: The
Knob (12) will adjust the weld volts setting,
which is displayed on (11).
The output terminals are at full OCV. This
mode requires a special wire feeder that
is capable of operating from output live
terminals.
14 Wire select Button and Indicator
Use this button to select the wire size being
used. Sizes 0.9, 1.2, 1.6mm can be used.
When wire setting is set to Gasless then
there is no need to select wire size.
15 Gas Select button and indicator
Use this button to select which type of gas is
being used, or if Gasless wire is being used.
Ar: Argon is typically used for Aluminium
welding and Silicon Bronze welding.
Ar/He: Argon Helium is used for stainless
steel.
Ar/CO2: Is used for Argon CO2 mixed gas
There are a variety of gas mixes available.
Argon CO2 is typically used on thicker steel,
Argon CO2 O2 mix is used for thin steel.
Page 12
10
Operators Manual
Trusted by the best
5 Installation
Connection to Electrical Mains Power
Supply
Note: All electrical work shall only be
undertaken by a qualified electrician.
350i
The Weldmatic 350i is factory fitted with a
3 metre, 3 core+ earth 2.5mm2 Heavy Duty
PVC mains power supply cable.
The power cable is fitted with a 32 amp 3
phase plug.
Maximum rated output
To achieve the rated output of 350A 60%
the machine requires maximum primary
current Imax 25A and Effective primary
current Ieff 20 Amps.
The machine needs to be fitted with a
plug capacity 20A or greater, and a supply
capacity 25A or greater.
The minimum recommended supply circuit
breaker rating for a Weldmatic 350i is 25
Amps.
500i
The Weldmatic 500i is factory fitted with a
3 metre, 3 core+ earth 4.0mm2 Heavy Duty
PVC mains power supply cable.
The power cable is fitted with a 32 amp 3
phase plug.
Maximum rated output
To achieve the rated output of 500A 60%
the machine requires maximum primary
current Imax 37A and Effective primary
current Ieff 30 Amps.
The machine needs to be fitted with a
plug capacity 32A or greater, and a supply
capacity 28.7A or greater.
CO2: Is a cheaper gas option for steel when
weld spatter and finish is not a concern.
16 Arc Control
When in MIG GMAW mode the harshness
of the arc can be adjusted. For example
aluminium welding would require a different
setting to steel welding.
Page 13
Weldmatic 350i + Weldmatic 500i
Model No CP139, CP140 11
The minimum recommended supply circuit
breaker rating for a Weldmatic 500i is 32
Amps.
Successful operation
Successful operation will depend on a
number of factors:
• Variation in circuit breaker thresholds.
• Ambient temperature.
• Number of previous circuit breaker
operations.
• Actual weld conditions, resulting in
higher weld currents.
• Repeated starts can result in repeated
in-rush currents raising circuit breaker
threshold.
Repeated circuit breaker operation at weld
start can sometimes be overcome by using a
“D” curve circuit breaker.
To reduce nuisance tripping, a higher
rated circuit breaker can be selected, but
the supply circuit wiring capacity must be
increased to suit.
Supply Cable
If it becomes necessary to replace the mains
flexible supply cable, use only cable with
correct current rating.
The replacement cable must be fitted and
retained in the same manner as the original.
Output Voltage Polarity
The design of the Weldmatic allows selection
of the output voltage polarity.
Positive Wire
MIG welding (GMAW), with solid
consumable wires and gas shielding, is
carried out with the work piece Negative and
the welding wire Positive.
To setup for this condition, connect the
‘WORK’ lead plug into the (-) output terminal
on the power source, and the wirefeeder
weld cable into the (+) output terminal.
Negative Wire
Some ‘self-shielded’ flux cored gasless
consumable wires are operated with the
work piece Positive and the consumable wire
Negative. Refer to the manufacturers data for
the particular consumable wire to be used.
To setup for this condition, connect the
‘WORK’ lead plug into the (+) output
terminal on the power source, and the
wirefeeder weld cable into the (-) output
terminal.
Fitting the Gas Cylinder
Place the gas cylinder on the tray at the
rear of the optional welder trolley (if using).
Retain the cylinder with the chain provided.
Fit the gas regulator to the cylinder. DO NOT
apply grease or oil to these joints.
Fit the end of the gas inlet hose from the
back of the power source to the connector
supplied with the gas regulator, and secure
with the clamp also supplied.
Page 14
12
Operators Manual
Trusted by the best
7 Basic Welding Information
MIG Welding (GMAW)
Choice of Shielding Gas
The choice of shielding gas is largely
determined by the consumable wire to
be used. Many proprietary shielding gas
mixtures are available.
Some recommended shielding gases are:
• Mild Steel Argon + 18% Oxygen ;
Argon + 2% Oxygen +
5% Carbon dioxide;
• Aluminium Argon;
• Stainless Steel Argon + 1 to 2%
Oxygen.
Argon + Helium
Consult your gas supplier if more specific
information is required.
Shielding Gas Flow Rate
In GMAW, one function of the shielding gas
is to protect the moulten weld pool from the
effects of oxygen in the atmosphere. Without
this protection the weld deposit becomes
‘honeycombed’ in appearance, an effect
which is described as weld porosity.
In draft-free conditions the gas flow rate
required to give adequate protection is
typically 10-12 litres/min. In situations where
drafts cannot be avoided, it may be necessary
to increase this rate up to 20 litres/min,
and/or to provide screening of the work area.
Weld porosity can also be caused by air
entering the gas stream through a damaged
hose, loose gas connection, or from
restriction in the nozzle, such as from excess
build-up of spatter.
When welding aluminium, particular care
must be taken with all aspects of shielding
gas delivery and workpiece preparation in
order to avoid weld porosity.
6 Normal Welding Sequence
Weld Start
Closing the welding gun switch initiates
this sequence of events:
• The gas valve is energised and gas flow
commences;
• Welding voltage is applied between the
work piece and the consumable wire.
• The wire drive motor is energised.
• The wire touches the work piece, and
the arc is established.
Weld End
Releasing the gun switch initiates this
sequence of events:
• The wire drive motor is de-energised,
and is dynamically braked to a stop;
• The welding current stops.
• The gas valve is de-energised and the
flow of shielding gas ceases.
The quality of the consumable wire
greatly affects how reliably a gas
metal arc welder will operate. For best
results when welding mild steel, we
recommend quality WIA AUSTMIG ES6.
Dirty, rusty or kinked wire will not feed
smoothly through the gun cable and
will cause erratic welding. Deposits from
the wire will clog the gun cable liner
requiring it to be replaced prematurely.
Page 15
Weldmatic 350i + Weldmatic 500i
Model No CP139, CP140 13
Establishing a Weld Setting
Once the consumable wire type, wire size
and shielding gas have been chosen, the two
variables that are adjusted in order to obtain
a the desired weld setting are;
• Wirefeed speed,
• Welding arc voltage.
The wirefeed speed determines the welding
current; increasing the speed increases the
current, and decreasing it decreases current.
The selected wirefeed speed must be
matched with sufficient arc voltage; a speed
increase requires an increase of arc voltage.
If the voltage is too low the wire will stub
and stutter, and there will not be a steady
arc. If the voltage is too high the arc will be
long with metal transfer occurring as a series
of large droplets.
The weld setting should be chosen to suit the
application and the thickness of the metal to
be welded. It is important to check that the
deposited weld provides sufficient strength
to suit the application.
A “good” weld will have the characteristics
illustrated in Figure 2. The weld has penetrated
into the parent metal, fusing the root of the
joint where the two plates meet, and the weld
blends smoothly into the side walls.
A “bad” weld is shown in Figure 3. The weld
has not penetrated the joint root, and there
is poor side wall fusion. This lack of fusion
would normally be corrected by increasing
the arc voltage, or by increasing both
wirefeed speed and arc voltage to achieve a
higher current weld setting.
Fig 2 “Good” Weld
Fig 3 “Bad” Weld
Page 16
14
Operators Manual
Trusted by the best
Gun Position
For “down hand” fillet welding with gas
shielded solid wires, the gun is normally
positioned as shown in Figure 4a below, with
the nozzle end pointing in the direction of
travel.
For “down hand” fillet welding with
gasless flux cored wires, the gun is normally
positioned as shown in Figure 4b, with the
nozzle end pointing away from the direction
of travel, referred to as ‘dragging’ the weld.
Gasless flux cored wires should be operated
with approximately 10-15mm of wire ‘stickout’ from the welding contact tip as shown
in Figure 4c.
10-
Fig 4a Gas Shielded Solid Wires
Fig 4b Gasless Flux Cored Wires
Fig 4c Wire Stickout for Gasless Welding
Page 17
Weldmatic 350i + Weldmatic 500i
Model No CP139, CP140 15
Stick Welding (MMAW)
Connection for Stick Welding
It is important to select the electrode polarity
in accordance with the manufacturers
recommendations for that electrode. Most
common electrodes, including cellulose
types, are operated with the electrode at
positive polarity.
Stick Welding Operation
Be certain that you are wearing suitable
protective clothing, gloves etc and that you
are working in a non-hazardous area. If
necessary, refer again to Section 1 - Safe
Practices in this manual.
Connect the work clamp to the work piece.
Place the desired electrode in the electrode
holder (electrode holder optional extra).
Turn on the power switch located on the rear
panel. Wait approximately 5 seconds as the
unit goes through its initiation sequence.
Press the Weld Mode button until the Stick
Mode light is on.
Select an appropriate welding current for
the electrode diameter by setting the knob
on the machine front panel. WIA AUSTARC
electrodes will give the best results.
To strike the arc, drag the end of the
electrode along the work piece as if striking
a match. As the arc initiates, lift the electrode
slightly away, aiming to establish an arc
length of approximately 3 mm.
As the electrode end is consumed, feed the
electrode into the arc in order to maintain
arc length. As a general rule, the arc should
be held as short as possible while still giving
stable burn off and good weld appearance.
An arc which is too long cause an unwieldy
flow of metal with a rough weld appearance
and reduced penetration.
An arc too short leads to a narrow weld
deposit and “stuttery” arc characteristics, and
the electrode is liable to freeze onto the work
piece.
As the solidified weld deposit forms, move
the end of the electrode slowly along
the weld path, aiming to maintain a pool
of moulten weld metal behind the arc.
Decreasing this rate of travel will result in a
wider weld deposit, and similarly increasing it
will narrow the weld deposit.
Always fill the crater which tends to form
at the end of a weld deposit, by pausing
momentarily before withdrawing the electrode
to break the arc. Unfilled craters are a point
of weakness, and can lead to weld cracking.
Current Range for General Purpose
Electrodes
Diameter (mm) Current (Amps)
2.0 40 -60
2.5 60 - 85
3.2 90 - 130
4.0 130 - 180
Stick Remote Mode
When in stick remote Mode, the output can
be turned on and off with a remote switch
connected to the remote plug.
Page 18
16
Operators Manual
Trusted by the best
TIG Welding (GTAW)
Connection for TIG Welding
For TIG welding, the torch is connected to
the negative terminal. Welding grade Argon
is the shielding gas most commonly used for
DC GTAW welding. The gas is connected
directly to the torch.
Before first use of the welding torch,
allow gas to purge the torch and hoses for
1 minutes at approximately 10 litres/min. For
welding purposes, the gas flow rate should
be set in the range 2-5 litres/min.
Tungsten electrodes for DC GTAW should
be 1-2% Thoriated or Witstar. This type will
provide the best arc initiation, arc stability and
tip shape retention characteristics. Thoriated
electrodes can be recognised by a red coded
end. The tungsten electrode is ground to
a point, with the grinding marks pointing
towards the tip. For welding currents less
than 20 amps, the included angle of the
point should be 30
o
, for currents greater than
20 amps, the recommended angle is 60
o
.
When set in the torch, the tungsten should
protrude 6 mm from the ceramic gas nozzle.
TIG Welding Operation
Connect the Work Clamp to the work piece.
Turn on the power switch located on the rear
panel. Wait approximately 5 seconds as the
unit goes through its initiation sequence.
Press the Weld Mode button until the TIG
Mode light is on. The Weldmatic keeps the
last mode used in memory, so this step is
only necessary when using a different mode
to that used last.
Select an appropriate welding current for the
job by setting the knob on the machine front
panel.
Use of a copper striking plate can be used to
avoid electrode contamination. The electrode
can also be contaminated by contact with
the filler rod. A contaminated electrode
produces an unstable arc. If this occurs
regrind the electrode tip.
TIG Local / Remote Mode
When in Local Mode the output is turned on
and the LIFT-ARC voltage is present at the
electrode.
When in Remote Mode the output can be
turned on by Torch Trigger switch connected
to the remote plug.
Page 19
Weldmatic 350i + Weldmatic 500i
Model No CP139, CP140 17
1 32 4
Fig 5 Lift TIG Operation Procedure
LIFT TIG Operation
LIFT TIG arc start can be achieved with the
following procedure.
1 Turn on the shielding gas.
2 Touch the electrode lightly against the
work piece.
2 Press the torch trigger switch (if in
remote mode). The shielding gas will
start to flow and a small current will pass
through the electrode.
4 While still holding the electrode against
the work piece, roll the hand piece over
until the cup rests on the work piece.
Use the cup as a pivot point to roll the
hand piece over allowing the electrode to
lift of the work piece.
The arc will ignite.
5 Immediately lift the cup of the work
piece, the current will rise to the welding
level.
Duty Cycle
The term duty cycle indicates the percentage
welding time available at the rated output
current, for each 10 min period over 4 hours.
The Weldmatic 350i is rated at 350 Amps,
and the 500i at 500 Amps, 60% duty cycle.
If the machine is operated at a reduced
welding current, a higher duty cycle is
available. The diagram below illustrates the
appropriate duty cycle rating for the range of
welding currents available, and so allows the
maximum welding time per 10 minute period
to be determined.
The power source is protected by in built
over temperature protection devices. These
will operate if the machine is operated in
excess of its current and duty cycle rating.
If this occurs, the temperature warning
indicator will be on, the fan will continue to
run, but the machine will not deliver welding
current until the unit has cooled sufficiently.
Fig 6 Duty Cycle Rating
Maximum welding
time per 10 min
500
150 200 250 350300 400 450
Page 20
18
Operators Manual
Trusted by the best
Before removing the equipment
cover, ENSURE that the equipment
is disconnected from the mains
power supply. When the equipment
is energised LETHAL VOLTAGES are
present on the electrical components
enclosed.
Dust
Care should be taken to prevent excessive
build-up of dust and dirt within the welding
power source. It is recommended that at
regular intervals, according to the prevailing
conditions, the equipment covers be removed
and any accumulated dust be removed by the
use of dry, low pressure compressed air, or a
vacuum cleaner.
Wirefeed
In order to obtain the most satisfactory
welding results from the GMAW process,
the wirefeed must be smooth and constant.
Most causes of erratic wirefeed can be cured
by basic maintenance. Check that the:
1 Feed rolls are the correct size and type for
the wire in use. Check also that the drive
groove is aligned with the wire, and that
the groove is not worn;
2 Gun cable liner is clear of dust and swarf
build-up. When replacement becomes
necessary, fit only the correct liner. The
build-up of dust can be minimised by
regular purging of the liner with dry
compressed air. This may be conveniently
done each time the wire spool is
replaced;
3 Welding tip is free of obstructions such
as spatter build-up. Ream out the tip
bore with a suitable size oxy-tip cleaner.
Replace the welding tip as it becomes
worn;
4 Feed roll pressure is not excessive. The
pressure should be just sufficient to feed
the wire evenly. Excessive pressure will
deform the electrode wire and make
feeding more difficult;
5 Consumable wire spool holder rotates
smoothly and that the braking action is
not excessive. The spool should only have
sufficient braking to prevent over run
when the motor stops. This also may be
conveniently checked each time the wire
is replenished;
7 Welding wire is straight and free of
buckles or ‘waviness’. To check, remove
2 or 3 metres of wire from the spool.
Clamp one end in a vice or similar, then
holding the other end pull the wire out
straight. Look down the length of the
wire, any buckles will be obvious. Buckled
wire is extremely difficult to feed reliably
and should be replaced;
8 Welding wire is free of surface rust.
Replace if rust is evident.
8 General Maintenance
Page 21
Weldmatic 350i + Weldmatic 500i
Model No CP139, CP140 19
If the following checks do not identify
the fault condition, the equipment
should be returned to a WIA Service
agent. Phone 1300 300 884 for details
of your nearest service agent.
Power source has no output and no
wirefeed when gun switch is closed :
‘ON’ indicator light is not illuminated
1 Check equipment is connected to a
functional mains power outlet. Test outlet
using a known working appliance.
2 Check fuse on rear panel
‘ON’ indicator light is illuminated
1 The gun switch circuit may be incomplete.
• Check the gun switch for continuity
with an ohm meter when the switch
is pressed. Replace if faulty
• Check the 2 pin receptacles in Euro
adaptor are making contact with the
mating pins from the gun Euro end.
2 Power source may have overheated.
• The Weldmatic welding power
source incorporates an in-built
over-temperature thermostat
which will trip if the welding load
exceeds the operating duty cycle.
The ‘OVERLOAD’ light will be
illuminated. The thermostat will reset
automatically - do not switch the
equipment off as the cooling fan will
assist the resetting of the thermostat
9 External Trouble Shooting
• If problem persists after the cool down
period, call your WIA service agent.
Power source has low weld output
1 Check all electrical connections in the
welding current circuit, including weld
cable, work clamp and gun/cable assembly.
Circuit breaker trips during welding
1 Check the rating of the mains supply
circuit breaker. The Weldmatic should be
supplied from a suitable circuit breaker
(refer to section 5).
Unsatisfactory Welding Performance
and Results
Erratic arc characteristics caused by poor
wirefeed
Erratic wirefeed is the MOST LIKELY cause of
failure in all Gas Metal Arc Welding. It should
therefore be the first point checked when
problems occur.
1 Check the torch contact tip is not worn. A
worn tip can cause arcing to the wire inside
the tip and cause the wire to stick and
hesitate
2 Check if the consumable wire is slipping
in the drive rolls. Replace the feed roll if
it is the incorrect size or is worn
Page 22
20
Operators Manual
Trusted by the best
3 Check that gun cable liner is not too
short and is fitted correctly. Refer
wirefeeder manual for fitting instructions.
Constant poor arc characteristics
Check that the:
1 Correct polarity has been selected for
work and weld cables
2 Shielding gas is correct for the
consumable wire in use
3 Welding circuit is making good electrical
connection. Ensure that the work clamp
is securely tightened onto the work piece
so that good electrical contact is achieved
4 All connections in the external welding
circuit are clean and tight. Problems may
show as hot spots
5 Work piece surface is not contaminated.
Water, oil, grease, galvanising, paint,
or oxide layers can severely disturb the
welding arc and result in a poor weld.
Porosity in weld caused by lack of
shielding gas
1 Check that the correct gas flow rate has
been set
2 Check for leaks in the gas hose. Replace
if leaking
3 Check for leaks in gun/cable assembly,
eg. fractured gas hose, broken or missing
‘O’ rings. Replace as required
4 Check the gun nozzle is free from spatter
and is firmly attached to the welding gun
to ensure that no air is being drawn into
the shielded area.
10 Service Information
Before removing the equipment
cover, ENSURE that the equipment
is disconnected from the mains
power supply. When the equipment
is energised LETHAL VOLTAGES are
present on the electrical components
enclosed.
The following information is intended
for use by qualified service personnel.
When the unit is energised LETHAL
VOLTAGES are present on the electrical
and electronic components. It is not
intended that persons without suitable
training and knowledge attempt
to perform service tasks on the
components of this welder.
Page 23
Weldmatic 350i + Weldmatic 500i
Model No CP139, CP140 21
Fig 7 Weldmatic 350i + 500i Circuit Diagram
BR1
SW 1
FAN
SK1
ABC
F
001
002
003
Z27
XS1
XS2
200:1
1
3
4
5
6
7
8
2
9
10
T2
C
1
2
5
6
1'
2'
5'
6'
C1
D10
R2
R11
R15
1
2
5
6
D
4
G
1
S
3
Q2
D1
R1
D5
C3
D9
R6
R12
R16
Q1
D2
R5
D6
C2
D12
R4
R13
R17
1'
2'
5'
6'
Q4
D3
R3
D7
C4
D11
R8
R14
R18
Q3
D4
R7
D8
4
567
4'
5'6'7'
C6
R10
C5
RN1
12345
6
CN1
12345
6
CN2
G1A
G1B
G2A
G2B
C5
C7
R1
V1
C6
123
CN1
Z7
YR1
C7 C8
T1
22:3
ST60N30*6 ST60N30*6
PM500-FR
ZX7-400 QDB
R1
C1
R2
C2
ZX7-400 FZB
T3
FUSE2
X60 375
FUSE3
X60 375
FUSE1
2A
1
2
3
CN3
1
2
CN1
78
78
1
2
3
4
5
6
CN901
PM500-PWM
1
2
3
4
CN2
1
2
3
4
CN102
1
2
3
4
5
6
CN001
12
1
2
CN503
12
1234567
8
CN401
+
1
-
2
O
3
G
4
HE1
500A/4V
3456
910
65439
10
1
2
CN103
14PIN
CN002
PTAP500-CTRL
WeldMatic-MB
1
2
CN401
14PINCN301
19:0:19
AC380V
0:36V
1
2
3
4
5
6
7
8
CN802
1
2
3
4
5
6
CN801
1
2
3
4
5
6
7
8
CN501
Z4
P1+
P2-
C9
D1~D12
1
2
CN402
1314
13
14
2
3
1
45
6 7
GND
Torch Signal
1
2
3
4
CN701
GND
UREF
2
3
1
4
5
+15V
AMPS
REMOTE
Control Cable
123
4
CN502
PM350_RLY
1
2
CN1
P1
P2
PM500-WAY
15PIN
10.1 Circuit Diagrams – Power Source
Page 24
22
Operators Manual
Trusted by the best
AMPS
AMPS
VOLTS
ARC FORCE
A175NIW
WEL
DM
A
TIC
VS
350i
W
ELD A
MPS
W
ELD V
OLTS
350
271
31.5
60%100%
27.6
LOCAL
CORED WIRE:
- Self Shielded
- Gas Shielded
- All Sizes
REMOTE
He
Fig 8 Weldmatic 350i/500i Assembly
11.1 Assembly and Parts List - Weldmatic 350i/500i
2
1
11
14
3
4
5
6
7
8
9
10
12
13
27
26
25
24
23
22
21
15
16
17
18
19
20
Page 25
Weldmatic 350i + Weldmatic 500i
Model No CP139, CP140 23
Item # Part # Description Qty
1/2 M0071 Handle 1
3 PAN164 Enclosure 1
4 L0027 Control Transformer 1
5 E0084 Input Filter 500i 1
5 E0083 Input Filter 350i 1
6 PWA033 PCB Assembly 350i 500i 1
7 E0085 Thermostat 1
8 L0028 Toroid Input 350i 500i 1
9 D0042 Rectifier 3 PH 350i 500i 1
10 D0041 IGBT CP140 500i 1
10 D0040 IGBT CP139 350i 1
11 E0081 Switch On/Off 1
12 FAN015 Fan 350i 1
12 FAN016 Fan 500i 1
13 PWA035 PCB Connection 1
14 PWA034 Output Snubber 1
15 E0086 Current Shunt 1
16 M0076 Front Panel Plastic 1
17 CX58 Weld Terminal Panel Mount Dinse Socket 2
18 E0082 Socket 7 PIN 1
19 TC265 5/8” UNF Nipple 1
20 TC266 5/8” UNF Nut 1
21 M0047 Knob 3
22 WIN571 Front Sticker 350i 1
22 WIN573 Front Sticker 500i 1
23 PWA031 PCB Assy Front Panel 350i 1
23 PWA032 PCB Assy Front Panel 500i 1
24 L0029 Toroid Output 350i 500i 1
25 L0031 Weld Transformer 500i 1
25 L0030 Weld Transformer 350i 1
26 PWA036 PCB Assy PTAP500-CRTL 350i 500i 1
27 PWA037 PCB Assy PM500-WAY 350i 500i 1
WHL002 Wheel Castor 2
WHL003 Wheel Fixed 2
REG003 Argon Regulator 1
CP139-40 Operating Manual 1
62513 Gas Hose
Page 26
24
Operators Manual
Trusted by the best
12 Warranty Information
WIA Weldmatic MIG &
Weldarc MMA Equipment
3 Year Warranty Statement
Welding Industries of Australia (WIA)
warrants to the original retail purchaser
that the Weldmatic welding machine
purchased (Product) will be free from defects
in materials and workmanship for a period
of 3 years from the date of purchase of
the Product by the customer. If a defect in
material or workmanship becomes evident
during that period, Welding Industries of
Australia will, at its option, either:
• Repair the Product (or pay for the costs
of repair of the Product); or
• Replace the Product.
In the event of such a defect, the customer
should return the Product to the original
place of purchase, with proof of purchase,
or contact Welding Industries of Australia on
1300 300 884 to locate an authorised service
agent.
Any handling and transportation costs
(and other expenses) incurred in claiming
under this warranty are not covered by this
warranty and will not be borne by Welding
Industries of Australia. Welding Industries of
Australia will return the replacement product,
if original found to be faulty, freight free to
the customer.
This warranty covers the Weldmatic power
source and wirefeeder only, and does not
extend to the regulator, gun assembly or
accessories included in the original purchase
package.
The obligation of Welding Industries of
Australia under this warranty is limited to the
circumstances set out above and is subject to:
• The customer being able to provide
proof of purchase of the Product and the
purchase price paid for the Product;
• The relevant defect in materials or
workmanship;
• The Product not having been altered,
tampered with or otherwise dealt with
by any person in a manner other than
as intended in respect of the relevant
Product; and
• The Product not having been used or
applied in a manner that is contrary to
customary usage or application for the
relevant Product or contrary to any stated
instructions or specification of Welding
Industries of Australia.
Our goods come with guarantees that
cannot be excluded under the Australian
Consumer Law. You are entitled to a
replacement or refund for a major failure and
for compensation for any other reasonably
foreseeable loss or damage. You are also
entitled to have the goods repaired or
replaced if the goods fail to be of acceptable
quality and the failure does not amount to
a major failure. The benefits given by this
warranty are in addition to other rights and
remedies which may be available to the
customer under any law in relation to goods
and services to which this warranty relates.
Warranty provided by:
Welding Industries of Australia
(ABN 63 004 235 063)
A Division of ITW Australia Pty Ltd
5 Allan Street, Melrose Park,
South Australia, 5039
Ph: 1300 300 884
Email: info@welding.com.au
Web: www.welding.com.au
Page 27
Weldmatic 350i + Weldmatic 500i
Model No CP139, CP140 25
Page 28
Miller Digital Elite Series
™
AUTO-DARKENING HELMETS
Inferno P/N - 257217 Joker P/N - 257218
Lucky’s Speed Shop P/N - 257214 Black P/N - 257213
FOUR MODES –
WELD, CUT, GRIND & X-MODE
Inferno
Joker
Lucky’s
Speed Shop
Black
• Lens and helmet comply with
Australian Standards AS/NZS
1338.1 (Auto-Darkening) and
AS/NZS 1337.1 B (High Impact)
• Lightweight at only 510g.
• Improved digital controls.
• Battery powered with solar assist.
• Lightweight headgear.
• Four independent arc sensors.
• Suits MIG, Stick, Flux-Cored
and Pulse.
• TIG rating 5 Amps.
• 3 year warranty (Auto-Darkening
lens only).
For more information call 1300 300 884 or visit welding.com.au
Loading...